RE22R2MYMR ( ) Multi-function Timing Relay s 300h V AC/DC - 2C/O

Transkript

1 Produkt datablad Karakteristika RE22R2MYMR ( ) Multi-function Timing Relay s 300h V AC/DC - 2C/O Primær Produktsortiment Produkttype Digital udgangstype Enhedens korte navn Nominel udgangsstrøm Zelio Time Modular timing relay Relæ RE22 8 A Alternativ Kontaktype og sammensætning Tidsforsinkelsestype Time delay range Betjening [Us] forsyningsspænding Indgangsspænding Spændingsområde 1 C/O timed or instantaneous contact, cadmium free 2 C/O timed contact, cadmium free A At AW C D Di H Ht Qg Qt W Ct Dw Hw Wt Dt Dit Diw Qgt Qtt Qgw Qtw s s s s h min s h min s Drejegreb Diagnostic button External potentiometer V AC/DC ved 50/60 Hz <= 2.4 V Us Tilslutningsfrekvens Hz (+/- 5 %) Tilslutningsklemmer Skrueterminaler : 1 x x 3.3 mm², AWG 20...AWG 12 solid kabel uden kabel ende Skrueterminaler : 2 x x 2.5 mm², AWG 20...AWG 14 solid kabel uden kabel ende Skrueterminaler : 1 x x 2.5 mm², AWG 24...AWG 14 fleksibel kabel med kabel ende Oplysningerne i denne dokumentation indeholder generelle beskrivelser og/eller tekniske egenskaber af udførelsen af produkerne indeholdt heri. Denne dokumentation er ikke tænkt som en erstatning for, og skal ikke anvendes til bestemmelse af egnethed eller pålidelighed af disse produkter til specifikke brugerapplikationer. Det er brugers eller integrators pligt at foretage den nødvendige og fuldstændige risikoanalyse, evaluering og afprøvning af produkter med hensyn til den relevante specifikke anvendelse eller brug heraf. Hverken Schneider Electric Industries SAS, nogle af dets associerede selskaber eller datterselskaber er ansvarlig eller erstatningspligtig for misbrug af oplysningerne heri. 1 / 12

2 Tilspændingsmoment N.m i henhold til IEC Kapslingsmateriale Skrueterminaler : 2 x x 1.5 mm², AWG 24...AWG 16 fleksibel kabel med kabel ende Self-extinguishing Gentagelsesnøjagtighed +/- 0.5 % i henhold til IEC Temperaturafvigelse Spændingsafvigelse +/ %/ C +/- 0.2 %/V Indstillingsnøjagtighed for tidsforsinkelse +/- 10 % of full scale ved 25 C i henhold til IEC Minimum impulsvarighed 30 ms 100 ms (with load in parallel) Isolationsmodstand 100 MOhm ved 500 V DC i henhold til IEC Resettid Imunitet over for microafbrydelser Effektforbrug i VA Effektforbrug i W Koblingsevne i VA Minimum sluttestrøm Maximum sluttestrøm Masimal spænding Elektrisk holdbarhed Mekanisk holdbarhed 120 ms (på de-energinisering) <= 10 ms 3 VA ved 240 V AC 1.5 W ved 240 V DC 2000 VA 10 ma 5 V DC 8 A 250 V AC kredsløb til 8 A ved 250 V AC kredsløb til 2 A ved 24 V DC kredsløb [Uimp] impulsmodstandsspænding 5 kv til µs i henhold til IEC Forsinket svar < 100 ms Creepage distance 4 kv/3 i henhold til IEC Overspændingskategori III i henhold til IEC Sikkerhedsdata Mounting position MTTFd = år B10d = Any position Montagevejledning 35 mm DIN skinne i henhold til EN/IEC Status LED Bredde Vægt Grøn LED backlight (konstant) til dial pointer indication Gul LED (konstant) til output relay energised Gul LED (fast flashing) til timing in progress and output relay de-energised Gul LED (slow flashing) til timing in progress and output relay energised 22.5 mm kg Miljø dielektrisk gennemslagsholdbarhed standarder IEC UL 508 direktiver productcertificeringer 2.5 kv til 1 ma/1 minut ved 50 Hz between relay output and power supply med basic insulation i henhold til IEC /108/EC - elektromagnetisk kompatibilitet 2006/95/EC - lavspændingsdirektiv CCC CE CSA GL UL RCM EAC China RoHS anbefalede temperatur ved drift C optimal temperatur til opbevaring C IP kapslingsklasse IP20 (terminaler) i henhold til IEC IP40 (hus) i henhold til IEC IP50 (front panel) i henhold til IEC forureningsgrad 3 i henhold til IEC vibrationsmodstand 20 m/s² (f = Hz) i henhold til IEC chokmodstand 15 gn (ikke aktiv) (varighed = 11 ms) i henhold til IEC gn (aktiv) (varighed = 11 ms) i henhold til IEC / 12

