Dansk Standard DS/EN 1871 1. udgave Godkendt:2000-03-21 Vejudstyr. Afmærkningsmaterialer. Fysiske egenskaber Road marking materials - Physical properties DANSK STANDARD - Eftertryk uden tilladelse forbudt Kollegievej 6 DK-2920 Charlottenlund Tel (+45) 39 96 61 01 Fax (+45) 39 96 61 02 E-mail: DANSK.STANDARD@ds.dk www.ds.dk
DS/EN 1871 København DS Projekt: 19747 ICS: 93.080.20 Deskriptorer: slitage,alkalimodstand,kørebane,farve,konstruktion,definitioner,varmemodstand,horisontal,luminans,mærkningsmaterialer,mærk ning,fysiske egenskaber,reflektion,vejafmærkning,vejsikkerhed,prøvning,vejkontrol,transportsikkerhed, specifikationer,signalering,sikkerhed Første del af denne publikations betegnelse er: DS/EN, hvilket betyder, at det er en europæisk standard, der har status som dansk standard. Denne publikations overensstemmelse er: IDT med: EN 1871:2000 på engelsk DS-publikationstyper DANSK STANDARD udgiver forskellige publikationstyper. Typen på denne publikation fremgår af forsiden. Der kan være tale om: Dansk standard = standard, der er udarbejdet på nationalt niveau, eller som er baseret på et andet lands nationale standard eller = standard, der er udarbejdet på internationalt og/eller europæisk niveau, og som har fået status som dansk standard DS-information = publikation, der er udarbejdet på nationalt niveau, og som ikke har opnået status som standard, eller = publikation, der er udarbejdet på internationalt og/eller europæisk niveau, og som ikke har fået status som standard, fx en teknisk rapport, eller = europæisk præstandard DS-håndbog = samling af standarder, eventuelt suppleret med informativt materiale DS-hæfte = publikation med informativt materiale Til disse publikationstyper kan endvidere udgives = tillæg og rettelsesblade DS-publikationsform Publikationstyperne udgives i forskellig form som henholdsvis = fuldtekstpublikation (publikationen er trykt i sin helhed) = godkendelsesblad (publikationen leveres i kopi med et trykt DS-omslag) = elektronisk (publikationen leveres på et elektronisk medie) DS-betegnelse Alle DS-publikationers betegnelse begynder med DS efterfulgt af et eller flere præfikser og et nr. fx DS 383, DS/EN 5414 osv. Hvis der efter nr. er angivet at A eller Cor, betyder det, enten at det er et tillæg eller et rettelsesblad til hovedstandarden, eller at det er indført i hovedstandarden. DS-betegnelse angives på forsiden. Overensstemmelse med anden publikation: Overensstemmelse kan enten være IDT, EQV, NEQ eller MOD = IDT: Når publikationen er identisk med en given publikation. = EQV: Når publikationen teknisk er i overensstemmelse med en given publikation, men præsentationen er ændret. = NEQ: Når publikationen teknisk eller præsentationsmæssigt ikke er i overensstemmelse med en given standard, men udarbejdet på baggrund af denne. = MOD: Når publikationen er modificeret i forhold til en given publikation.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 1871 January 2000 ICS 93.080.20 English version Road marking materials - Physical properties Produits de marquage routier - Propriétés physiques This European Standard was approved by CEN on 12 November 1999. Straßenmarkierungsmaterialien - Physikalische Eigenschaften CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1871:2000 E
Page 2 EN 1871:2000 Contents Page Introduction... 4 1 Scope... 4 2 Normative references... 4 3 Definitions... 5 4 Requirements... 5 Annex A (normative)... 12 Paint and cold plastics Test method for determining the chromaticity co-ordinates and luminance factor... 12 Annex B (normative)... 13 Paint and cold plastics Test method for determining the storage stability... 13 Annex C (normative)... 17 Paint Test method for determining the bleed resistance... 17 Annex D (normative)... 18 Paint, cold plastics and thermoplastics - Test method for determining the alkali resistance of the materials... 18 Annex E (normative)... 22 Thermoplastics Test method for determining the chromaticity co-ordinates and luminance factor... 22 Annex F (normative)... 23 Thermoplastics Test method for determining the softening point... 23 Annex G (normative)... 26 Thermoplastics Test method for determining the heat stability... 26 Annex H (normative)... 31 Thermoplastics Test method for determining the cold impact resistance... 31 Annex J (normative)... 33 Thermoplastics Test method for determining the indentation value... 33 Annex K (normative)... 37 Thermoplastics and cold plastics Test method for determining the Tröger wear... 37 Bibliography... 42
Page 3 EN 1871:2000 Foreword This European Standard has been prepared by Technical Committee CEN/TC 226 "Road equipment", the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2000, and conflicting national standards shall be withdrawn at the latest by July 2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. The annexes A, B, C, D, E, F, G, H, J and K of this European Standard are normative.
Page 4 EN 1871:2000 Introduction This European Standard gives the physical properties of road marking materials used in horizontal signalization. It includes annexes for test methods. Identification requirements are covered in pren 12802:1999. 1 Scope This European Standard specifies the laboratory requirements and test methods for retroreflective and other road marking materials, both permanent and temporary. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 1436:1997 pren 12802:1999 Road marking materials Road marking performance for road users Road marking materials Laboratory methods for identification ISO 787-11:1981 General methods of test for pigments and extenders Part 11: Determination of tamped volume and apparent density after tamping ISO 1514:1993 ISO 2814 ISO 4892 ISO 7724-2 Paints and varnishes - Standard panels for testing Paints and varnishes Comparison of contrast ratio (hiding power) of paints of the same type and colour Plastics Methods of exposure to laboratory light sources Part 1: General guidance Part 2: Xenon-arc sources Part 3: Fluorescent UV lamps Paints and varnishes Colorimetry Part 2 : Colour measurement