Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual

Størrelse: px
Starte visningen fra side:

Download "Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual"

Transkript

1 24789G-DK (rev.4) Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual Jacobsen G-Plex III Series: FH - Engine type: Kubota D722 Product code: USAD002 Series: FJ - Engine type: Briggs & Stratton Product code: USAG002 Serie: FH - Motortype: Kubota D722 Produktkode: USAD002 Serie: FJ - Motortype: Briggs & Stratton Produktkode: USAG002 WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the entire manual before attempting to set up, operate, adjust or service the machine. DK Denmark ADVARSEL: Denne maskine kan forårsage alvorlig personskade, hvis den bruges forkert. Alle, der bruger og vedligeholder denne maskine, skal være korrekt uddannet til dette, skal advares om farerne og læse hele instruktionsbogen, før maskinen forberedes, bruges, justeres eller serviceres. RJL / 100 January 2010

2 2010, Ransomes Jacobsen Limited. All Rights Reserved 2010, Ransomes Jacobsen Limited. Alle rettigheder forbeholdes

3 1 CONTENTS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL SECTION... PAGE SECTION... PAGE 2 INTRODUCTION 2.1 IMPORTANT PRODUCT IDENTIFICATION GUIDELINES FOR THE DISPOSAL OF PRODUCTS SAFETY INSTRUCTIONS 3.1 OPERATING INSTRUCTIONS SAFETY SIGNS STARTING THE ENGINE DRIVING THE MACHINE TRANSPORTING LEAVING THE DRIVING POSITION SLOPES BLOCKED CUTTING CYLINDERS ADJUSTMENTS, LUBRICATION AND MAINTENANCE SPECIFICATIONS 4.1 ENGINE SPECIFICATION MACHINE SPECIFICATION CUTTING UNIT DIMENSIONS VIBRATION LEVEL SLOPES RECOMMENDED LUBRICANTS FUEL RECOMMENDATIONS - DIESEL FUEL RECOMMENDATIONS - GASOLINE CUTTING UNIT SPECIFICATION CUTTING PERFORMANCE CONFORMITY CERTIFICATES DECALS 5.1 SAFETY DECALS INSTRUCTION DECALS CONTROLS 6.1 CONTROL PANEL - DIESEL CONTROL PANEL - GASOLINE CONTROL PEDALS PARKING BRAKE PEDAL A PARKING BRAKE LEVER PADDLE/FOOT SWITCH MOW/LIFT JOYSTICK MOW/LIFT OPERATION 7.1 DAILY INSPECTION OPERATOR PRESENCE AND SAFETY INTERLOCK SYSTEM CONTROLLER ERROR CODES OPERATING PROCEDURE MOWING PROCEDURES MOWING ON SLOPES SETUP 8.1 SET UP MOUNTING THE CUTTING HEADS REEL MOTOR MOUNTING CUTTING CYLINDER LIFT & LOWER RATE & SYNCHRONISATION LUBRICATION & MAINTENANCE 9.1 LUBRICATION AND MAINTENANCE CHART A LUBRICATION DIAGRAM - GASOLINE B LUBRICATION DIAGRAM - DIESEL ENGINE ACCESS ENGINE OIL LEVEL - GASOLINE ENGINE OIL CHANGE- GASOLINE ENGINE OIL FILTER- GASOLINE AIR FILTER - GASOLINE AIR CLEANER - GASOLINE ENGINE FUEL FILTER - GASOLINE ENGINE OIL LEVEL - DIESEL ENGINE OIL CHANGE - DIESEL ENGINE OIL FILTER - DIESEL ENGINE FUEL FILTER - DIESEL AIR FILTER - DIESEL BLEEDING THE FUEL SYSTEM - DIESEL AIR CLEANER - DIESEL FAN BELT TENSION - DIESEL TIRES BRAKES HYDRAULIC OIL FILTER HYDRAULIC OIL HYDRAULIC SYSTEM HYDRAULIC PUMP BYPASS VALVE FREE WHEELING OR TOWING UNIT BATTERY JUMP STARTING OIL COOLER GASOLINE MACHINE RADIATOR DIESEL MACHINE OIL COOLER & RADIATOR DIESEL MACHINE ADJUSTMENT 10.1 CUTTING HEAD MAINTENANCE BEDKNIFE ADJUSTMENT HEIGHT OF CUT CONTROL ARM ADJUSTMENT REAR SWING OUT ARM LEVELLING LINKAGE FOR THE FRONT CUTTING HEADS MOW/TRANSPORT SPEED CONTROL SPEED CONTROL PEDAL SEAT ADJUSTMENT LEVER BACKLAPPING SCHEMATICS 11.1 HYDRAULIC CIRCUIT ELECTRICAL CIRCUIT - GASOLINE ELECTRICAL CIRCUIT - DIESEL GUARANTEE / SALES & SERVICE Ransomes Jacobsen Limited reserves the right to make design changes without obligation to make these changes on units previously sold and the information contained in this manual is subject to change without notice. en-3

4 2 INTRODUCTION JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 2.1 IMPORTANT IMPORTANT: This is a precision machine and the service obtained from it depends on the way it is operated and maintained. This SAFETY AND OPERATORS MANUAL should be regarded as part of the machine. Suppliers of both new and second-hand machines are advised to retain documentary evidence that this manual was provided with the machine. This machine is designed solely for use in customary grass cutting operations. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer, also constitute essential elements of the intended use. Before attempting to operate this machine, ALL operators MUST read through this manual and make themselves thoroughly conversant with Safety Instructions, controls, lubrication and maintenance. Accident prevention regulations, all other generally recognized regulations on safety and occupational medicine, and all road traffic regulations shall be observed at all times. Any arbitrary modifications carried out on this machine may relieve the manufacturer of liability for any resulting damage or injury. 2006/42/EC These are the Original instructions verified by Ransomes Jacobsen Limited. 2.2 PRODUCT IDENTIFICATION A Maximum front axle load in Kg (for machines being driven on the highway) B Gross weight (mass) in Kg C Maximum rear axle load in Kg (for machines being driven on the highway) D Power in Kw E Date code F Machine type (Designation) G Product code H Product name J Serial number West Road Ransomes Europark Ipswich IP3 9TT England A B C D E Kg Kg Kg Kw F G H J Serial Plate Location The serial plate A is located on the chassis under the operators seating position. en-4

5 2 INTRODUCTION JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 2.3 GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS DURING SERVICE LIFE Used oil, oil filters and engine coolant are hazardous materials and should be handled in a safe and environmentally responsible way. In the event of a fluid leak, contain the spill to prevent it entering the ground or drainage system. Local legislation will dictate how such spills are to treated. Following the maintenance procedures laid out in this manual will ensure that the impact the machine has on the local environment is controlled. When it has been identified that a turf care product has no further functional value and requires disposal, the following actions should be taken END OF SERVICE LIFE These guidelines should be used in conjunction with applicable Health, Safety and Environmental legislation and use of approved local facilities for waste disposal and recycling. Position the machine in a suitable location for any necessary lifting equipment to be used. Use appropriate tools and Personal Protective Equipment (PPE) and take guidance from the technical manuals applicable to the machine. separated and returned to the relevant centre. Other worn out items should be separated into material groups for recycling and disposal consistent with available facilities. More common separation types are as follows: Steel Non ferrous metals Aluminium Brass Copper Plastics Identifiable Recyclable Non recyclable Not identified Rubber Electrical & Electronic Components Items that cannot be separated economically into different material groups should be added to the General waste area. Do not incinerate waste. Finally update machinery records to indicate that the machine has been taken out of service and scrapped. Provide this serial number to Jacobsen Warranty department to close off relevant records. Remove and store appropriately: 1. Batteries 2. Fuel residue 3. Engine coolant 4. Oils Disassemble the structure of the machine referring to the technical manuals where appropriate. Special attention should be made for dealing with stored energy within pressurised elements of the machine or tensioned springs. Any items that still have a useful service life as second hand components or can be re-serviced should be en-5

6 3 SAFETY INSTRUCTIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL This safety symbol indicates important safety messages in this manual. When you see this symbol, be alert to the possibility of injury, carefully read the message that follows, and inform other operators. 3.1 OPERATING INSTRUCTIONS Ensure that the instructions in this book are read and fully understood. No person should be allowed to operate this machine unless they are fully acquainted with all the controls and the safety procedures. Never allow children or people unfamiliar with these instructions to use this machine. Local regulations may restrict the age of the operator. 3.2 SAFETY SIGNS It is essential all safety labels are kept legible, if they are missing or illegible they must be replaced. If any part of the machine is replaced and it originally carried a safety label, a new label must be affixed to the replacement part. New safety labels are obtainable from Ransomes dealers. 3.3 STARTING THE ENGINE Before starting the engine check that the brakes are applied, drives are in neutral, guards are in position and intact, and bystanders are clear of the machine. Do not run the engine in a building without adequate ventilation. 3.4 DRIVING THE MACHINE Before moving the machine, check to ensure that all parts are in good working order, paying particular attention to brakes, tyres, steering and the security of cutting blades. Replace faulty silencers, mow only in daylight or good artificial light Always observe the Highway Code both on and off the roads. Keep alert and aware at all times. Watch out for traffic when crossing or near roadways. Stop the blades rotating before crossing surfaces other than grass. Remember that some people are deaf or blind and that children and animals can be unpredictable. Keep travelling speeds low enough for an emergency stop to be effective and safe at all times, in any conditions. Remove or avoid obstructions in the area to be cut, thus reducing the possibility of injury to yourself and/or bystanders. When reversing, take special care to ensure that the area behind is clear of obstructions and/or bystanders. DO NOT carry passengers. Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property. When the machine is to be parked, stored or left unattended, lower the cutting means unless the transport locks are being used. While mowing, always wear substantial footwear and long trousers. Do not operate the equipment when barefoot or wearing open sandals. Check the grass catcher frequently for wear or deterioration. After striking a foreign object. Inspect. the lawnmower for damage and make repairs before restarting and operating the equipment. If the machine starts to vibrate abnormally, check immediately. 3.5 TRANSPORTING Ensure that the cutting units are securely fastened in the transport position. Do not transport with cutting mechanism rotating. Drive the machine with due consideration of road and surface conditions, inclines and local undulations. Sudden decelerating or braking can cause the rear wheels to lift. Remember that the stability of the rear of the machine is reduced as the fuel is used. en-6

