Dansk standard Tillæg DS/EN 1997-1/A1 1. udgave 2014-02-03 Eurocode 7: Geoteknik Del 1: Generelle regler Eurocode 7: Geotechnical design Part 1: General rules
DS/EN 1997-1/A1 København DS projekt: M267839 ICS: 91.010.30; 91.070.70; 93.020 Første del af denne publikations betegnelse er: DS/EN, hvilket betyder, at det er en europæisk standard, der har status som dansk standard. Denne publikations overensstemmelse er: IDT med: EN 1997-1:2004/A1:2013. DS-publikationen er på dansk og engelsk. Der er tilføjet danske fodnoter markeret med DK og nummeret. Fodnoterne er vejledende og udgør ikke en del af standarden. 2014-12-18: Der er d.d. foretaget redaktionelle ændringer i dette rettelsesblad. 2015-11-20: Der er d.d. foretaget følgende ændringer: I forbindelse med revisionen af det danske anneks til DS/EN 1997-1 har det været nødvendigt at ændre på den danske oversættelse af definitionerne i punkt 8.1.2.7, 8.1.2.9 og 8.1.2.10 i DS/EN 1997-1/A1:2014. De ændrede definitioner er tilpasset til den terminologi, som der anvendes i det danske anneks. DS-publikationstyper Dansk Standard udgiver forskellige publikationstyper. Typen på denne publikation fremgår af forsiden. Der kan være tale om: Dansk standard standard, der er udarbejdet på nationalt niveau, eller som er baseret på et andet lands nationale standard, eller standard, der er udarbejdet på internationalt og/eller europæisk niveau, og som har fået status som dansk standard DS-information publikation, der er udarbejdet på nationalt niveau, og som ikke har opnået status som standard, eller publikation, der er udarbejdet på internationalt og/eller europæisk niveau, og som ikke har fået status som standard, fx en teknisk rapport, eller europæisk præstandard DS-håndbog samling af standarder, eventuelt suppleret med informativt materiale DS-hæfte publikation med informativt materiale Til disse publikationstyper kan endvidere udgives tillæg og rettelsesblade DS-publikationsform Publikationstyperne udgives i forskellig form som henholdsvis fuldtekstpublikation (publikationen er trykt i sin helhed) godkendelsesblad (publikationen leveres i kopi med et trykt DS-omslag) elektronisk (publikationen leveres på et elektronisk medie) DS-betegnelse Alle DS-publikationers betegnelse begynder med DS efterfulgt af et eller flere præfikser og et nr., fx DS 383, DS/EN 5414 osv. Hvis der efter nr. er angivet et A eller Cor, betyder det, enten at det er et tillæg eller et rettelsesblad til hovedstandarden, eller at det er indført i hovedstandarden. DS-betegnelse angives på forsiden. Overensstemmelse med anden publikation: Overensstemmelse kan enten være IDT, EQV, NEQ eller MOD IDT: Når publikationen er identisk med en given publikation. EQV: Når publikationen teknisk er i overensstemmelse med en given publikation, men præsentationen er ændret. NEQ: Når publikationen teknisk eller præsentationsmæssigt ikke er i overensstemmelse med en given standard, men udarbejdet på baggrund af denne. MOD: Når publikationen er modificeret i forhold til en given publikation.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 1997-1:2004/A1 November 2013 ICS 93.020; 91.010.30 English Version Eurocode 7: Geotechnical design - Part 1: General rules Eurocode 7: Calcul géotechnique - Partie 1: Règles générales Eurocode 7 - Entwurf, Berechnung und Bemessung in der Geotechnik - Teil 1: Allgemeine Regeln This amendment A1 modifies the European Standard EN 1997-1:2004; it was approved by CEN on 8 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1997-1:2004/A1:2013: E
