Indvendig afskærming til vinduer og døre Beskyttelse mod kvælningsfare Krav og prøvningsmetoder for sikkerhedsanordninger

Transkript

1 Dansk standard DS/EN udgave Indvendig afskærming til vinduer og døre Beskyttelse mod kvælningsfare Krav og prøvningsmetoder for sikkerhedsanordninger Internal blinds Protection from strangulation hazards Requirements and test methods for safety devices

2 DS/EN København DS projekt: M ICS: Første del af denne publikations betegnelse er: DS/EN, hvilket betyder, at det er en europæisk standard, der har status som dansk standard. Denne publikations overensstemmelse er: IDT med: EN 16434:2014. DS-publikationen er på engelsk. DS-publikationstyper Dansk Standard udgiver forskellige publikationstyper. Typen på denne publikation fremgår af forsiden. Der kan være tale om: Dansk standard standard, der er udarbejdet på nationalt niveau, eller som er baseret på et andet lands nationale standard, eller standard, der er udarbejdet på internationalt og/eller europæisk niveau, og som har fået status som dansk standard DS-information publikation, der er udarbejdet på nationalt niveau, og som ikke har opnået status som standard, eller publikation, der er udarbejdet på internationalt og/eller europæisk niveau, og som ikke har fået status som standard, fx en teknisk rapport, eller europæisk præstandard DS-håndbog samling af standarder, eventuelt suppleret med informativt materiale DS-hæfte publikation med informativt materiale Til disse publikationstyper kan endvidere udgives tillæg og rettelsesblade DS-publikationsform Publikationstyperne udgives i forskellig form som henholdsvis fuldtekstpublikation (publikationen er trykt i sin helhed) godkendelsesblad (publikationen leveres i kopi med et trykt DS-omslag) elektronisk (publikationen leveres på et elektronisk medie) DS-betegnelse Alle DS-publikationers betegnelse begynder med DS efterfulgt af et eller flere præfikser og et nr., fx DS 383, DS/EN 5414 osv. Hvis der efter nr. er angivet et A eller Cor, betyder det, enten at det er et tillæg eller et rettelsesblad til hovedstandarden, eller at det er indført i hovedstandarden. DS-betegnelse angives på forsiden. Overensstemmelse med anden publikation: Overensstemmelse kan enten være IDT, EQV, NEQ eller MOD IDT: Når publikationen er identisk med en given publikation. EQV: Når publikationen teknisk er i overensstemmelse med en given publikation, men præsentationen er ændret. NEQ: Når publikationen teknisk eller præsentationsmæssigt ikke er i overensstemmelse med en given standard, men udarbejdet på baggrund af denne. MOD: Når publikationen er modificeret i forhold til en given publikation.

3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN February 2014 ICS English Version Internal blinds - Protection from strangulation hazards - Requirements and test methods for safety devices Stores intérieurs - Protection contre les risques de strangulation - Exigences et méthodes d'essai pour les dispositifs de sécurité Innere Abschlüsse - Schutz vor Strangulationsgefahren - Anforderungen und Prüfverfahren für Sicherheitseinrichtungen This European Standard was approved by CEN on 26 October CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16434:2014 E

4 EN 16434:2014 (E) Contents Page Foreword Scope Normative references Terms and definitions General Artificial ageing Exposure to UV Mechanical endurance Effect of temperature Tensioning device General Test methods Requirements Breakaway device General Test method Requirements Accumulation device General Test method Requirements Non tangling device General Test method Requirements Inner cord stop General Test method Requirements Additional requirements General Release of small components Impact resistance Information and instruction for installation, use and maintenance General Information Instructions (for retrofitting purpose only) Marking Factory Production Control (FPC) Annex A (informative) Tests to be carried out on safety devices Bibliography

5 EN 16434:2014 (E) Foreword This document (EN 16434:2014) has been prepared by Technical Committee CEN/TC 33 Doors, windows, shutters, building hardware and curtain walling, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2014, and conflicting national standards shall be withdrawn at the latest by August Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This document is part of a series of standards dealing with blinds and shutters for buildings as defined in EN It is the intention that safety devices used in EN conform to EN for component testing and EN for functionality. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. 3

6 EN 16434:2014 (E) 1 Scope This European Standard specifies requirements and test methods for safety devices to be used for protection from strangulation in internal blinds as specified in EN and insect screens as specified in EN These devices might be fitted to internal blinds and insect screens at the time of manufacture or for retrofitting. This European Standard applies to any design of device including the following: tensioning devices; breakaway devices; accumulation devices; non tangling devices; inner cord stops. Although at the time this standard has been published, no product standard exists for draperies, requirements and test methods specified in the present standard may be applied to safety devices used in such products. For clarification purpose, the term internal blinds used in the present standard should mean internal blinds and insect screens. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12216, Shutters, external blinds, internal blinds - Terminology, glossary and definitions EN 13120, Internal blinds - Performance requirements including safety EN 13561, External blinds - Performance requirements including safety EN 14201, Blinds and shutters - Resistance to repeated operations (mechanical endurance) - Methods of testing EN 71-1, Safety of toys - Part 1: Mechanical and physical properties EN ISO , Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO ) EN ISO , Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO ) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12216, EN and EN apply. 4 General In the testing of safety devices, all related parts associated with the protection from strangulation shall be included. 4