7 3 SAFETY INSTRUCTIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 3.6 LEAVING THE DRIVING POSITION Park the machine on level ground. Before leaving the driving position, stop the engine and make sure all moving parts are stationary. Apply brakes and disengage all drives. Remove the starter key. 3.7 SLOPES TAKE EXTRA CARE WHEN WORKING ON SLOPES Local undulations and sinkage will change the general slope. Avoid ground conditions which can cause the machine to slide. Keep machine speeds low on slopes and during tight turns. Sudden decelerating or braking can cause the rear wheels to lift. Remember there is no such thing as a safe slope. Travel on grass slopes requires particular care. DO NOT USE ON SLOPES GREATER THAN 15 IMPORTANT: When working on any slope set the weight transfer, if fitted to its maximum (+) setting. 3.8 BLOCKED CUTTING CYLINDERS Stop the engine and make sure all moving parts are stationary. Apply brakes and disengage all drives. Release blockages with care. Keep all parts of the body away from the cutting edge. Beware of energy in the drive which can cause rotation when the blockage is released. Keep other people away from the cutting units as rotation of one cylinder can cause the others to rotate. 3.9 ADJUSTMENTS, LUBRICATION AND MAINTENANCE Stop the engine and make sure all moving parts are stationary. Apply brakes and disengage all drives. Read all the appropriate servicing instructions. Use only the replacement parts supplied by the original manufacturer. When adjusting the cutting cylinders take care not to get hands and feet trapped when rotating cylinders. Make sure that other people are not touching any cutting units, as rotation of one cylinder can cause the others to rotate. To reduce the fire hazard, keep the engine, silencer and battery compartments free of grass, leaves or excessive grease. Replace worn or damaged parts for safety. When working underneath lifted parts or machines, make sure adequate support Is provided. Do not dismantle the machine without releasing or restraining forces which can cause parts to move suddenly. Do not alter engine speed above maximum quoted in Engine Specification. Do not change the engine governor settings or over speed the engine. Operating the engine at excessive speed may increase the hazard of personal injury. When refuelling, STOP THE ENGINE, DO NOT SMOKE. Add fuel before starting the engine, never add fuel while the engine is running. Use a funnel when pouring fuel from a can into the tank. Do not fill the fuel tank beyond the bottom of the filler neck. Replace all fuel tank and container caps securely. Store fuel in containers specifically designed for this purpose. Refuel outdoors only and do not smoke while refuelling. If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapours have dissipated. Allow the engine to cool before storing in any enclosure. Never store the equipment with fuel in the tank inside a building where fumes may reach an open flame or spark. If the fuel tank has to be drained, this should be done outdoors. Do not spill fuel onto hot components. When servicing batteries, DO NOT SMOKE, and keep naked lights away. Do not place any metal objects across the terminals. When Pressure Washing the Mower. Turn the engine off and remove the starter key. If the engine has been running, it should be allowed to cool sufficiently to prevent damage to the block and exhaust manifold. Never force water into any electrical components, the air cleaner or exhaust muffler as water could enter the engine cylinder and cause damage. en-7

8 3 SAFETY INSTRUCTIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. IMPORTANT: Transport speed is for highway use only. Never select transport speed on grass areas or uneven or unsurfaced roads or tracks. WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury and property damage. It may also be used to alert against unsafe practices. WARNING Hydraulic Fluid escaping under pressure can penetrate skin and do serious damage. Immediate medical assistance must be sought. WARNING California Proposition 65 Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California to cause cancer and birth defects or other WARNING Batteries produce explosive gases and contain corrosive acid and supply levels of electrical current high enough to cause burns. WARNING DO NOT USE ON SLOPES GREATER THAN 15 WARNING Battery posts, terminals and related accessories contain lead and lead compounds WASH HANDS AFTER HANDLING WARNING Ear Protection Should be Worn When Operating Machines with Operator Ear Noise Levels above 90dB(A)Leq. When carrying out any welding on the machine the battery and controller must be disconnected before starting. Under no circumstances should the controller be opened as this will invalidate all warranties and could result in a malfunction. en-8

9 4 SPECIFICATIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 4.1 ENGINE SPECIFICATION Speeds: TYPE:TYPE: Model: Maximum Speed: Idle Speed: Oil Sump Capacity:3.2 litres Firing Order: 1, 2, 3. Fuel: Kubota 3200 RPM, 3 cylinder Diesel engine, 4 stroke, water cooled, 719cc with 12V electric start. D722-E3B-RNUK RPM ±50 rpm (No load) 1500 RPM ±50 rpm No. 2-D Diesel fuel (ASTM D975) ENGINE SPECIFICATION Cutting: Transport: Reverse: Steering: Ground pressure: Brakes, Service: Parking: Capacities: Cooling System: 6 km/h 12 kp/h 3 kp/h Rear Wheel Steering. Power Steering, 2.5 turns lock to lock 330mm dia. Steering Wheel 1.0 kg/cm Positive hydrostatic braking. 152 mm Calliper Disk 3.8 litres TYPE:TYPE: Briggs & Stratton 3400 RPM, V twin gasoline engine, 4 stroke, air cooled, 719cc with 12V electric start. Model: Vanguard Type 1294 Maximum Speed: Idle Speed: 3400 RPM (No load) 1500 RPM Oil Sump Capacity:1.4 litres Fuel Tank: Hydraulic Tank: Total System 31 litres 18.2 litres 25.7 litres Battery: 12 volt, Type 093 Alternator 4.3 CUTTING UNIT Diesel 40 amp Gasoline 15 amp Fuel: Unleaded Gasoline Minimum 85 octane Type: Three 559mm wide steerable floating head. 4.2 MACHINE SPECIFICATION Frame construction: Heavy duty fabricated steel chassis. Transmission: Variable displacement hydrostatic pump with high speed low torque wheel motors. Cutting unit drive: Direct drive hydrostatic and reel drive pumps, bi-directional hydraulic gear motor with reel control valve and backlap control valve. Reel: 127mm diameter, 7 / 9 / 11 knife. Rolls: Bedknife to reel adjustment: Height of cut adjustment: Height of cut: Smooth rear roll, smooth or grooved front /rear rolls optional. Opposed set screw. Micro-adjusters on front roll. 2.5mm to 16mm Standard blade 2mm to 16mm Tournament blade. en-9

10 JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 4.4 DIMENSIONS A B C D Width of cut Transport width Overall height without ROPS Overall height with ROPS, add 160 cm ### cm 130 cm 42 cm E Overall Length (without Grass Boxes) F Overall Length (with Grass Boxes) 210 cm 250 cm G H J K Wheel Track Wheel Base Weight of Machine - Diesel Weight of Machine - Gasoline 120 cm 130 cm 565 kg 500 kg L Weight of Cutting Unit (each) 31.6 kg TYRE PRESSURES Product Tyre Size Tyre Type Front Wheel Tyre Pressure Tyre Size Tyre Type Rear Wheel Tyre Pressure G-Plex III 20 x Titan Smooth 2pr 9 psi 0.62 bar 20 x Titan Smooth 2pr 9 psi 0.62 bar en-10

11 4 SPECIFICATIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 4.5 VIBRATION LEVEL When the machine was tested for hand/arm vibration levels. The operator was seated in the normal operating position with both hands on the steering mechanism. The engine was running and the cutting device was rotating with the machine stationary. The Machinery Safety Directive 98/37/EC By compliance to: The Lawnmower Standard EN836:1997 Referenced to hand/arm: EN1033:1996 Information Supplied for Physical Agents Directive 2002/44/EC By reference to: Hand/Arm Standards: BS EN ISO (2001) BS EN ISO (2001) When the machine was tested for Whole Body vibration levels. The operator was seated in the normal operating position with both hands on the steering mechanism. The cutting device was rotating with the machine driven in a straight line at 6 Km/hr on a level freshly cut lawn. The Machinery Safety Directive 98/37/EC By compliance to: Whole Body EN1032:2003 Information Supplied for Physical Agents Directive 2002/44/EC By reference to: Whole Body Standards BS EN ISO (1997) Jacobsen G-Plex III Series:FH, FJ Hand / Arm Acceleration level Max LH or RH 2 Accelerations m/s Mean Value of X, Y, Z Aeq 0.50 Jacobsen G-Plex III Series:FH, FJ Whole Body Acceleration level Max LH or RH Foot 2 Accelerations m/s Mean Value of X, Y, Z Aeq 1.16 Jacobsen G-Plex III Series:FH, FJ Whole Body Acceleration level Seat Location 2 Accelerations m/s Mean Value of X, Y, Z Aeq SLOPES DO NOT USE ON SLOPES GREATER THAN 15 The slope 15 was calculated using static stability measurements according to the requirements of EN RECOMMENDED LUBRICANTS Engine oil: Diesel: Gasoline: TEMPERATURE ABOVE 4 C (39 F) SAE30 Should be to MIL-L-2104C or to A.P.I. Classification CD A.P.I. Classification SE/SF OIL VISCOSITY BELOW 4 C (39 F) SAE5W-30 or 10W-30 Hydraulic Oil: GreensCare 46 Grease: K NATE (RJL No ), or equivalent to MIL-G-23549C, MIL-G-2345C, DIN , DIN en-11

12 4 SPECIFICATIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 4.8 FUEL RECOMMENDATIONS - DIESEL Fuel tank should be filled to within 1/2", (13mm) below the bottom of the filler neck. DO NOT overfill the tank. Use #2 diesel fuel (ASTM No. 2D) when temperature is above 20 F (-7 C). Use #1 diesel fuel (ASTM No. 1D) when temperature is 20 F (-7 C) or below. NOTE NEVER use No. 2D at temperatures below 20 F (-7 C) unless you are sure it has been winterized. Cold temperatures will cause fuel to thicken which may keep your engine from running. If No. 1D is not available, a winterized blend of No. 1D and No. 2D may be available. This blended fuel is usually called No. 2D also and may be used in colder temperatures. If the vehicle fuel tank is being filled for the first time or if the vehicle was allowed to run out of fuel, it will be necessary to bleed the air from the fuel system (refer to Bleeding The Fuel System" in the Maintenance manual ). 4.9 FUEL RECOMMENDATIONS - GASOLINE Fuel tank should be filled to within 1/2, (13mm) below the bottom of the filler neck. DO NOT overfill the tank. Unleaded gasoline 87 Octane or higher We DO NOT recommend the use of ALCOHOL bearing fuels in any of our products. The use of these fuels may create a potential safety hazard. NOTE: The use of alcohol bearing fuels can cause engine malfunction, particularly "vapour lock" at temperatures above 50 F (10 c C). WARNING Gasoline containing ALCOHOL can cause deterioration of some non-metallic materials in the fuel system. Fuel hoses must be inspected frequently and replaced if excessive stiffness, deterioration or fuel leakage is found. Gasoline Containing ALCOHOL will attract and hold moisture inside fuel tanks. Moisture may cause corrosion of metallic parts within the fuel system. Fuel leakage from a fuel system can occur while the system is in use, in transit, or in storage. Such leakage can contribute to an explosion or fire, causing serious bodily injury or death CUTTING PERFORMANCE Cutting Frequency 7-knife reel - 7.4mm at 6km/h 9-knife reel - 5.7mm at 6km/h 11-knife reel - 4.7mm at 6km/h en-12