3 relativ fugtighed 95 % ved C elektromagnetisk kompatibilitet Fast transients immunity test (testniveau: 1 kv, level 3 - capacitive connecting clip) i henhold til IEC Surge immunity test (testniveau: 1 kv, level 3 - differential tilstand) i henhold til IEC Surge immunity test (testniveau: 2 kv, level 3 - fælles mode) i henhold til IEC Electrostatic discharge (testniveau: 6 kv, level 3 - kontaktafledning) i henhold til IEC Electrostatic discharge (testniveau: 8 kv, level 3 - luftafladning) i henhold til IEC Radiated radio-frekvens electromagnetic field immunity test (testniveau: 10 V/m, level 3-80 MHz...1 GHz) i henhold til IEC Conducted RF disturbances (testniveau: 10 V, level MHz) i henhold til IEC Fast transient bursts (testniveau: 2 kv, level 3 - direct contact) i henhold til IEC Immunity to microbreaks and voltage drops (testniveau: 30 % ms) i henhold til IEC Immunity to microbreaks and voltage drops (testniveau: 100 % - 20 ms) i henhold til IEC Bæredygtighed bæredygtighed RoHS (datokode: YYWW) REACH Miljøprofil Produktets levetid Green Premium produkt Compliant - since Schneider Electric declaration of conformity Produktet indholder ikke SVHC over det tilladte Tilgængelig Tilgængelig Dimensions Wiring Diagram Function A: Power On-Delay On energisation of power supply, the timing period T starts. After timing, the output(s) R close(s).the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). 3 / 12

4 Function At: Power On-Delay with Pause / Summation Control On energisation of power supply, the timing period T starts.timing can be interrupted / paused each time X1 energizes.except for RE17*, RE22R2AMU, RE22R2MMW, RE22R2MMU, RE22R2MJU, timing can be interrupted / paused each time Y1 energizes.when the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R close(s).the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). with Pause / Summation Control with Pause / Summation Control with Retrigger / Restart Control with Retrigger / Restart Control Function Aw : Power On-Delay With Retrigger / Restart Control On energisation of power supply, the timing period T starts.at the end of the timing period T, the output(s) R close(s).energization of Y1 makes the output(s) R open(s).deenergization of Y1 restarts timing period T.At the end of timing period T, the output(s) R close(s).the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST") 4 / 12

5 Function C: Off-Delay Relay with Control Signal After energisation of power supply and energization of Y1 causes output(s) R close(s). When Y1 deenergizes, timing T starts.at the end of this timing period T,the output(s) R revert(s) to its/their initial position.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). Function Ct: Off-Delay Relay with Control Signal & With Pause / Summation Control After energisation of power supply and energization of Y1 cause output(s) R close(s).when Y1 deenergizes, timing starts and the timing can be interrupted / paused each time X1 energizes. When the cumulative total of time periods elapsedreaches the pre-set value T, the output(s) R revert(s) to its/their initial state.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). 5 / 12

6 Function D: Symmetrical Flashing Relay (Starting Pulse Off) On energisation of power supply, output(s) R starts at its/their initial state for timing duration T then change(s) to output(s) R close(s) for the same timing duration T.This cycle is repeated indefintely until power supply removal.specially for RE17*, RE22R2AMU, RE22R2MMW, RE22R2MMU, RE22R2MJU,this D function can only be initiated by energizing Y1 permanently.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). with Retrigger / Restart Control Function: 2 Output with Retrigger / Restart Control Function Dt: Symmetrical Flashing Relay (Starting Pulse Off) & With Pause / Summation Control On energisation of power supply, output(s) R starts at its/their initial state for timing duration T and the timing can be interrupted / paused each time X1 energizes.when the cumulative total of time periods elapsed reaches the pre-set value T, then changes to output (s) R close(s).the output(s) R close state will remain for the same timing duration T and the timing can be interrupted / paused each time X1 energizes.when the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R revert(s) to its/their initial state.this cycle is repeated indefintely until power supply removal.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). 6 / 12

7 t'1 + t'2 + t'1 + t'2 + Function DW: Symmetrical Flashing Relay (Starting Pulse Off) & With Retrigger / Restart Control On energisation of power supply, output(s) R starts at its/their initial state for timing duration T then change(s) to output(s) R close(s) for the same timing duration T.This cycle is repeated indefintely until power supply removal.specially for RE17*, RE22R2AMU, RE22R2MMW, RE22R2MMU, RE22R2MJU,this D function can only be initiated by energizing Y1 permanently.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). Function Di: Symmetrical Flashing Relay (Starting Pulse On) On energisation of power supply, output(s) R starts at output(s) R close(s) for timing duration T then revert(s) to its/their initial state for the same timing duration T.This cycle is repeated indefintely until power supply removal.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). Function Dit: Symmetrical Flashing Relay (Starting Pulse On) & With Pause / Summation Control 7 / 12

