Dansk Standard listestof 2014

Transkript

1 Listestof DS-listestof December 2014 Dansk Standard listestof 2014 Dansk offentliggørelse af nye standarder, forslag til standarder og nationale tekniske forskrifter Nye udgivne standarder og forslag til høring Nye DS-godkendte standarder fra CEN, CENELEC og ETSI Nye harmoniserede standarder Nye tekniske forskrifter fra EU-, EØS- og WTO-lande

2 Dansk Standard listestof 2014 Dansk offentliggørelse af nye standarder, forslag til standarder og nationale tekniske forskrifter Dansk Standard 2014 Grafisk tilrettelæggelse: Dansk Standard Omslag: Dansk Standard Print: Dansk Standard 1. udgave Udgivet af Fonden Dansk Standard Göteborg Plads 1 DK-2150 Nordhavn Telefon: Telefax: dansk.standard@ds.dk Dansk Standards listestof udkommer 12 gange årligt. Abonnement bestilles hos Dansk Standard Forlag og Kundecenter ISSN Dette er en POD-publikation Printet i Danmark

3 Indholdsfortegnelse og brugervejledning til listestoffet 1 ICS-grupper med titler 2 ICS-gruppenumrene er de samme som dem, der anvendes i DS-kataloget, med tilhørende månedlige opdateringer. ICS (international klassifikation af standarder) er udgivet som DS-hæfte 6. Nye udgivne danske standarder og forslag til høring 3 Under de enkelte ICS-grupper er angivet en kort information vedrørende nye forslag og standarder. Der medtages kun de ICS-grupper, hvor der er informationer i indeværende måned. Forslag og standarder bestilles hos Kundecentret. For forslag angives DSF-nummer, og for standarder DS-betegnelsen. Ønskes specifikke informationer, kontaktes den angivne projektleder. Nye DS-godkendte standarder fra CEN, CENELEC og ETSI 88 Samtlige europæiske standarder skal godkendes og udgives som nationale standarder i alle EU-lande i Danmark som danske standarder. Standarderne er inden for CEN, CENELEC og ETSI angivet i EN-nummerrækkefølge med tilhørende dansk godkendelsesdato. Ved køb af EN-standarden anvendes varenummeret. Godkendte EN-standarder foreligger altid på engelsk. Ved den senere udgivelse som DS/EN vil visse af standarderne være oversat til dansk. Standarder og deres relation til de enkelte direktiver 93 Europæiske standarder, der har været offentliggjort i Den Europæiske Unions Tidende (EUT) siden sidste nummer af publikationen Dansk Standard listestof udkom. Oversigten indeholder Rådets direktivtitel og -nummer samt tilhørende numre på EN-standarder. En komplet oversigt, DS-hæfte 1, bestilles hos Kundecentret. Nye anmeldte tekniske forskrifter fra EU-, EFTA- og WTO-lande 94

4 ICS-grupper med titler 2 ICS-nr. Titel 01 Generelt. Terminologi. Standardisering. Dokumentation 03 Sociologi. Serviceydelser. Virksomhedsorganisation og virksomhedsledelse. Administration. Transport 07 Matematik. Naturvidenskab 11 Sundhedsteknologi 13 Miljøbeskyttelse og sundhed. Sikkerhed 17 Metrologi og måling. Fysiske fænomener 19 Prøvning 21 Mekaniske systemer og komponenter til generel brug 23 Hydrauliske og pneumatiske systemer og komponenter til generel brug 25 Produktionsteknik 27 Energi- og varmeoverføringsteknik 29 Elektroteknik 31 Elektronik 33 Telekommunikation. Audio- og videoteknik 35 Informationsteknologi. Kontorudstyr 37 Billedteknologi 39 Finmekanik. Juveler 43 Køretøjsteknik 45 Jernbaneteknik 47 Skibsbyggeri og marine konstruktioner 49 Luft- og rumfartsteknik 53 Udstyr til håndtering af gods 55 Emballage og varedistribution 59 Textil- og læderteknologi 61 Beklædningsindustri 65 Landbrug 67 Levnedsmiddelteknologi 71 Kemisk teknologi 73 Minedrift og mineraler 75 Olieteknologi og beslægtede teknologier 77 Metallurgi 79 Træteknologi 81 Glas- og keramikindustri 83 Gummi- og plastindustri 85 Papirteknologi 87 Farve- og lakindustri 91 Byggematerialer og byggeri 93 Anlægsvirksomhed 95 Militærteknik 97 Udstyr til husholdningsbrug og industriel brug. Underholdning. Sport 99 (Ingen titel)