13 4 SPECIFICATIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL 4.12 CONFORMITY CERTIFICATES DECLARATION OF CONFORMITY PROHLÁŠENÍ O SHOD OVERENSSTEMMELSESERKLÆRING CONFORMITEITSVERKLARING VASTAVUSDEKLARATSIOON VAATIMUSTENMUKAISUUSVAKUUTUS DECLARATION DE CONFORMITE KONFORMITÄTSERKLÄRUNG MEGFELEL SÉGI NYILATKOZAT DICHIARAZIONE DI CONFORMITÀ ATBILST BAS DEKLAR CIJA ATITIKTIES DEKLARACIJA DIKJARAZZJONI TAL-KONFORMITÀ DEKLARACJA ZGODNO CI DECLARAÇÃO DE CONFORMIDADE DECLARA IE DE CONFORMITATE VYHLÁSENIE O ZHODE IZJAVA O SKLADNOSTI DECLARACIÓN DE CONFORMIDAD DEKLARATION OM ÖVERENSSTÄMMELSE SAMRÆMISYFIRLÝSING KONFORMITETSERKLÆRING Business name and full address of the manufacturer Obchodní jméno a plná adresa výrobce Producentens firmanavn og fulde adresse Bedrijfsnaam en volledig adres van de fabrikant Tootja ärinimi ja täielik aadress Valmistajan toiminimi ja täydellinen osoite Nom commercial et adresse compl ète du fabricant Firmenname und vollständige Adresse des Herstellers A gyártó üzleti neve és teljes címe Ragione sociale e indirizzo completo del fabbricante Uz muma nosaukums un pilna ražot ja adrese Verslo pavadinimas ir pilnas gamintojo adresas Isem kummer jali u indirizz s i tal-fabbrikant Nazwa firmy i pe ny adres producenta Nome da empresa e endereço completo do fabricante Denumirea comercial i adresa complet a produc torului Obchodný názov a úplná adresa výrobcu Naziv podjetja in polni naslov proizvajalca Nombre de la empresa y dirección completa del fabricante Tillverkarens företagsnamn och kompletta adress Fyrirt ækisheiti og fullt heimilisfang framleiðanda Firmanavn og full adresse for produsenten Ransomes Jacobsen Limited West Road, Ransomes Europark, Ipswich, England, IP3 9TT Product Code Kód výrobku Produktkode Productcode Toote kood Tuotekoodi Code produit Produktcode Termékkód Codice prodotto Produkta kods Produkto kodas Kodi i tal-prodott Kod produktu Código do Produto Cod produs Kód výrobku Oznaka proizvoda Código de producto Produktkod Vörunúmer Produktkode USAD002 USAG002 Machine Name Název stroje Maskinnavn Machinenaam Masina nimi Laitteen nimi Nom de la machine Maschinenbezeichnung Gépnév Denominazione della macchina Iek rtas nosaukums Mašinos pavadinimas Isem tal-magna Nazwa urz dzenia Nome da Máquina Numele echipamentului Názov stroja Naziv stroja Nombre de la máquina Maskinens namn Heiti t ækis Maskinnavn Jacobsen G-Plex III Designation Ozna ení Betegnelse Benaming Nimetus Tyyppimerkintä Pažym jimas Bezeichnung Megnevezés Funzione Apz m jums Lithuanian Denominazzjoni Oznaczenie Designação Specifica ie Ozna enie Namen stroja Descripción Beteckning Merking Konstruksjon Ride on Reel Mower Serial Number Sériové íslo Serienummer Serienummer Seerianumber Valmistusnumero Numéro de série Seriennummer Sorozatszám Numero di serie S rijas numurs Serijos numeris Numru Serjali Numer seryjny Número de Série Num r de serie Sériové íslo Serijska številka Número de serie Serienummer Raðnúmer Serienummer Engine Motor Motor Motor Mootor Moottori Moteur Motor Modulnév Motore Dzin js Variklis Sa a Netta Installata Silnik Motor Motor Motor Motor Motor Motor Vél Motor Net Installed Power istý instalovaný výkon Installeret nettoeffekt Netto ge ïnstalleerd vermogen Installeeritud netovõimsus Asennettu nettoteho Puissance nominale nette Installierte Nettoleistung Nettó beépített teljesítmény Potenza netta installata Paredz t t kla jauda Grynoji galia Wisa tal-qtug Moc zainstalowana netto Pot ência instalada Puterea instalat net istý inštalovaný výkon Neto vgrajena mo Potencia instalada neta Nettoeffekt Nettóafl vélar Netto installert kraft FH FH FJ FJ Kubota D722-E3B-RNUK-1 Briggs & Stratton 3Vanguard Type RPM (Kubota) RPM (Briggs & Stratton) Cutting Width Ší ka ezu Skærebredde Maaibreedte Lõikelaius Leikkuuleveys Largeur de coupe Schnittbreite Vágási szélesség Larghezza di taglio Griešanas platums Pjovimo plotis Tikkonforma mad-direttivi Szeroko ci cia Largura de Corte L imea de t iere Šírka záberu Širina reza Anchura de corte Klippbredd Skurðbreidd Klippebredde 160 cm Conforms to Directives Spl uje podmínky sm rnic Er i overensstemmelse med direktiver Voldoet aan de richtlijnen Vastab direktiividele Direktiivien mukainen Conforme aux directives Entspricht Richtlinien Megfelel az irányelveknek Conforme alle Direttive Atbilst direkt v m Atitinka direktyv reikalavimus Valutazzjoni tal-konformità Dyrektywy zwi zane Cumpre as Directivas Respect Directivele Je v súlade so smernicami Skladnost z direktivami Cumple con las Directivas Uppfyller direktiv Samr æmist tilskipunum I samsvar med direktiv 2006/42/EC 2004/108/EC 2000/14/EC Conformity Assessment Hodnocení pln ní podmínek Overensstemmelsesvurdering Conformiteitsbeoordeling Vastavushindamine Vaatimustenmukaisuuden arviointi Evaluation de conformité Konformitätsbeurteilung Megfelel ség-értékelés Valutazione della conformità Atbilst bas nov rt jums Atitikties vertinimas Livell tal-qawwa tal- oss Imkejjel Ocena zgodno ci Avaliação de Conformidade Evaluarea conformit ii Vyhodnotenie zhodnosti Ocena skladnosti Evaluación de conformidad Bedömning av överensstämmelse Samr æmismat Konformitetsvurdering 2006/42/EC Annex VIII Measured Sound Power Level Nam ený akustický výkon Målte lydstyrkeniveau Gemeten geluidsniveau Mõõdetud helivõimsuse tase Mitattu äänitehotaso Niveau de puissance sonore mesuré Gemessener Schalldruckpegel Mért hangteljesítményszint Livello di potenza sonora misurato Izm r tais ska as jaudas l menis Išmatuotas garso stiprumo lygis Livell tal-qawwa tal- oss Iggarantit Moc akustyczna mierzona Nível sonoro medido Nivelul m surat al puterii acustice Nameraná hladina akustického výkonu Izmerjena raven zvo ne mo i Nivel de potencia sonora medido Uppmätt ljudeffektsniv å Mælt hljóðaflsstig Målt lydeffektnivå 104 db(a) LWA Guaranteed Sound Power Level Garantovaný akustický výkon Garanteret lydstyrkeniveau Gegarandeerd geluidsniveau Garanteeritud helivõimsuse tase Taattu äänitehotaso Niveau de puissance sonore garanti Garantierter Schalldruckpegel Szavatolt hangteljesítményszint Livello di potenza sonora garantito Garant tais ska as jaudas l menis Garantuotas garso stiprumo lygis Livell tal-qawwa tal- oss Iggarantit Moc akustyczna gwarantowana Nível sonoro farantido Nivelul garantat al puterii acustice Garantovaná hladina akustického výkonu Zajam ena raven zvo ne mo i Nivel de potencia sonora garantizado Garanterad ljudeffektsnivå Hljóðaflsstig sem ábyrgð er tekin á Garanter lydeffektnivå 105 db(a) LWA Conformity Assessment Procedure (Noise) ( ) Postup hodnocení pln ní podmínek (hluk) Procedure for overensstemmelsesvurdering (St øj) Procedure van de conformiteitsbeoordeling (geluid) Vastavushindamismenetlus (müra) Vaatimustenmukaisuuden arviointimenettely (Melu) Procédure d évaluation de conformité (bruit) Konformitätsbeurteilungsverfahren (Geräusch) ( ) Megfelel ség-értékelési eljárás (Zaj) Procedura di valutazione della conformità (rumore) Atbilst bas nov rt juma proced ra (troksnis) Atitikties vertinimo proced ra (garsas) Pro edura tal-valutazzjoni tal-konformità ( oss) Procedura oceny zgodno ci (poziom ha asu) Processo de avaliação de conformidade (nível sonoro) Procedura de evaluare a conformit ii (zgomot) Postup vyhodnocovania zhodnosti (hluk) Postopek za ugotavljanje skladnosti (hrup) Procedimiento de evaluación de conformidad (ruido) Procedur för bedömning av överensstämmelse (buller) Samræmismatsaðferð (hávaði) Prosedyre for konformitetsvurdering (støy) 2000/14/EC Annex VI Part 1 UK Notified Body for 2000/14/EC 2000/14/ Ú ad certifikovaný podle sm rnice. 2000/14/EC Det britiske bemyndigede organ for 2001/14/EF Engels adviesorgaan voor 2000/14/EG Ühendkuningriigi teavitatud asutus direktiivi 2000/14/EÜ m õistes Direktiivin 2000/14/EY mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa Organisme notifié concernant la directive 2000/14/CE Britische benannte Stelle für 2000/14/EG 2000/14/ 2000/14/EK egyesült királyságbeli bejelentett szervezet Organismo Notificato in GB per 2000/14/CE 2000/14/EK AK re istr t organiz cija JK notifikuotosios staigos 2000/14/EC Korp Notifikat tar-renju Unit g al 2000/14/KE Dopuszczona jednostka badawcza w Wielkiej Brytanii wg 2000/14/WE Entidade notificada no Reino Unido para 2000/14/CE Organism notificat în Marea Britanie pentru 2000/14/CE Notifikovaný orgán Spojeného krá ovstva pre smernicu 2000/14/ES Britanski priglašeni organ za 2000/14/ES Cuerpo notificado en el Reino Unido para 2000/14/CE Anmält organ för 2000/14/EG i Storbritannien Tilkynntur aðili í Bretlandi fyrir 2000/14/EC Britisk teknisk for 2000/14/EF Number: 1088 Sound Research Laboratories Limited Holbrook House, Little Waldingfield Sudbury, Suffolk CO10 0TH en-13

