Dansk Standard DS/EN 1848-2 1. udgave Godkendt:2001-06-01 Fleksible membraner til fugtisolering Bestemmelse af længde, bredde og rethed Del 2: Plast- og gummifolier til tagdækning Flexible sheets for waterproofing Determination of length, width, straightness and flatness Part 2: Plastic and rubber sheets for roof waterproofing DANSK STANDARD - Eftertryk uden tilladelse forbudt Kollegievej 6 DK-2920 Charlottenlund Tel (+45) 39 96 61 01 Fax (+45) 39 96 61 02 E-mail: DANSK.STANDARD@ds.dk www.ds.dk
DS/EN 1848-2 København DS Projekt: 13137 ICS: 91.100.50 Deskriptorer: definitioner,længde,prøvning,rethed,underlag,gummi,tagunderlag,gummifolier,tagdækning Første del af denne publikations betegnelse er: DS/EN, hvilket betyder, at det er en europæisk standard, der har status som dansk standard. Denne publikations overensstemmelse er: IDT med: EN 1848-2:2001 på engelsk DS-publikationstyper DANSK STANDARD udgiver forskellige publikationstyper. Typen på denne publikation fremgår af forsiden. Der kan være tale om: Dansk standard standard, der er udarbejdet på nationalt niveau, eller som er baseret på et andet lands nationale standard eller standard, der er udarbejdet på internationalt og/eller europæisk niveau, og som har fået status som dansk standard DS-information publikation, der er udarbejdet på nationalt niveau, og som ikke har opnået status som standard, eller publikation, der er udarbejdet på internationalt og/eller europæisk niveau, og som ikke har fået status som standard, fx en teknisk rapport, eller europæisk præstandard DS-håndbog samling af standarder, eventuelt suppleret med informativt materiale DS-hæfte publikation med informativt materiale Til disse publikationstyper kan endvidere udgives tillæg og rettelsesblade DS-publikationsform Publikationstyperne udgives i forskellig form som henholdsvis fuldtekstpublikation (publikationen er trykt i sin helhed) godkendelsesblad (publikationen leveres i kopi med et trykt DS-omslag) elektronisk (publikationen leveres på et elektronisk medie) DS-betegnelse Alle DS-publikationers betegnelse begynder med DS efterfulgt af et eller flere præfikser og et nr. fx DS 383, DS/EN 5414 osv. Hvis der efter nr. er angivet at A eller Cor, betyder det, enten at det er et tillæg eller et rettelsesblad til hovedstandarden, eller at det er indført i hovedstandarden. DS-betegnelse angives på forsiden. Overensstemmelse med anden publikation: Overensstemmelse kan enten være IDT, EQV, NEQ eller MOD IDT: Når publikationen er identisk med en given publikation. EQV: Når publikationen teknisk er i overensstemmelse med en given publikation, men præsentationen er ændret. NEQ: Når publikationen teknisk eller præsentationsmæssigt ikke er i overensstemmelse med en given standard, men udarbejdet på baggrund af denne. MOD: Når publikationen er modificeret i forhold til en given publikation.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 1848-2 May 2001 ICS 91.100.50 English version Flexible sheets for waterproofing - Determination of length, width, straightness and flatness - Part 2: Plastic and rubber sheets for roof waterproofing Feuilles souples d'étanchéité - Détermination de la longueur, de la largeur, de la rectitude et de la planéité - Partie 2: Feuilles d'étanchéité de toiture plastiques et élastomères This European Standard was approved by CEN on 2 June 2000. Abdichtungsbahnen - Bestimmung der Länge, Breite, Geradheit und Planlage - Teil 2: Kunststoff- und Elastomerbahnen für Dachabdichtungen CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1848-2:2001 E
Page 2 EN 1848-2:2001 Contents Page Foreword... 3 Introduction... 3 1 Scope... 3 2 Normative references... 3 3 Definitions... 3 4 Sampling... 4 5 Determination of length... 4 6 Determination of width... 4 7 Determination of straightness and flatness...5 8 Precision of the test methods... 5 9 Test report... 6
Page 3 EN 1848-2:2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 254 " Flexible sheets for waterproofing", the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2001, and conflicting national standards shall be withdrawn at the latest by July 2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Introduction This European Standard is intended for characterisation of plastic and rubber sheets as manufactured or supplied before use. This test method relates exclusively to products or to their components where appropriate, and not to waterproofing membrane systems composed of such products and installed in the works. This test is intended to be used in conjunction with European Standard "Definition and Characteristics" for plastic and rubber sheets for roof waterproofing. 1 Scope This European Standard specifies methods for the determination of length, width, straightness and flatness of plastic and rubber sheets for roof waterproofing supplied in rolls. 2 Normative references This European Standard incorporates, by dated or undated references, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest editions of the publication referred to apply (including amendments). EN 13416 3 Terms and definitions Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Rules for sampling. For the purposes of this European Standard, the following terms and definitions apply: 3.1 Length dimension of the roll measured in the manufacturing direction.