5 Nye udgivne danske standarder og forslag til høring Terminologi (principper og koordinering) Terminology (principles and coordination) DS/ISO :2014 DKK 489,00 Identisk med ISO :2014 Grafiske notationer for begrebsmodellering i terminologiarbejde samt relationen til UML - Del 1: Vejledning i anvendelse af UML-notation i terminologiarbejde This part of ISO gives guidelines for using a subset of UML symbols independent of their normal UML meaning, to represent concepts in concept models that result from concept analysis. It describes how UML symbols can be used for that. A UML profile designed for this purpose is used to represent concepts and concept relations in terminology work. This part of ISO does not describe UML and its general use in depth. These matters are covered in ISO/IEC and ISO/IEC This part of ISO does not describe the principles and methods of terminology work. This is covered in ISO 704. This part of ISO does not define the fundamental concepts of terminology work. This is covered in ISO Mekaniske systemer og komponenter til almindelig brug (ordliste) Mechanical systems and components for general use (Vocabularies) DS/EN ISO :2014 DKK 700,00 Identisk med ISO :2014 og EN ISO :2014 Befæstelseselementer - Terminologi - Del 2: Ordliste og definitioner for belægninger This part of EN ISO 1891 specifies terms and definitions for fastener coatings, primarily intended for corrosion protection and functional purposes. These terms are mainly intended for use in conjunction with EN ISO 4042, EN ISO and EN ISO A multilingual list of terms in alphabetical order is given in Annex A. Projektleder: Gert Rønnow Produktionsteknik (ordliste) Manufacturing engineering (Vocabularies) DSF M Svarfrist: Identisk med ISO/DIS Relation: ISO Additive fremstillingesmetoder - Rapid prototyping - Del 1: Terminologi This part of ISO establishes and defines terms used in additive manufacturing (AM) technology, which applies the additive shaping principle and thereby builds physical 3D geometries by successive addition of material. The terms have been classified into specific fields of application. New terms emerging from the future work within ISO/TC 261 will be included in upcoming amendments and overviews of this international standard. Projektleder: Hans Henrik Køster Informationsteknologi. Kontormaskiner (ordliste) Information technology. Office machines (Vocabularies) DS/CLC/TR 50584:2014 DKK 446,00 Identisk med CLC/TR 50584:2014 Informationsteknologi - CENELEC-/ETSIordforklaring over termer og definitioner for udrulningen af??bredbånd, herunder bæredygtighedsaspekter This Technical Report contains a list of terms and definitions to be used in standardization deliverables in the field of broadband deployment. These terms and definitions are taken from both published and draft deliverables that were/are being developed by CLC/TC 215 and ETSI/TC ATTM, respectively. NOTE - CLC/TC 215 and ETSI/TC ATTM intended to examine the harmonization of differing terms and definitions in the future Træteknologi (ordliste) Wood technology (Vocabularies) DSF M Svarfrist: Identisk med pren Trægulve - Terminologi This European Standard defines terms and their definitions relating to wood flooring. Projektleder: Erling Trudsø Byggematerialer og byggeri (ordliste) Construction materials and building (Vocabularies) DSF M Svarfrist: Identisk med pren rev Vinduer og døre - Terminologi This European Standard specifies the general terminology for windows and pedestrian doors. The various types are illustrated by figures. Projektleder: Helle Harms Farvesymboler Colour coding DSF M Svarfrist: Identisk med ISO/DIS 6009 og pren ISO 6009 Injektionskanyler til engangsbrug - Farvekode til identifikation This lnternational Standard establishes a colour code for the identification of singleuse hypodermic needles of nominal outside diameters in the range 34G (0,18 mm) to 10G (3,4 mm). It applies to regularwalled, thinwalled and extra-thin-walled and ultrathin walled needles and to opaque and translucent colours. This standard is not applicable for penneedles. Projektleder: Helene Jackson Andre grafiske symboler Other graphical symbols DS/EN :2014 DKK 300,00 Identisk med IEC Ed. 1:2014 og EN :2014 Halvledere - Mikroelektromekanisk udstyr - Del 22: Elektromekanisk trækprøvning af ledende tyndfilm på fleksible substrater IEC :2014 specifies a tensile test method to measure electromechanical properties of conductive thin micro-electromechanical systems (MEMS) materials bonded on non-conductive flexible substrates. Conductive thin-film structures on flexible substrates are extensively utilized in MEMS, consumer products, and flexible electronics. The electrical behaviours of films on flexible substrates differ from those of freestanding films and substrates due to their interfacial interactions. 3