14 4 SPECIFICATIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL Operator Ear Noise Level Hladina hluku v oblasti uší operátora Støjniveau i førers ørehøjde Geluidsniveau oor bestuurder Müratase operaatori kõrvas Melutaso käyttäjän korvan kohdalla Niveau de bruit à hauteur des oreilles de l opérateur Schallpegel am Bedienerohr A kezel fülénél mért zajszint Livello di potenza sonora all orecchio dell operatore Trokš a l menis pie operatora auss Dirban iojo su mašina patiriamo triukšmo lygis Livell tal- oss fil-widna tal-operatur Dopuszczalny poziom ha asu dla operatora Nível sonoro nos ouvidos do operador Nivelul zgomotului la urechea operatorului Hladina hluku pôsobiaca na sluch operátora Raven hrupa pri ušesu upravljavca Nivel sonoro en el oído del operador Ljudnivå vid förarens öra Hávaðastig fyrir stjórnanda Støynivå ved operatørens øre 85 db(a) Leq (2006/42/EC) Harmonised standards used Použité harmonizované normy Brugte harmoniserede standarder Gebruikte geharmoniseerde standaards Kasutatud ühtlustatud standardid Käytetyt yhdenmukaistetut standardit Normes harmonisées utilisées Angewandte harmonisierte Normen Harmonizált szabványok Standard armonizzati applicati Izmantotie saska otie standarti Panaudoti suderinti standartai Standards armonizzati u ati Normy spójne powi zane Normas harmonizadas usadas Standardele armonizate utilizate Použité harmonizované normy Uporabljeni usklajeni standardi Estándares armonizados utilizados Harmoniserade standarder som används EN :2005 EN :2007 EN :1992 EN :1995 EN ISO 3744:1995 EN ISO 3746:1995 ISO 5349:1986 ISO :1985 EN 836:1987 EN ISO 14982:1998 Technical standards and specifications used Použité technické normy a specifikace Brugte tekniske standarder og specifikationer Gebruikte technische standaards en specificaties Kasutatud tehnilised standardid ja spetsifikatsioonid Käytetyt tekniset standardit ja eritelmät Spécifications et normes techniques utilisées Angewandte technische Normen und Spezifikationen M szaki szabványok és specifikációk Standard tecnici e specifiche applicati Izmantotie tehniskie standarti un specifik cijas Panaudoti techniniai standartai ir technin informacija Standards u spe ifikazzjonijiet tekni i u ati Normy i specyfikacje techniczne powi zane Normas técnicas e especificações usadas Standardele tehnice i specifica iile utilizate Použité technické normy a špecifikácie Uporabljeni tehni ni standardi in specifikacije Estándares y especificaciones técnicas utilizadas Tekniska standarder och specifikationer som används Samr æmdir staðlar sem notaðir eru Benyttede harmoniserte standarder BS BS EN 1033:1996 BS EN 1032:2003 The place and date of the declaration Místo a datum prohlášení Sted og dato for erkl æringen Plaats en datum van de verklaring Deklaratsiooni väljastamise koht ja kuupäev Vakuutuksen paikka ja päivämäärä Lieu et date de la déclaration Ort und Datum der Erklärung A nyilatkozat kelte (hely és id ) Luogo e data della dichiarazione Deklar cijas vieta un datums Deklaracijos vieta ir data Il-post u d-data tad-dikjarazzjoni Miejsce i data wystawienia deklaracji Local e data da declaração Locul i data declara iei Miesto a dátum vyhlásenia Kraj in datum izjave Lugar y fecha de la declaración Plats och datum för deklarationen T æknistaðlar og tæknilýsingar sem notaðar eru Benyttede tekniske standarder og spesifikasjoner Staður og dagsetning yfirlýsingar Sted og dato for erklæringen Ransomes Jacobsen Limited West Road, Ransomes Europark, Ipswich, England, IP3 9TT 4th January 2010 Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to compile the technical file, and who is established in the Community.,,. Podpis osoby oprávn né sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávn né sestavit technické soubory a založené v rámci Evropského spole enství. Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver af dokumentationen og er bemyndiget til at udarbejde den tekniske journal, og som er baseret i nærområdet. Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische documentatie bewaart en bevoegd is om het technische bestand samen te stellen, en die is gevestigd in het Woongebied. Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist dokumentatsiooni ja kellel on õigus koostada tehniline toimik. Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset asiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on sijoittautunut yhteisöön. Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation technique, à compiler les fichiers techniques et qui est implantée dans la Communauté. Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die technischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen zusammenzustellen, und die in der Gemeinschaft niedergelassen ist.,. A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a m szaki dokumentációt rzi, engedéllyel rendelkezik a m szaki fájl összeállításához, és aki a közösségben letelepedett személy. Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della documentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve essere stabilita nella Comunità. T s personas paraksts, kura ir pilnvarota deklar cijas sast d šanai ražot ja v rd, kurai ir tehnisk dokument cija, kura ir pilnvarota sagatavot tehnisko re istru un kura ir apstiprin ta Kopien. Asmuo, kuris yra gana žinomas, kuriam gamintojas suteik galiojimus sudaryti ši deklaracij, ir kuris j pasiraš, turi vis technin informacij ir yra galiotas sudaryti technin s informacijos dokument. Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f isem il-fabbrikant, g andha d-dokumentazzjoni teknika u hija awtorizzata li tikkompila l-fajl tekniku u li hija stabbilita fil-komunità. Podpis osoby upowa nionej do sporz dzenia deklaracji w imieniu producenta, przechowuj cej dokumentacj techniczn, upowa nion do stworzenia dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych. Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação técnica, que está autorizada a compilar o processo técnico e que está estabelecida na Comunidade. Semn tura persoanei împuternicite s elaboreze declara ia în numele produc torului, care de ine documenta ia tehnic, este autorizat s compileze dosarul tehnic i este stabilit în Comunitate. Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je oprávnená spracova technické podklady a ktorá je umiestnená v Spolo enstve. Podpis osebe, pooblaš ene za izdelavo izjave v imenu proizvajalca, ki ima tehni no dokumentacijo in lahko sestavlja spis tehni ne dokumentacije, ter ima sedež v Skupnosti. Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica y está autorizada para recopilar el archivo técnico y que está establecido en la Comunidad. Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska dokumentationen och är bemyndigad att sammanställa den tekniska informationen och som är etablerad i gemenskapen. Undirskrift aðilans sem hefur umboð til að gera yfirlýsinguna fyrir hönd framleiðandans, hefur undir höndum tæknigögnin og hefur leyfi til að taka saman tækniskýrsluna, og er viðurkenndur innan evrópska efnahagssvæðisins. Signaturen til personen som har fullmakt til å utferdige erklæringen på vegne av produsenten, er i besittelse av den tekniske dokumentasjonen, har autorisasjon til å utarbeide den tekniske filen og som har tilhold i EU. Tim Lansdell Technical Director 4th January 2010 Ransomes Jacobsen Limited West Road, Ransomes Europark, Ipswich, England, IP3 9TT Certificate Number íslo osv d ení Certifikatnummer Certificaatnummer Sertifikaadi number Hyväksyntänumero Numéro de certificat Bescheinigungsnummer Hitelesítési szám Numero del certificato Sertifik ta numurs Sertifikato numeris Numru ta - ertifikat Numer certyfikatu Número do Certificado Num r certificat íslo osved enia Številka certifikata Número de certificado Certifikatsnummer Númer skírteinis Sertifikatnummer (Rev.5) en-14

15 4 SPECIFICATIONS JACOBSEN G-PLEX III Series: FH & FJ SAFETY AND OPERATORS MANUAL DECLARATION OF INCORPORATION PROHLÁŠENÍ O ZALOŽENÍ SPOLE NOSTI INKORPORERINGSERKLÆRING INCORPORATIEVERKLARING KINNITUS ÜHENDAMISE KOHTA ASENNUSTODISTUS DECLARATION D INCORPORATION EINBAUBESCHEINIGUNG BEÉPÍTÉSI NYILATKOZAT DICHIARAZIONE DI INCORPORAZIONE NOFORM ŠANAS DEKLAR CIJA PRIJUNGIMO DEKLARACIJA DIKJARAZZJONI TA INKORPORAZZJONI DEKLARACJA ZGODNO CI DLA PODZESPO U DECLARAÇÃO DE INCORPORAÇÃO DECLARA IE DE ÎNCORPORARE VYHLÁSENIE O ZABUDOVANÍ SÚ ASTI IZJAVA ZA VGRADNJO DECLARACIÓN DE INCORPORACIÓN INBYGGNADSDEKLARATION YFIRLÝSING UM ÍSETNINGU PRODUSENTENS ERKLÆRING Business name and full address of the manufacturer Obchodní jméno a plná adresa výrobce Producentens firmanavn og fulde adresse Bedrijfsnaam en volledig adres van de fabrikant Tootja ärinimi ja täielik aadress Valmistajan toiminimi ja täydellinen osoite Nom commercial et adresse complète du fabricant Firmenname und vollständige Adresse des Herstellers A gyártó üzleti neve és teljes címe Ragione sociale e indirizzo completo del fabbricante Uz muma nosaukums un pilna ražot ja adrese Verslo pavadinimas ir pilnas gamintojo adresas Isem kummer jali u indirizz s i tal-fabbrikant Nazwa firmy i pe ny adres producenta Nome da empresa e endereço completo do fabricante Denumirea comercial i adresa complet a produc torului Obchodný názov a úplná adresa výrobcu Naziv podjetja in polni naslov proizvajalca Nombre de la empresa y dirección completa del fabricante Tillverkarens företagsnamn och kompletta adress Fyrirtækisheiti og fullt heimilisfang framleiðanda. Firmanavn og full adresse for produsenten. Product Code Serial Number Description ## Cutting Unit, 11 blade, Greens ## Cutting Unit, 9 blade, Greens ## Cutting Unit, 7 blade, tees ## Cutting Unit, Verticut Ransomes Jacobsen Limited West Road, Ransomes Europark, Ipswich, England, IP3 9TT Description and identification of the partly completed machinery.. Popis a identifikace áste n dokon eného strojního za ízení. Beskrivelse og identifikation af den delvist fremstillede maskine. Beschrijving en identificatie van de gedeeltelijk voltooide machinerie. Osaliselt komplekteeritud masina kirjeldus ja määratlus. Osittain kootun laitteiston kuvaus ja määrittely. Description et identification de la quasi-machine. Bezeichnung und Identifizierung der teilgefertigten Vorrichtung. A részlegesen megépített gép leírása és meghatározása. Descrizione e identificazione della quasi-macchina Da ji pabeigtas iek rtas apraksts un identifik cija. Dalinai užbaigtos rangos aprašymas ir identifikacija. Deskrizzjoni u identifikazzjoni tal-makkinarju li jkun lest parzjalment. Opis i oznaczenie cz ciowo uko czonego urz dzenia Descrição e identificação do equipamento parcial Descrierea i identificarea echipamentului finalizat par ial Opis a identifikácia podzostavy strojného zariadenia Opis in identifikacija delno dokon anega stroja. Descripción e identificación de la maquinaria parcialmente completada. Beskrivning och identifiering av maskindelarna. Fyrirtækisheiti og fullt heimilisfang framleiðanda. Lýsing og auðkenni hálfsamsetta vélbúnaðarins. Erklæring og identifikasjon for det delvis ferdigstilte maskineriet. We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery. This shall be by hardcopy and shall be without prejudice to the intellectual property rights of the manufacturer of the partly completed machinery.,,.. Zavazujeme se na základ zd vodn né žádosti ze strany národních ú ad poskytnout p íslušné informace o áste n dokon eném strojním za ízení. Informace budou p edány v tišt né podob a nepoškodí práva k duševnímu vlastnictví výrobce týkající se áste n dokon eného strojního za ízení. Som svar på en begrundet anmodning fra de nationale myndigheder forpligter vi os til at videregive oplysninger om den delvist fremstillede maskine. Dette bliver gjort i papirudgave og med forbehold for de immaterielle rettigheder, som indehaves af producenten af den delvist fremstillede maskine. We zijn van plan, in reactie op een redelijk verzoek van de nationale autoriteiten, relevante informatie over de gedeeltelijk voltooide machinerie te verzenden. Dit wordt gedaan in de vorm van fysieke kopieën en deze kopieën zullen onder alle voorbehoud behoren tot de intellectuele eigendomsrechten van de fabrikant van de gedeeltelijk voltooide machinerie. Me kohustume riigisiseste asutuste põhjendatud nõudmisel edastama asjakohast teavet osaliselt komplekteeritud masina kohta. Andmed edastatakse paberkandjal ning sellega ei tohi piirata osaliselt komplekteeritud masina tootja õigusi intellektuaalsele omandile. Sitoudumme toimittamaan osittain koottua laitteistoa koskevat olennaiset tiedot vastineena kansallisten viranomaisten perusteltuun pyyntöön. Tiedot toimitetaan paperitulosteena. Ne eivät rajoita valmistajan osittain koottua laitteistoa koskevia immateriaalioikeuksia. Nous nous engageons à fournir, en réponse à une demande rationnelle des autorités nationales, toute information appropriée concernant la quasi-machine. Ceci se fera par copie papier et sans préjuger des droits de propriété intellectuelle du fabricant de la quasi-machine. Wir verpflichten uns, auf eine begründete Aufforderung durch die nationalen Behörden hin, relevante Informationen über die teilgefertigte Maschine zu übersenden. Diese werden als Ausdruck übersandt und dürfen sich nicht nachteilig auf die Rechte am geistigen Eigentum des Herstellers der teilgefertigten Maschine auswirken.,,.. Vállaljuk, hogy átadjuk a nemzeti hatóságok megalapozott kérésére válaszul a részlegesen megépített gépre vonatkozó információkat. Az információkat nyomtatott példányban adjuk át. A nyomtatott példány átadása a részlegesen megépített gép gyártójának szellemi tulajdonjogaira tett kötelezettség nélkül történik. Ci impegniamo a trasmettere, in risposta ad una richiesta adeguatamente motivata delle autorità nazionali, informazioni pertinenti sulla quasi-macchina. L impegno sarà redatto in forma cartacea e lascerà impregiudicati i diritti di proprietà intellettuale del fabbricante della quasi-macchina. Atsaucoties uz pamatotu valsts iest žu piepras jumu, m s ap emamies nodot saist to inform ciju par da ji pabeigtu iek rtu. T b s ciet kopija un nerad s kait jumus da ji pabeigt s iek rtas ražot ja intelektu l pašuma ties b m. Atsakydami nacionalini valdžios organ užklaus, pateikiame informacij apie dalinai užbaigtus mechanizmus. Šis dokumentas yra atspausdintas elektroninio originalo variantas ir be jokio išankstinio nusistatymo neturi tikslo pažeisti dalinai užbaigto mechanizmo gamintojo intelektualin s nuosavyb s teisi. A na nwieg du li nippre entaw, meta mitlubin mill-awtoritajiet nazzjonali, l-informazzjoni relevanti dwar il-makkinarju li jkun lest parzjalment. Din l-informazzjoni g andha tkun f forma stampata u ming ajr pre udizzju g ad-drittijiet tal-proprjetà intelletwali tal-fabbrikant tal-makkinarju li jkun lest parzjalment. Na uzasadnion pro b instytucji pa stwowych zobowi zujemy si do przekazania wszelkich informacji na temat cz ciowo uko czonego urz dzenia. B d one przekazane na pi mie. Strona przekazuj ca w/wym. dokumentacj nie b dzie ro ci a sobie adnych praw do w asno ci intelektualnej producenta cz ciowo uko czonego urz dzenia. Na sequência de pedido razoável por parte das autoridades nacionais, comprometemo-nos a transmitir informações importantes sobre o equipamento parcial. Tal será feito por meio de hardcopy e sem prejuízo para os direitos de propriedade intelectual do fabricante do equipamento parcial. Ne angaj m s transmitem, ca r spuns la o solicitare motivat a autorit ilor na ionale, informa ii relevante privind echipamentul finalizat par ial. Aceasta se va efectua în format hârtie i f r a aduce atingere drepturilor de proprietate intelectual ale produc torului echipamentului finalizat par ial. Zaväzujeme sa, že na základe odôvodnenej požiadavky národných orgánov predložíme dôležité informácie o podzostave strojného zariadenia. Musí to by v tla enej forme a bez ujmy na právach duševného vlastníctva výrobcu podzostavy strojného zariadenia. Zavezujemo se, da bomo na utemeljeno zahtevo nacionalnih organov predložili zadevne informacije o delno dokon anem stroju. Informacije bodo v tiskani obliki in ne bodo posegale v pravice intelektualne lastnine proizvajalca delno dokon anega stroja. Nos comprometemos a transmitir, en respuesta a una petición razonada por parte de las autoridades nacionales, información relevante sobre la maquinaria parcialmente completada. Ésta será transmitida en copia impresa y no afectará a los derechos de propiedad intelectual del fabricante de la maquinaria parcialmente completada. Vi åtar oss att vidarebefordra relevant information om maskindelarna vid en motiverad förfrågan från nationella myndigheter. Informationen ska erhållas i form av papperskopior och ska vara utan men för maskindelstillverkarens immateriella rättigheter. Berist okkur rökstudd beiðni frá landsyfirvöldum um að senda mikilvægar upplýsingar um hálfsamsetta vélbúnaðinn, munum við verða við slíkri beiðni. Beiðnin skal vera í prentriti og gilda með fyrirvara um hugverkarétt framleiðanda hálfsamsetta vélbúnaðarins. Vi vil, på anmodning fra nasjonale myndigheter, formidle all relevant informasjon om det delvis ferdigstilte maskineriet. Informasjonen vil bli formidlet i papirutgave og skal være uten prejudise for åndsrettighetene til produsenten av det delvis ferdigstilte maskineriet. en-15