8 On energisation of power supply, output(s) R starts at output(s) R close(s) for timing duration T and the timing can be interrupted / paused each time X1 energizes.when the cumulative total of time periods elapsed reaches the pre-set value T, then revert(s) to its/their initial state.the output(s) R at initial state will remain for the same timing duration T and the timing can be interrupted / paused each time X1 energizes.when the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R change(s) to close state.this cycle is repeated indefintely until power supply removal.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). t'1 + t'2 + t'1 + t'2 + Function Diw: Symmetrical Flashing Relay (Starting Pulse On) & With Retrigger / Restart Control On energisation of power supply, output(s) R starts at output(s) R close(s) for timing duration T then revert(s) to its/their initial state for the same timing duration T.This cycle is repeated indefintely until power supply removal.at any state of the output(s) R when Y1 energizes, the output(s) R will revert to its/their initial state and followed by Y1 deenergizes then restarts the same operation as described at the beginning.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). Function H: Interval Relay On energisation of power supply, output(s) R close(s) and timing period T starts.at the end of the timing period T, the output(s) R revert (s) to its/their initial state.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). 8 / 12

9 Function Ht: Interval Relay & With Pause / Summation Control On energisation of power supply, output(s) R close(s) and timing period T starts.the timing can be interrupted / paused each time X1 energizes. When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R revert(s) to its/their initial statereenergization of X1 will also cause output(s) R close(s) if the time has elapsed and restart the same operation as described at the beginning.except for RE17*, RE22R2AMU, RE22R2MMW, RE22R2MMU, RE22R2MJU, timing can be interrupted / paused each time Y1 energizes.the second output (R2) can be either timed (when set to "TIMED" or instantaneous (when set to "INST"). with Retrigger / Restart Control Function: 2 Output with Retrigger / Restart Control Function Hw: Interval Relay & with Retrigger / Restart Control On energisation of power supply, output(s) R close(s) and timing period T starts.at the end of the timing period T, the output(s) R revert (s) to its/their initial state.at any state of the output(s) R when Y1 energizes followed by deenergizes, the output(s) R close(s) then restarts the same operation as described at the beginning.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). 9 / 12

10 Function Qg: Star-Delta Relay (2 CO with same Common) On energisation of power supply, the output R3 closes such that energizes STAR CONTACTOR + MAIN CONTACTOR and the timing T starts (STAR connection time duration starts).at the end of the timing period T, the output R3 reverts to its initial state such that deenergizes STAR CONTACTOR and causes t transition time starts.at the end of the transition time, the output R4 closes such that energizes DELTA CONTACTOR. t : 20, 40, 60, 80, 100, 120, 140 ms Function Qgt: Star-Delta Relay (2 CO with same common) with Pause / Summation Control On energisation of power supply, the output R3 closes such that energizes STAR CONTACTOR + MAIN CONTACTOR and the timing T starts (STAR connection time duration starts).during STAR connection time, the timing can be interrupted / paused each time X1 energizes.when the cumulative total of time periods elapsed reaches the pre-set value T, R3 reverts to its initial state such that deenergizes STAR CONTACTOR and causes t transition time starts.at the end of the transition time, the output R4 closes such that energizes DELTA CONTACTOR. NOTE: RE22R2MYMR is with fixed transition time, t: 50ms Function Qt: Star-Delta Relay (2 CO with Split Common) On energisation of power supply, the output R3 & R4 initializes at its initial state such that energizes STAR CONTACTOR + MAIN CONTACTOR and the timing T starts (STAR connection time duration starts).at the end of the timing period T, the output R3 closes such that deenergizes STAR CONTACTOR and causes t transition time starts.at the end of the transition time, the output R4 closes such that energizes DELTA CONTACTOR. t : 20, 40, 60, 80, 100, 120, 140 ms 10 / 12

11 Function Qtt: Star-Delta Relay (2 CO with same common) with Pause / Summation Control On energisation of power supply, the output R3 & R4 initializes at its initial state such that energizes STAR CONTACTOR + MAIN CONTACTOR and the timing T starts (STAR connection time duration starts).during STAR connection time, the timing can be interrupted / paused each time X1 energizes.when the cumulative total of time periods elapsed reaches the pre-set value T, the output R3 closes such that deenergizes STAR CONTACTOR and causes t transition time starts.at the end of the transition time, the output R4 closes such that energizes DELTA CONTACTOR. NOTE: RE22R2MYMR is with fixed transition time, t: 50ms Function W: Interval Relay with Control Signal Off After energisation of power supply and on energization of Y1 following by denergization of Y1, the output(s) R close(s) and starts the timing T.At the end of the timing period, the output(s) R revert(s) to its/their initial state.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). Function Wt: Interval Relay with Control Signal Off & with Pause / Summation Control After energisation of power supply and on energization of Y1 following by denergization of Y1, the output(s) R close(s) and starts the timing T.Timing can be interrupted / paused each time X1 energizes.when the cumulative total of time periods elapsed reaches the preset value T, the output(s) R revert(s) to its/their initial state.the second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST"). 11 / 12

12 Legend Relay de-energised Relay energised Output open Output closed U - Supply R1/R2 2 timed outputs - Ta - Adjustable On-delay Tr - Adjustable Off-delay X1 - Pause / Summation control Y1 - Retrigger / Restart control X2 - Function Selection R2 The second output is instantaneous if the right position is selected inst. - T - Timing period R4 - Delta contact output t - Delay to switch ON Delta contact output R3 - Star-Delta contact output 12 / 12