EN 1997-1:2004/A1:2013 (E) Contents Page Foreword...3 1 Modification to the Contents...4 2 Modifications to National annex for EN 1997-1...4 3 Modification to 1.1.2...4 4 Modification to 1.2...5 5 Modification to 1.6...5 6 Modification to Section 8...7 7 Modifications to Section 9... 14 8 Modification to 10.2... 15 9 Modification to 11.4... 15 10 Modification to Annex A title and A.1... 15 11 Modification to A.3.3.4... 16 12 Modifications to A.4... 16 13 Modification to A.5... 17 14 Modification to B.3... 19 2
DS/EN 1997-1/A1:2014 Indholdsfortegnelse Side Forord... 3 1 Ændring til Indholdsfortegnelse... 4 2 Ændringer til nationalt anneks for EN 1997-1... 4 3 Ændring til 1.1.2... 4 4 Ændring til 1.2... 5 5 Ændring til 1.6... 5 6 Ændring til kapitel 8... 7 7 Ændringer til kapitel 9... 14 8 Ændring til 10.2... 15 9 Ændring til 11.4... 15 10 Ændring til anneks A's titel og A.1... 15 11 Ændring til A.3.3.4... 16 12 Ændringer til A.4... 16 13 Ændring til A.5... 17 14 Ændring til B.3... 19 2 (da)
EN 1997-1:2004/A1:2013 (E) Foreword This document (EN 1997-1:2004/A1:2013) has been prepared by Technical Committee CEN/TC 250 Structural Eurocodes, the secretariat of which is held by BSI. This Amendment to the European Standard EN 1997-1:2004 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2014, and conflicting national standards shall be withdrawn at the latest by November 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. 3
DS/EN 1997-1/A1:2014 Forord Dette dokument (EN 1997-1:2004/A1:2013) er udarbejdet af teknisk komité CEN/TC 250, Structural Eurocodes, hvis sekretariat varetages af BSI. Dette tillæg til EN 1997-1:2004 skal inden november 2014 have status som national standard enten ved udgivelse af en identisk tekst eller ved formel godkendelse, og modstridende nationale standarder skal være trukket tilbage senest november 2014. Der gøres opmærksom på, at dele af denne standard kan være genstand for patentrettigheder. CEN kan ikke drages til ansvar for at identificere sådanne rettigheder. I henhold til CEN/CENELEC s interne regler er de nationale standardiseringsorganisationer i følgende lande forpligtet til at implementere denne europæiske standard: Belgien, Bulgarien, Cypern, Danmark, Den Tidligere Jugoslaviske Republik Makedonien, Estland, Finland, Frankrig, Grækenland, Irland, Island, Italien, Kroatien, Letland, Litauen, Luxembourg, Malta, Nederlandene, Norge, Polen, Portugal, Rumænien, Schweiz, Slovakiet, Slovenien, Spanien, Storbritannien, Sverige, Tjekkiet, Tyrkiet, Tyskland, Ungarn og Østrig. 3 (da)
EN 1997-1:2004/A1:2013 (E) 1 Modification to the Contents Page 3 Delete: Section 8 Anchorages and replace with: Section 8 Anchors. 2 Modifications to National annex for EN 1997-1 Page 8 National Annex for EN 1997-1 Delete: 8.5.2(2)P, 8.5.2(3), 8.6(4) and replace with: 8.4(6)P, 8.4(7)P, 8.5.1(1)P, 8.5.1(2)P, 8.5.2(1)P, 8.5.2(2)P, 8.5.2(3)P, 8.5.2(5)P, 8.5.3(1)P, 8.5.3(2)P, 8.5.3(3)P, 8.5.3(4)P, 8.6.2(2)P, 8.6.2(3)P. Delete: A.3.1, A.3.2, A.3.3.1, A.3.3.2, A.3.3.3, A.3.3.4, A.3.3.5, A.3.3.6, and replace with: A.3.1, A.3.2, A.3.3.1, A.3.3.2, A.3.3.3, A.3.3.5, A.3.3.6,. After: A.5, add: A.6. 3 Modification to 1.1.2 Page 9 1.1.2 Scope of EN 1997-1 Delete in 1.1.2(2): 4
DS/EN 1997-1/A1:2014 1 Ændring til Indholdsfortegnelse Side 3 Slet: "Kapitel 8 Forankringer" og erstat med: "Kapitel 8 Ankre". 2 Ændringer til nationalt anneks for EN 1997-1 Side 8 Nationalt anneks for EN 1997-1 Slet: "8.5.2(2)P, 8.5.2(3), 8.6(4)" og erstat med: "8.4(6)P, 8.4(7)P, 8.5.1(1)P, 8.5.1(2)P, 8.5.2(1)P, 8.5.2(2)P, 8.5.2(3)P, 8.5.2(5)P, 8.5.3(1)P, 8.5.3(2)P, 8.5.3(3)P, 8.5.3(4)P, 8.6.2(2)P, 8.6.2(3)P". Slet: " A.3.1, A.3.2, A.3.3.1, A.3.3.2, A.3.3.3, A.3.3.4, A.3.3.5, A.3.3.6," og erstat med: " A.3.1, A.3.2, A.3.3.1, A.3.3.2, A.3.3.3, A.3.3.5, A.3.3.6,". Efter: " A.5", tilføj: " A.6". 3 Ændring til 1.1.2 Side 9 1.1.2 Emne for EN 1997-1 Slet i 1.1.2(2): 4 (da)