frame bracket Ford & Dodge

frame bracket Ford & Dodge , Rev 3 02/19 frame bracket 8552005 Ford & Dodge ITEM PART # QTY DESCRIPTION 1 00083 8 NUT,.50NC HEX 2 00084 8 WASHER,.50 LOCK 3 14189-76 2 FRAME BRACKET 4 14194-76 1 411AL FRAME BRACKET PASSENGER SIDE

Læs mere

lindab we simplify construction

lindab we simplify construction lindab we simplify construction Declaration of incorporation of partly completed machinery Försäkran för inbyggnad av en delvis fullbordad maskin Inkorporeringserklæring for delmaskine Erklärung für den

Læs mere

Safety Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual

Safety Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual 24684G-DK (rev.4) Safety Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual Ransomes HR6010 Jacobsen Euro HR6010 Series: EA - Engine type: Perkins 404-22T Product codes:

Læs mere

Engine Powered Forklift ton

Engine Powered Forklift ton Engine Powered Forklift 1. - 7.0 ton 8FGCU1-30 8FGC3U-70U www.toyota-forklifts. Engine Powered Forklift 1. - 1.7 tonne Truck specifications 8FGCU1 8FGCU18 1.1 Manufacturer TOYOTA TOYOTA 1.2 Model 8FGCU1

Læs mere

Manual Transmission Remove and Install (2,0 DOHC 8V Engine) ( ) Remove

Manual Transmission Remove and Install (2,0 DOHC 8V Engine) ( ) Remove Manual Transmission Remove and Install (,0 DOHC 8V Engine) (6 4 0) Workshop Equipment Transmission jack Materials Brake fluid (Super Dot 4) ESD-M6C57-A Remove. Standard preparatory measures: Make a note

Læs mere

Sikkerhedsvejledning

Sikkerhedsvejledning 11-01-2018 2 Sikkerhedsvejledning VIGTIGT! Venligst læs disse instruktioner inden sengen samles og tages i brug Tjek at alle dele og komponenter er til stede som angivet i vejledningen Fjern alle beslagsdele

Læs mere

INSTALLATION INSTRUCTIONS STILLEN FRONT BRAKE COOLING DUCTS NISSAN 370Z P/N /308960!

INSTALLATION INSTRUCTIONS STILLEN FRONT BRAKE COOLING DUCTS NISSAN 370Z P/N /308960! Materials supplied: 1. (10) Zip Ties 2. (4) Hose Clamps 3. (2) Brake Duct Hose 4. (2) Brake Shields 5. (2) Front Brake Ducts ( Stock Fascia Only ) 6. (2) Washers 1 OD ( Stock Fascia Only ) 7. (8) Shims

Læs mere

RPW This app is optimized for: For a full list of compatible phones please visit radiation. result.

RPW This app is optimized for: For a full list of compatible phones please visit   radiation. result. TM TM RPW-1000 Laser Distance Measurer This app is optimized for: For a full list of compatible phones please visit www.ryobitools.eu/phoneworks IMPORTANT SAFETY S READ AND UNDERSTAND ALL INSTRUCTIONS.

Læs mere

Safety, Operation & Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesvejledning

Safety, Operation & Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesvejledning 23910G-DK (rev.3) Safety, Operation & Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesvejledning Ransomes Mounted Hydraulic 5 Reel Mower Ransomes Mounted Hydraulic 5 plæneklipper med knivcylindre

Læs mere

TGP 15 H. Betjeningsvejledning. Texas Power Line Pumper 2003 / 2

TGP 15 H. Betjeningsvejledning. Texas Power Line Pumper 2003 / 2 2003 / 2 Betjeningsvejledning Texas Power Line Pumper TGP 15 H Texas Andreas Petersen A/S Knullen 2 DK-5260 Odense S Tlf. 6395 5555 Fax 6395 5558 post@texas.dk - www.texas.dk ADVARSEL - Læs altid betjeningsvejledningen

Læs mere

Engine powered forklift tonne

Engine powered forklift tonne www.toyota-forklifts. Engine powered forklift 1.5-3.5 tonne Engine powered forklift 1.5-1.75 tonne Truck specifications 02-8FGF15 02-8FDF15 02-8FGF18 02-8FDF18 1.1 Manufacturer TOYOTA TOYOTA TOYOTA TOYOTA

Læs mere

Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual

Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual 24731G-DK (rev.4) Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual Jacobsen TR3 Series: EJ - 26" Cutting Units - Engine type: Kubota D1105-E - Product code: TR30001

Læs mere

DANSK INSTALLATIONSVEJLEDNING VLMT500 ADVARSEL!

DANSK INSTALLATIONSVEJLEDNING VLMT500 ADVARSEL! DANSK INSTALLATIONSVEJLEDNING VLMT500 Udpakningsinstruktioner Åben indpakningen forsigtigt og læg indholdet på et stykke pap eller en anden beskyttende overflade for at undgå beskadigelse. Kontroller at

Læs mere

Brugsanvisning. Installation Manual

Brugsanvisning. Installation Manual Manual size: 148 x 210 mm 175g copper paper(铜版纸印刷) UNIVERSAL BIL TAGBAGAGEBÆRER Brugsanvisning UNIVERSAL CAR ROOF RACK Installation Manual Model no. 10889 Tak fordi du valgte dette produkt, som vi håber

Læs mere

Varenr.: 553925 90 højre 553926 90 venstre 554027 90º højre med coating 554028 90º venstre med coating

Varenr.: 553925 90 højre 553926 90 venstre 554027 90º højre med coating 554028 90º venstre med coating DK GH Skiftespor Varenr.: 55395 90 højre 55396 90 venstre 55407 90º højre med coating 55408 90º venstre med coating 553991 60º højre 553995 60º venstre 551058 60º højre med coating 551059 60º venstre med

Læs mere

Project Step 7. Behavioral modeling of a dual ported register set. 1/8/ L11 Project Step 5 Copyright Joanne DeGroat, ECE, OSU 1

Project Step 7. Behavioral modeling of a dual ported register set. 1/8/ L11 Project Step 5 Copyright Joanne DeGroat, ECE, OSU 1 Project Step 7 Behavioral modeling of a dual ported register set. Copyright 2006 - Joanne DeGroat, ECE, OSU 1 The register set Register set specifications 16 dual ported registers each with 16- bit words

Læs mere

Sikkerheds-, betjenings- og vedligeholdelsesmanual. Commander 3520

Sikkerheds-, betjenings- og vedligeholdelsesmanual. Commander 3520 24345G-DK (rev.6) Safety, Operation & Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual Series: GC Product code: LGTT020 Commander 3520 Serie: GC Produktkode: LGTT020 WARNING: If incorrectly

Læs mere

ATEX direktivet. Vedligeholdelse af ATEX certifikater mv. Steen Christensen stec@teknologisk.dk www.atexdirektivet.

ATEX direktivet. Vedligeholdelse af ATEX certifikater mv. Steen Christensen stec@teknologisk.dk www.atexdirektivet. ATEX direktivet Vedligeholdelse af ATEX certifikater mv. Steen Christensen stec@teknologisk.dk www.atexdirektivet.dk tlf: 7220 2693 Vedligeholdelse af Certifikater / tekniske dossier / overensstemmelseserklæringen.