6 4 Different combinations of flexible substrates and thin films often lead to various influences on the test results depending on the test conditions and the interfacial adhesion. The desired thickness of a thin MEMS material is 50 times thinner than that of the flexible substrate, whereas all other dimensions are similar to each other. Projektleder: Marianne Goor Standardisering. Generelle regler Standardization. General rules DS-listestof November 2014 DKK 170,00 Dansk Standard - Listestof November - Dansk offentliggørelse af nye standarder, forslag til standarder og nationale tekniske forskrifter - Nye udgivne standarder og forslag til høring - Nye DS-godkendte standarder fra CEN, CENELEC og ETSI - Nye harmoniserede standarder - Nye tekniske forskrifter fra EU-, EØS- og WTO-lande See Danish scope. Projektleder: Mogens Andersen Serviceydelser over for forbrugere Services for consumers DS/ISO 13687:2014 DKK 372,00 Identisk med ISO 13687:2014 Turisme og tilhørende serviceydelser - Lystbådehavne - Minimumkrav ISO 13687:2014 establishes minimum requirements for commercial and non-commercial harbours for leisure boats and yachts to deliver services to the boating community, excluding the standardization of sports activities. The scope does not cover specifics of boat yards, dry stacks, dry-docking areas, dry storages, fuel stations, and nearby beaches. Compliance with ISO 13687:2014 does not guarantee total safety or total freedom of risk in case of abnormal weather conditions above windforce 9 on the Beaufort scale and extreme sea conditions or rogue waves. Projektleder: Helle Harms Forskning og udvikling Research and development DS/EN :2014 DKK 642,00 Identisk med IEC Ed. 3:2014 og EN :2014 Ledelse af pålidelighedsaktiviteter - Del 1: Vejledning om ledelse og anvendelse This part of IEC establishes a framework for dependability management. It provides guidance on dependability management of products, systems, processes or services involving hardware, software and human aspects or any integrated combinations of these elements. It presents guidance on planning and implementation of dependability activities and technical processes throughout the life cycle taking into account other requirements such as those relating to safety and the environment. This standard gives guidelines for management and their technical personnel to assist them to optimize dependability. This standard is not intended for the purpose of certification Kvalitet. Generelt Quality in general DS/EN :2014 DKK 642,00 Identisk med IEC Ed. 3:2014 og EN :2014 Ledelse af pålidelighedsaktiviteter - Del 1: Vejledning om ledelse og anvendelse This part of IEC establishes a framework for dependability management. It provides guidance on dependability management of products, systems, processes or services involving hardware, software and human aspects or any integrated combinations of these elements. It presents guidance on planning and implementation of dependability activities and technical processes throughout the life cycle taking into account other requirements such as those relating to safety and the environment. This standard gives guidelines for management and their technical personnel to assist them to optimize dependability. This standard is not intended for the purpose of certification Fritid. Turisme Leisure. Tourism DS/ISO 13687:2014 DKK 372,00 Identisk med ISO 13687:2014 Turisme og tilhørende serviceydelser - Lystbådehavne - Minimumkrav ISO 13687:2014 establishes minimum requirements for commercial and non-commercial harbours for leisure boats and yachts to deliver services to the boating community, excluding the standardization of sports activities. The scope does not cover specifics of boat yards, dry stacks, dry-docking areas, dry storages, fuel stations, and nearby beaches. Compliance with ISO 13687:2014 does not guarantee total safety or total freedom of risk in case of abnormal weather conditions above windforce 9 on the Beaufort scale and extreme sea conditions or rogue waves. Projektleder: Helle Harms Vejtransport Road transport DSF M Svarfrist: Identisk med ISO/PRF TS og FprCEN ISO/TS Intelligente transportsystemer - Kooperative systemer - Definition af et globalt koncept for lokale dynamiske kort The scope of the work is to create an environment and the standards to implement a Local Dynamic Map (LDM) concept. The current situation is characterized that applications directly exchanging their information with the respective counterpart. Parallel applications exchanging their information in the same way. Therefore, information used by multiple applications has to be re-transmitted each time and creates a huge amount of data traffic. This leads finally to the situation where communication channels become overloaded and/or specific applications cannot be executed anymore due to the nonavailability of connection resource. The way out of this crucial situation is given if a common and coordinated local data store concept is implemented. This concept radically changes the way applications are developed and implemented. If an application is requesting information, it is requested first from the local data store, and only if the information is not available locally it is requested and transferred from the external source via the air-link. In this case, several provisions have to be given: - The access to the data base has to be unified and standardized for all applications - The data elements and its attributes used have to be harmonized and unambiguously defined - Means to maintain the content and integrity of the data store, and means to keep the content up to date have to be provided - Means to apply local regulations for privacy and security have to be developed - Last but not least the stakeholder-, userand application-requirements have to be derived and included in the development Projektleder: Carsten Riis Fredriksen DSF M Svarfrist: Identisk med pren Rumfart - Brug af geo-positionsbestemmelse til navigation og lokalisation - Del 1: Definition af MOP metode til GNSS-baseret positionerings terminaler, der benyttes i vejtransport applikationer The civil applications of geopositioning are undergoing exponential development. The latest market analysis for the GNSS systems shows 2 major fields of application which, all together, practically share the whole of the market. - Intelligent Transport Systems (ITS), mainly in the Road ITS domain. - Location Based Services (LBS), accessible on smartphones and tablets.