Læs mere

Montage bjælkeklipper BM 5001R Art. No. 112870. Assembly scythe mower BM 5001R Art. No. 112870

Montage bjælkeklipper BM 5001R Art. No. 112870. Assembly scythe mower BM 5001R Art. No. 112870 Montage bjælkeklipper BM 5001R Art. No. 112870 Assembly scythe mower BM 5001R Art. No. 112870 Løsdele pose pakket, afdækninger, skaftkonsol, skaft højre og venstre. Lose parts plastic bag, covers, handle

Læs mere

ROTERENDE TABURET 360 GRADER MED HYL Brugsanvisning. ROTATING SHOWER STOOL WITH TRAY Installation Manual. Size: 148 x 210 mm 105g copper paper

ROTERENDE TABURET 360 GRADER MED HYL Brugsanvisning. ROTATING SHOWER STOOL WITH TRAY Installation Manual. Size: 148 x 210 mm 105g copper paper Size: 148 x 210 mm 105g copper paper ROTERENDE TABURET 360 GRADER MED HYL Brugsanvisning ROTATING SHOWER STOOL WITH TRAY Installation Manual Model. 10853 1. Fjern emballagen. 2. Taburettens ben samles

Læs mere

UNISONIC TECHNOLOGIES CO.,

UNISONIC TECHNOLOGIES CO., UNISONIC TECHNOLOGIES CO., 3 TERMINAL 1A NEGATIVE VOLTAGE REGULATOR DESCRIPTION 1 TO-263 The UTC series of three-terminal negative regulators are available in TO-263 package and with several fixed output

Læs mere

Diamond Core Drilling

Diamond Core Drilling Diamond Core Drill ZIZ-250Pro Product Description Diamond core drill is a tool used for drilling holes on reinforced concrete, rocks and fire-proof materials. It features in high-efficiency, smooth and

Læs mere

PEMS RDE Workshop. AVL M.O.V.E Integrative Mobile Vehicle Evaluation

PEMS RDE Workshop. AVL M.O.V.E Integrative Mobile Vehicle Evaluation PEMS RDE Workshop AVL M.O.V.E Integrative Mobile Vehicle Evaluation NEW - M.O.V.E Mobile Testing Platform Key Requirements for Measuring Systems Robustness Shock / vibrations Change of environment Compact

Læs mere

SAF Brake Cylinders for disc brakes. Installation and Service Guide

SAF Brake Cylinders for disc brakes. Installation and Service Guide SAF Brake Cylinders for disc brakes Contents Contents... 1 Safety Information... 2 Installation of the SAF Brake Cylinders... 3 Installation of the Single Diaphragm Cylinder... 3 Installation of the Double

Læs mere

Montage bjælkeklipper BM 870 III Art. No / BM 875 III Art. No

Montage bjælkeklipper BM 870 III Art. No / BM 875 III Art. No Montage bjælkeklipper BM 870 III Art. No. 112871 / BM 875 III Art. No. 112872 Assembly scythe mower BM 870 III Art. No. 112871 / BM 875 III Art. No. 112872 Motor og driv enhed. Engine and drive unit. Løsdele

Læs mere

XXL-Rehab Stok XXL-Rehab Walking Cane

XXL-Rehab Stok XXL-Rehab Walking Cane XXL-Rehab Stok XXL-Rehab Walking Cane Anvendelse Use Max 270 kg Brugsanvisning User manual DK Bruges til: - Bariatriske brugere. UK For use by: - Bariatric users. Brugsanvisning for XXL-Rehab Stok ADVARSEL

Læs mere

Assembly Instructions. ROLZ-2 Portable AV/Conference Center

Assembly Instructions. ROLZ-2 Portable AV/Conference Center 1 Assembly Instructions ROLZ-2 Portable AV/Conference Center Rolz-2 Portable AV/Conference Center Part Drawing Description Qty Part Drawing Description Qty Hardware List A 1 ½ Flat Head Screw 2 EA P-1

Læs mere

XXL-Rehab 4-punkt Stok XXL-Rehab 4-point Cane

XXL-Rehab 4-punkt Stok XXL-Rehab 4-point Cane XXL-Rehab 4-punkt Stok XXL-Rehab 4-point Cane Anvendelse Use Max 270 kg Brugsanvisning User manual DK Kan med fordel anvendes til: - Bariatriske brugere. UK Ideal use for: - Bariatric users. Brugsanvisning

Læs mere

XXL-Rehab 4-punkt Stok XXL-Rehab 4-point Cane

XXL-Rehab 4-punkt Stok XXL-Rehab 4-point Cane XXL-Rehab 4-punkt Stok XXL-Rehab 4-point Cane Anvendelse Use Max 270 kg Brugsanvisning User manual DK Bruges til: - Bariatriske brugere. UK For use by: - Bariatric users. Brugsanvisning for XXL-Rehab 4-punkt

Læs mere

Special VFR. - ved flyvning til mindre flyveplads uden tårnkontrol som ligger indenfor en kontrolzone

Special VFR. - ved flyvning til mindre flyveplads uden tårnkontrol som ligger indenfor en kontrolzone Special VFR - ved flyvning til mindre flyveplads uden tårnkontrol som ligger indenfor en kontrolzone SERA.5005 Visual flight rules (a) Except when operating as a special VFR flight, VFR flights shall be

Læs mere

Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual

Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual 24715G-DK (rev.4) Safety, Operation and Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesmanual Jacobsen AR3 Series: EK Product code: AR30001 Series: FZ Product code: AR30002 Series: GX Product

Læs mere

Recall information fra C. Reinhardt

Recall information fra C. Reinhardt Ballerup, den 19. januar 2016 Recall information fra C. Reinhardt Kære alle Vi har modtaget en recall fra Suzuki Global. I dette brev kan du læse de vigtigste punkter vedrørende problemerne og hvordan

Læs mere

Model Brugsanvisning Instruction manual

Model Brugsanvisning Instruction manual Model 11560 Brugsanvisning Instruction manual DK GB CAMPINGTOILET Dele Toiletlåg Toiletsæde Vandpåfyldningsstuds Pumpestempel Låsebeslag 10 liters skylletank Tømmetud Skyderventil Niveauindikator 20 liters

Læs mere

Constant Terminal Voltage. Industry Workshop 1 st November 2013

Constant Terminal Voltage. Industry Workshop 1 st November 2013 Constant Terminal Voltage Industry Workshop 1 st November 2013 Covering; Reactive Power & Voltage Requirements for Synchronous Generators and how the requirements are delivered Other countries - A different

Læs mere

VACUUM PRESSURE REGULATOR

VACUUM PRESSURE REGULATOR VUUM PRESSURE REGULTOR DESRIPTION PRESSURE RNGE ONNETION SERIES PGE max. 22 l/min miniature -850 0 mbar 1 8 NPT V800.02 max. 22 l/min miniature -850 0 mbar 10-32 and flange V900.02 max. 0 l/min precise

Læs mere

Safety, Operation & Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesvejledning

Safety, Operation & Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesvejledning 24036G-DK (rev.4) Safety, Operation & Maintenance Manual Sikkerheds-, betjenings- og vedligeholdelsesvejledning Ransomes Hydraulic TG3400 & TG4650 Series: UC Hydraulic 3400 with 6 knife fixed head Magna

Læs mere

DIVAR VIGTIGT! / IMPORTANT! MÅL / DIMENSIONS. The DIVAR wall lamp comes standard. with 2.4 m braided cord and a plug in power supply (EU or UK).

DIVAR VIGTIGT! / IMPORTANT! MÅL / DIMENSIONS. The DIVAR wall lamp comes standard. with 2.4 m braided cord and a plug in power supply (EU or UK). DIVAR VIGTIGT! / IMPORTANT! VIGTIGT læs vores anvisninger før du bruger produktet. Har du problemer med den elektriske installation, skal du kontakte en elektriker. Sørg for at altid slukke for strømmen

Læs mere

Slot diffusers. Slot diffusers LD-17, LD-18

Slot diffusers. Slot diffusers LD-17, LD-18 LD-17, LD-18 Application LD-17 and LD-18 are designed for supply of cold or warm air in rooms with a height between. m and 4 m. They allow easy setting of air deflectors for different modes of operation

Læs mere

Unitel EDI MT940 June 2010. Based on: SWIFT Standards - Category 9 MT940 Customer Statement Message (January 2004)

Unitel EDI MT940 June 2010. Based on: SWIFT Standards - Category 9 MT940 Customer Statement Message (January 2004) Unitel EDI MT940 June 2010 Based on: SWIFT Standards - Category 9 MT940 Customer Statement Message (January 2004) Contents 1. Introduction...3 2. General...3 3. Description of the MT940 message...3 3.1.

Læs mere

SPARE PARTS LIST. RIDERS R316 TXs AWD, , , 2012

SPARE PARTS LIST. RIDERS R316 TXs AWD, , , 2012 SPARE PARTS LIST RIDERS R316 TXs AWD, 966757801, 967152101, 2012 103CM CUTTING DECK R316 TXs AWD, 966757801, 967152101, 2012 103CM CUTTING DECK R316 TXs AWD, 966757801, 967152101, 2012 Ref Part No Description

Læs mere

PILLE PRESSE. 1 of 8. Salg & Service PE Maskiner Ans ApS Søgade 9 DK-8643 Ans By Tlf. +45 8687 0535 Fax +45 8687 0776 www.pemaskiner.

PILLE PRESSE. 1 of 8. Salg & Service PE Maskiner Ans ApS Søgade 9 DK-8643 Ans By Tlf. +45 8687 0535 Fax +45 8687 0776 www.pemaskiner. PILLE PRESSE Lav dine egne piller! N-MICRO pellet machine is the easiest way to Pellet. N-MICRO has been projected and developed properly for home and small pellet production, so every carpenter, farmer

Læs mere

Parts catalogue Rabbit Mower

Parts catalogue Rabbit Mower OREC ISSUED NO. RM97EU-1 Parts catalogue Rabbit Mower (EXPORT MODEL) RM97 MODEL CODE RM97 0292- CONTENTS FRAME 1-12 TRANSMISSION 13-21 HST 22-23 HANDLE 24-26 FRONT 27-30 CONTROL 31-35 CUTTING 36-42 SEAT

Læs mere

DIVAR VIGTIGT! / IMPORTANT! MÅL / DIMENSIONS

DIVAR VIGTIGT! / IMPORTANT! MÅL / DIMENSIONS DIVAR VIGTIGT! / IMPORTANT! VIGTIGT læs vores anvisninger før du bruger produktet. Har du problemer med den elektriske installation, skal du kontakte en elektriker. Sørg for at altid slukke for strømmen

Læs mere

TM4 Central Station. User Manual / brugervejledning K2070-EU. Tel Fax

TM4 Central Station. User Manual / brugervejledning K2070-EU. Tel Fax TM4 Central Station User Manual / brugervejledning K2070-EU STT Condigi A/S Niels Bohrs Vej 42, Stilling 8660 Skanderborg Denmark Tel. +45 87 93 50 00 Fax. +45 87 93 50 10 info@sttcondigi.com www.sttcondigi.com

Læs mere

YDEEVNEDEKLARATION. Nr DA

YDEEVNEDEKLARATION. Nr DA YDEEVNEDEKLARATION Nr. 0020 DA 1. Varetypens unikke identifikationskode: fischer sikkerhedsanker FH II-I 2. Tilsigtet anvendelse: Produkt Moment-kontrolleret ekspansionsanker Anvendelsesområde/r Post-installeret

Læs mere

Montageanvisning Assembly instructions. MultiDicer KMD 12, 18

Montageanvisning Assembly instructions. MultiDicer KMD 12, 18 Montageanvisning instructions MultiDicer KMD 12, 18 2 DK Kongskilde MultiDicer KMD 12 og KMD 18 samles som vist på efterfølgende tegninger. 1. Tegning 121117963 Kongskilde MultiDicer leveres fra fabrikken

Læs mere

Parts catalogue BUSH CUTTER

Parts catalogue BUSH CUTTER OREC ISSUED NO. 61-2 Parts catalogue BU CUTTER (EXPORT MODEL) 61, 71 61H, 71H MODEL 61 71 CODE 0257-0258- CONTENTS Fig.1 HANDLE------------------------------------------------------------- 1 Fig.2 FRAME---------------------------------------------------------------

Læs mere

Instruction Manual (GB)... 2 Betjeningsvejledning (DK)... 4

Instruction Manual (GB)... 2 Betjeningsvejledning (DK)... 4 Instruction Manual (GB)... 2 Betjeningsvejledning (DK)... 4 1 Instruction Manual (GB) Operating manual & service instructions for wheel dolly type WD800 - Capacity 800kg. Important: Read and understand

Læs mere

User Manual for LTC IGNOU

User Manual for LTC IGNOU User Manual for LTC IGNOU 1 LTC (Leave Travel Concession) Navigation: Portal Launch HCM Application Self Service LTC Self Service 1. LTC Advance/Intimation Navigation: Launch HCM Application Self Service

Læs mere

BC-10592-2EF-C-NL. RapidBike 3P 1 94-2000-142-21/01 HN 3106 PART LIST PART LIST - DEL LISTE. 1x 4x. O50mm. > 65mm. M6x45mm

BC-10592-2EF-C-NL. RapidBike 3P 1 94-2000-142-21/01 HN 3106 PART LIST PART LIST - DEL LISTE. 1x 4x. O50mm. > 65mm. M6x45mm BC-10592-2EF-C-NL RapidBike 3P O50mm > 65mm 2 HN 3106 PART LIST - DEL LISTE PART LIST 4x M6x45mm 8x 4x 6x 2x 4x 2x 4x 2x 2x 3x 1 94-2000-142-21/01 ASSEMBLY - SAMLEVEJLEDNING M6x45mm x4 6.56mm x8 M6x0mm

Læs mere

Installation Venligst bemærk, håndpumpen kun må monteres i lodret position.

Installation Venligst bemærk, håndpumpen kun må monteres i lodret position. HP-1. HP-3. HP-. Hand Operated Pump Håndpumpe The HP pump is a single acting hand operated pump made of stainless steel St.1.431 making it particularly applicable within the food industry and in environmentally

Læs mere

Mandara. PebbleCreek. Tradition Series. 1,884 sq. ft robson.com. Exterior Design A. Exterior Design B.

Mandara. PebbleCreek. Tradition Series. 1,884 sq. ft robson.com. Exterior Design A. Exterior Design B. Mandara 1,884 sq. ft. Tradition Series Exterior Design A Exterior Design B Exterior Design C Exterior Design D 623.935.6700 robson.com Tradition OPTIONS Series Exterior Design A w/opt. Golf Cart Garage

Læs mere

Skidding System. Challenge Us

Skidding System. Challenge Us Skidding System n Malm Orstads cutting edge Engineering department designs and fabricates tailor made skidding systems for all kinds of enviroments. Our skidding systems are amongst the most efficient

Læs mere

Advarsel: Læs alle instrukser og færdiggør samlingen før brug. Det kan være en fordel at være to til at samle trampolinen.

Advarsel: Læs alle instrukser og færdiggør samlingen før brug. Det kan være en fordel at være to til at samle trampolinen. InGround trampolin Advarsel: - Indeholder små dele som kan forårsage kvælning. - Trampolinen må ikke bruges af børn under 3 år. - For at undgå at glide, bør trampolinen ikke bruges når den er våd. - Kun

Læs mere

JM-3080 PARTS LIST. Jet-Set JM-3080

JM-3080 PARTS LIST. Jet-Set JM-3080 JM-3080 PARTS LIST ITEM DESCRIPTION PART # QTY ITEM DESCRIPTION PART # QTY DECAL - JM-3080 FRONT 1 PANEL N/A 1 46 BALL VALVE JM22-0494 1 (SEE JM71-0004) 47 HANDLE GRIP JM7-0227 1 2 BOLT JM27-0066 10 48

Læs mere

Vores mange brugere på musskema.dk er rigtig gode til at komme med kvalificerede ønsker og behov.

Vores mange brugere på musskema.dk er rigtig gode til at komme med kvalificerede ønsker og behov. På dansk/in Danish: Aarhus d. 10. januar 2013/ the 10 th of January 2013 Kære alle Chefer i MUS-regi! Vores mange brugere på musskema.dk er rigtig gode til at komme med kvalificerede ønsker og behov. Og

Læs mere

Intrinsically Safe Tablet PC

Intrinsically Safe Tablet PC Intrinsically Safe Tablet PC Pad-Ex 01 HR DZ2 User s Manual Zone 2 / DIV 2 EN-1 1 We CAUTION FOR ADAPTER BATTERY SAFETY Relevant information for Ex-protection

Læs mere

Installation Venligst bemærk, håndpumpen kun må monteres i lodret position.

Installation Venligst bemærk, håndpumpen kun må monteres i lodret position. HP-1. HP-3. HP-. Hand Operated Håndpumpe The HP pump is a single acting hand operated pump made of stainless steel St.1.431 making it particularly applicable within the food industry and in environmentally

Læs mere

Parts & Maintenance Manual Reservedels- og vedligeholdelsesmanual

Parts & Maintenance Manual Reservedels- og vedligeholdelsesmanual 4229041-DK-Rev A Parts & Maintenance Manual Reservedels- og vedligeholdelsesmanual Lightweight Fairway Mower with ROPS Letvægts-fairwayplæneklipper med ROPS 67978 LF 550, Kubota V1505-E3B, 5 Gang 2WD 67979

Læs mere

Info og krav til grupper med motorkøjetøjer

Info og krav til grupper med motorkøjetøjer Info og krav til grupper med motorkøjetøjer (English version, see page 4) GENERELT - FOR ALLE TYPER KØRETØJER ØJER GODT MILJØ FOR ALLE Vi ønsker at paraden er en god oplevelse for alle deltagere og tilskuere,

Læs mere

South Baileygate Retail Park Pontefract

South Baileygate Retail Park Pontefract Key Details : available June 2016 has a primary shopping catchment of 77,000 (source: PMA), extending to 186,000 within 10km (source: FOCUS) 86,000 sq ft of retail including Aldi, B&M, Poundstretcher,

Læs mere

Dokumentation af produktionsudstyr til fødevarer

Dokumentation af produktionsudstyr til fødevarer Dokumentation af produktionsudstyr til fødevarer Fødevarekontaktmaterialer (og maskinsikkerhed) IDA 21. marts 2017 Chefkonsulent Jens Sinding Dokumentation i forhold til hvad? Relevante materialer med

Læs mere

XXL-Rehab Gulv forhøjer XXL-Rehab Floor raiser

XXL-Rehab Gulv forhøjer XXL-Rehab Floor raiser BRUGSANVISNING USER MANUAL Gulv forhøjer Floor raiser MAX 200 KG Kan med fordel anvendes til: - Bariatriske brugere. Ideal use for: - Bariatric users. BRUGSANVISNING BRUGSANVISNING BRUGSANVISNING BRUGSANVISNING

Læs mere

2007/1. Texas Garden 32 EL. Betjeningsvejledning User manual

2007/1. Texas Garden 32 EL. Betjeningsvejledning User manual 2007/1 DK GB Betjeningsvejledning User manual Texas Garden 32 EL Texas A/S - Knullen 2 - DK-5260 Odense S - Denmark Tel. +45 6395 5555 - www.texas.dk - post@texas.dk Indholdsfortegnelse Sikkerhedsforskrifter...3

Læs mere

30.48 CM 12 IN MIN CM 24 IN MAX. WARNING: CM Hose is a trip 32 IN hazard

30.48 CM 12 IN MIN CM 24 IN MAX. WARNING: CM Hose is a trip 32 IN hazard 30.48 CM 12 IN MIN 60.96 CM 24 IN MAX WARNING: 81.28 CM Hose is a trip 32 IN hazard 1 A x2 2 1 2 A x2 2 3 3 B 4 x2 C x2 4 5 5 6 6 7 Keesung Manufacturing Co., Ltd ADD: No. 88 Yu Wo Tou Rd., Dong Chong,

Læs mere

Elektriske apparater til husholdningsbrug o.l. Sikkerhed Del 1: Generelle krav

Elektriske apparater til husholdningsbrug o.l. Sikkerhed Del 1: Generelle krav Dansk standard Tillæg DS/IEC 60335-1/A1:2013 + Corr 1:2014 1. udgave 2014-05-08 Elektriske apparater til husholdningsbrug o.l. Sikkerhed Del 1: Generelle krav Household and similar electrical appliances

Læs mere

Safety and Operation Manual Sikkerheds og Instruktionsbog. G-Plex III. 24562G-DK (rev.0)

Safety and Operation Manual Sikkerheds og Instruktionsbog. G-Plex III. 24562G-DK (rev.0) 24562G-DK (rev.0) Safety and Operation Manual Sikkerheds og Instruktionsbog G-Plex III Series: DP - Engine type: Kubota D722 Product code: USAD001 Series: DN - Engine type: Briggs & Stratton 350447 Product

Læs mere

TELT. Oversigt over dele. Følg opstillingsanvisningerne for at opnå det bedste resultat.

TELT. Oversigt over dele. Følg opstillingsanvisningerne for at opnå det bedste resultat. TELT Følg opstillingsanvisningerne for at opnå det bedste resultat. Opstillingstid: ca. 25 min. Krævet antal personer til opstilling: 2 Oversigt over dele Kabine Pløkker (18 stk.) Yderdug Bæretaske Ekstra

Læs mere

YDEEVNEDEKLARATION. Nr DA

YDEEVNEDEKLARATION. Nr DA YDEEVNEDEKLARATION Nr. 0078 DA 1. Varetypens unikke identifikationskode: fischer Betonskrue ULTRACUT FBS II 2. Tilsigtet anvendelse: Produkt Metalanker til brug i beton (svær befæstigelse) Anvendelsesområde/r

Læs mere

YDEEVNEDEKLARATION. Nr DA

YDEEVNEDEKLARATION. Nr DA YDEEVNEDEKLARATION Nr. 0081 DA 1. Varetypens unikke identifikationskode: fischer boltanker FAZ II 2. Tilsigtet anvendelse: Produkt Moment-kontrolleret ekspansionsanker Anvendelsesområde/r Post-installeret

Læs mere

HR7775, HR7774. 4203.000.5832.4.indd 1 15-09-09 15:28

HR7775, HR7774. 4203.000.5832.4.indd 1 15-09-09 15:28 HR7775, HR7774 4203.000.5832.4.indd 1 15-09-09 15:28 EN DA DE EL ES FI FR IT NL NO PT SV TR English Dansk Deutsch Ελληνικα Español Suomi Français Italiano Nederlands Norsk Português Svenska Türkçe AR FA

Læs mere

Mandara. PebbleCreek. Tradition Series. 1,884 sq. ft robson.com. Exterior Design A. Exterior Design B.

Mandara. PebbleCreek. Tradition Series. 1,884 sq. ft robson.com. Exterior Design A. Exterior Design B. Mandara 1,884 sq. ft. Tradition Series Exterior Design A Exterior Design B Exterior Design C Exterior Design D 623.935.6700 robson.com Tradition Series Exterior Design A w/opt. Golf Cart Garage Exterior

Læs mere

Parts & Maintenance Manual Reservedels- og vedligeholdelsesmanual

Parts & Maintenance Manual Reservedels- og vedligeholdelsesmanual 17983-DK-Rev B Parts & Maintenance Manual Reservedels- og vedligeholdelsesmanual AR-522 68098 AR-522, Kubota V203-MT, WD, with ROPS 68098 AR-522, Kubota V203-MT, WD, med ROPS WARNING If incorrectly used,

Læs mere

R9H R9H R9H R9H R9H R9H R9H13303

R9H R9H R9H R9H R9H R9H R9H13303 Resi9 en da R9H84 - R9H84 - R9H84 - R9H844 - R9H0 - R9H0 - R9H0 IP0 NVE5695 http://tv.schneider-electric.com This service guide must be kept for future use. PLEASE NOTE bbthis equipment should be installed,

Læs mere

Fuego. Biopejs / Bio firelight / Bio Feuerstelle. Instruktion / Instructions / Instruktionen

Fuego. Biopejs / Bio firelight / Bio Feuerstelle. Instruktion / Instructions / Instruktionen Fuego Biopejs / Bio firelight / Bio Feuerstelle Instruktion / Instructions / Instruktionen Må kun fyldes hertil / Fill up to here only / Nur hier befüllen DK DK Læs hele instruktionen igennem inden brug

Læs mere

PILLE PRESSE. developed properly for pellet production and all technologies and mechanical solutions are chosen to

PILLE PRESSE. developed properly for pellet production and all technologies and mechanical solutions are chosen to PILLE PRESSE N-ECO pellet mill machine is projected and manufactured in accordance with CE norm about construction s prescriptions and safety. With N-ECO you will save money and get lower pellet production

Læs mere

TC-50 / TC-65 / TC-80. TC-65 20m (65 7 ) 1.05m (42 ) 36.4kW (49hp) 10m( o

TC-50 / TC-65 / TC-80. TC-65 20m (65 7 ) 1.05m (42 ) 36.4kW (49hp) 10m( o R TC-50 / TC-65 / TC-80 TRACKED SPECIFICATION: Conveyor Length: Belt Width: Net Engine (Tier 3)Power: Max Discharge height: TC-50 15.7m (51 7 ) 1.05m (42 ) 36.4kW (49hp) 7.6m(24 11 ) @ 27 o TC-65 20m (65

Læs mere

DANSK. INSTALLATIONSVEJLEDNING DS Pro Lærred med motor ADVARSEL!

DANSK. INSTALLATIONSVEJLEDNING DS Pro Lærred med motor ADVARSEL! DANSK INSTALLATIONSVEJLEDNING DS Pro Lærred med motor Udpakningsinstruktioner Åben indpakningen forsigtigt og læg indholdet på et stykke pap eller en anden beskyttende overflade for at undgå beskadigelse.

Læs mere

YDEEVNEDEKLARATION. DoP: 0084 til fischer Highbond-Anchor FHB II Inject (Limanker til anvendelse i beton) DA

YDEEVNEDEKLARATION. DoP: 0084 til fischer Highbond-Anchor FHB II Inject (Limanker til anvendelse i beton) DA YDEEVNEDEKLARATION DoP: 0084 til fischer Highbond-Anchor FHB II Inject (Limanker til anvendelse i beton) DA 1. Varetypens unikke identifikationskode: DoP: 0084 2. Tilsigtet anvendelse: Post-installeret

Læs mere

Topdresser 1800 for Workman 3000/4000 Series

Topdresser 1800 for Workman 3000/4000 Series Form No. Topdresser 1800 for Workman 3000/4000 Series Model No. 44225 90001 and Up Parts Catalog Ordering Replacement Parts To order replacement parts, please supply: the part number, the quantity, and

Læs mere

DK Manual GB User Manual MPC Texas A/S - Knullen 22 - DK-5260 Odense S - Denmark Version 12.1 Tel

DK Manual GB User Manual MPC Texas A/S - Knullen 22 - DK-5260 Odense S - Denmark Version 12.1 Tel DK Manual GB User Manual MPC 1300 Texas A/S - Knullen 22 - DK-5260 Odense S - Denmark Version 12.1 Tel. +45 6395 5555 - - post@texas.dk ID1: Identifikation af dele ID2: Identification of parts 2 Symboler

Læs mere

Product. Information. A. u. K. Müller. 2/2-way Drain Valve NC, DN 40. Series Characteristics. Possible approvals

Product. Information. A. u. K. Müller. 2/2-way Drain Valve NC, DN 40. Series Characteristics. Possible approvals Solenoid valves Control valves Special valves and systems GmbH & Co. KG Dresdener Str. 162 D-40595 Düsseldorf/Germany Tel.: +49(0)1-73-0 Fax: +49(0)1-73-281 e-mail: info@akmueller.de Internet: www.akmueller.de

Læs mere

YDEEVNEDEKLARATION. Nr DA. appendiks B 1 - B 4

YDEEVNEDEKLARATION. Nr DA. appendiks B 1 - B 4 YDEEVNEDEKLARATION Nr. 0069 DA 1. Varetypens unikke identifikationskode: fischer slaganker EA II 2. Tilsigtet anvendelse: Produkt Metalanker til brug i beton (svær befæstigelse) Anvendelsesområde/r Post-installeret

Læs mere

MS-H280-Pro Magnetic Stirrer

MS-H280-Pro Magnetic Stirrer MS-H280-Pro Magnetic Stirrer www..com Copyright: No part of this manual may be reproduced or transmitted without prior written permission of. VERSION201407 CONTENTS Chapter 1: Working Principle... 3 1

Læs mere

KNIFE GATE VALVE FAF 6500

KNIFE GATE VALVE FAF 6500 PRODUCTION STANDARTS DN50 DN600 PN 10 Connection EN 1092-2 / ISO 7005-2 Face to Face EN 558 Series Marking EN 19 Tests EN 12266-1 Corrosion Protection Electrostatic Powder Epoxy Features y Uni-directional

Læs mere

Portal Registration. Check Junk Mail for activation . 1 Click the hyperlink to take you back to the portal to confirm your registration

Portal Registration. Check Junk Mail for activation  . 1 Click the hyperlink to take you back to the portal to confirm your registration Portal Registration Step 1 Provide the necessary information to create your user. Note: First Name, Last Name and Email have to match exactly to your profile in the Membership system. Step 2 Click on the

Læs mere

KALK- OG TEGLVÆRKSFORENINGEN. CPR Sustainable Construction

KALK- OG TEGLVÆRKSFORENINGEN. CPR Sustainable Construction CPR Sustainable Construction 1 Tommy Bisgaard - Direktør i Kalk- og Teglværksforeningen - Formand for DS 417 (CEN TC350 & 351) - Formand for miljøkomiteen i TBE & CU (keramiske industrier i Europa) - Medlem

Læs mere

DEUTSCH. Electric

DEUTSCH. Electric DEUTSCH D Electric 8-00-0 S SVENSKA 5 8 6 9 5 5.. SVENSKA S = 0 mm = 0 mm = 0 mm = 50 mm 0 mm 60 mm A C B.. 5.. 6. S SVENSKA 8. 9. INFORMATION OM STRØMFORBRUG Flere og flere maskiner, som f.eks. plæneklippere,

Læs mere

No Part no. Description Q ty Remarks No Part no. Description Q ty Remarks Filter, air cleaner Air cleaner 1 Assy 2 050

No Part no. Description Q ty Remarks No Part no. Description Q ty Remarks Filter, air cleaner Air cleaner 1 Assy 2 050 1 2 2 3 No Part no. Description Q ty Remarks No Part no. Description Q ty Remarks 1 050604-1 Filter, air cleaner 1 3 050601-1 Air cleaner 1 Assy 2 050603-1 Tube, inlet 1 No. Part No. Description Q ty Remarks

Læs mere

WIO200A Water in oil sensor

WIO200A Water in oil sensor WIO200A Water in oil sensor Datasheet 111688-900 Rev. 1.03 Dato: 2012-06-01 03-01-0501-CRJ-04 Side 1 af 13 Technical Sensor Data Order Order number A01-110-0101-01 Output Analogue output 4 20 ma (galvanic

Læs mere

Lithium-Ion Jump-Starters / Jumper Cables

Lithium-Ion Jump-Starters / Jumper Cables AUTOMOTIVE Lithium-Ion Jump-Starters / Jumper Cables Lithium-Ion Jump-Starter 1300: Part No. DRLJS130 1300 4 6 8 cylinder (6 liter gas 3 liter diesel) SafeJump technology prevents sparking and protects

Læs mere

IBM Network Station Manager. esuite 1.5 / NSM Integration. IBM Network Computer Division. tdc - 02/08/99 lotusnsm.prz Page 1

IBM Network Station Manager. esuite 1.5 / NSM Integration. IBM Network Computer Division. tdc - 02/08/99 lotusnsm.prz Page 1 IBM Network Station Manager esuite 1.5 / NSM Integration IBM Network Computer Division tdc - 02/08/99 lotusnsm.prz Page 1 New esuite Settings in NSM The Lotus esuite Workplace administration option is

Læs mere

Privat-, statslig- eller regional institution m.v. Andet Added Bekaempelsesudfoerende: string No Label: Bekæmpelsesudførende

Privat-, statslig- eller regional institution m.v. Andet Added Bekaempelsesudfoerende: string No Label: Bekæmpelsesudførende Changes for Rottedatabasen Web Service The coming version of Rottedatabasen Web Service will have several changes some of them breaking for the exposed methods. These changes and the business logic behind

Læs mere

YDEEVNEDEKLARATION. Nr DA

YDEEVNEDEKLARATION. Nr DA YDEEVNEDEKLARATION Nr. 0019 DA 1. Varetypens unikke identifikationskode: fischer High-Bond anker FHB II 2. Tilsigtet anvendelse: Produkt Limanker til anvendelse i beton Anvendelsesområde/r Post-installeret

Læs mere

YDEEVNEDEKLARATION. Nr DA

YDEEVNEDEKLARATION. Nr DA YDEEVNEDEKLARATION Nr. 0072 DA 1. Varetypens unikke identifikationskode: Injektionssystem FIS V 2. Tilsigtet anvendelse: Produkt Limanker til brug i beton Anvendelsesområde/r Til fastgørelse og understøttelse

Læs mere

Betjeningsvejledning User manual LME Tel

Betjeningsvejledning User manual LME Tel DK GB Betjeningsvejledning User manual LME 1100 Indholdsfortegnelse Texas A/S - Knullen 22 - DK-5260 - Original Odense brugsanvisning S - Denmark Version 15.1 Tel. +45 6395 5555 - www.texas.dk - post@texas.dk

Læs mere

No. Part No. Description Q ty Remarks Cleaner Assembly (Includes Fig.1,2,4 & 5) Cap Tube, inlet Filter, air cleane

No. Part No. Description Q ty Remarks Cleaner Assembly (Includes Fig.1,2,4 & 5) Cap Tube, inlet Filter, air cleane No. Part No. Description Q ty Remarks 1 050601 Cleaner Assembly (Includes Fig.1,2,4 & 5) 2 050602 Cap 3 050603 Tube, inlet 4 050604 Filter, air cleaner 5 050605 Net, air cleaner No. Part No. Description

Læs mere

YDEEVNEDEKLARATION. Nr DA

YDEEVNEDEKLARATION. Nr DA YDEEVNEDEKLARATION Nr. 0017 DA 1. Varetypens unikke identifikationskode: fischer betonskrue FBS, FBS A4 og FBS C 2. Tilsigtet anvendelse: Produkt Metalanker til brug i beton (svær befæstigelse) Anvendelsesområde/r

Læs mere

YDEEVNEDEKLARATION. Nr DA

YDEEVNEDEKLARATION. Nr DA YDEEVNEDEKLARATION Nr. 0088 DA 1. Varetypens unikke identifikationskode: fischer Injektionssystem FIS EM 2. Tilsigtet anvendelse: Produkt Limanker til anvendelse i beton Anvendelsesområde/r Post-installeret

Læs mere

O-DINS-1 (Open DIN spindle set for IKA Rotavisc)

O-DINS-1 (Open DIN spindle set for IKA Rotavisc) O-DINS-1 (Open DIN spindle set for IKA Rotavisc) ENGLISH !!!!!! Fig. 1 Explication of warning symbols... 5! Safety instructions... 6 Intended use... 6 Unpacking... 6 Assembly... 8 Spindle information...

Læs mere