Dansk standard DS/EN 10088-4 2. udgave 2011-08-19 Rustfrie stål Del 4: Tekniske leveringsbetingelser for plader og bånd af korrosionsbestandige stål til konstruktionsformål Stainless steels Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes
DS/EN 10088-4 København DS projekt: M258052 ICS: 77.140.20; 77.140.50 Første del af denne publikations betegnelse er: DS/EN, hvilket betyder, at det er en europæisk standard, der har status som dansk standard. Denne publikations overensstemmelse er: IDT med: EN 10088-4:2009. DS-publikationen er på dansk og engelsk. Denne publikation erstatter: DS/EN 10088-4:2009 og DS/EN 10088-4/ZA:2010 som kun forelå i engelsksproget version. Der er ikke foretaget ændringer i denne nye udgave, ud over at den danske oversættelse er indføjet. I tilfælde af tvivl om korrektheden af den danske oversættelse henvises til den engelske version. DS-publikationstyper Dansk Standard udgiver forskellige publikationstyper. Typen på denne publikation fremgår af forsiden. Der kan være tale om: Dansk standard standard, der er udarbejdet på nationalt niveau, eller som er baseret på et andet lands nationale standard, eller standard, der er udarbejdet på internationalt og/eller europæisk niveau, og som har fået status som dansk standard DS-information publikation, der er udarbejdet på nationalt niveau, og som ikke har opnået status som standard, eller publikation, der er udarbejdet på internationalt og/eller europæisk niveau, og som ikke har fået status som standard, fx en teknisk rapport, eller europæisk præstandard DS-håndbog samling af standarder, eventuelt suppleret med informativt materiale DS-hæfte publikation med informativt materiale Til disse publikationstyper kan endvidere udgives tillæg og rettelsesblade DS-publikationsform Publikationstyperne udgives i forskellig form som henholdsvis fuldtekstpublikation (publikationen er trykt i sin helhed) godkendelsesblad (publikationen leveres i kopi med et trykt DS-omslag) elektronisk (publikationen leveres på et elektronisk medie) DS-betegnelse Alle DS-publikationers betegnelse begynder med DS efterfulgt af et eller flere præfikser og et nr., fx DS 383, DS/EN 5414 osv. Hvis der efter nr. er angivet et A eller Cor, betyder det, enten at det er et tillæg eller et rettelsesblad til hovedstandarden, eller at det er indført i hovedstandarden. DS-betegnelse angives på forsiden. Overensstemmelse med anden publikation: Overensstemmelse kan enten være IDT, EQV, NEQ eller MOD IDT: Når publikationen er identisk med en given publikation. EQV: Når publikationen teknisk er i overensstemmelse med en given publikation, men præsentationen er ændret. NEQ: Når publikationen teknisk eller præsentationsmæssigt ikke er i overensstemmelse med en given standard, men udarbejdet på baggrund af denne. MOD: Når publikationen er modificeret i forhold til en given publikation.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 10088-4 April 2009 ICS 77.140.20; 77.140.50 English Version Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes Aciers inoxydables - Partie 4: Conditions techniques de livraison des tôles et bandes en acier résistant à la corrosion pour usage de construction This European Standard was approved by CEN on 21 February 2009. Nichtrostende Stähle - Teil 4: Technische Lieferbedingungen für Blech und Band aus korrosionsbeständigen Stählen für das Bauwesen CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10088-4:2009: E
EN 10088-4:2009 (E) Contents Foreword...3 1 Scope...5 2 Normative references...5 3 Terms and definitions...6 4 Designation and ordering...6 4.1 Designation of steel grades...6 4.2 Order designation...6 5 Classification of grades...7 6 Requirements...8 6.1 Steelmaking process...8 6.2 Delivery condition...8 6.3 Chemical composition...8 6.4 Chemical corrosion properties...8 6.5 Mechanical properties...8 6.6 Surface quality...9 6.7 Internal soundness...9 6.8 Formability at room temperature...9 6.9 Dimensions and tolerances on dimensions and shape...9 6.10 Calculation of mass and tolerances on mass...9 7 Inspection and testing...9 7.1 General...9 7.2 Agreement on tests and inspection documents... 10 7.3 Specific inspection and testing... 10 7.4 Test methods... 10 7.5 Retests... 11 8 Evaluation of Conformity... 11 8.1 General... 11 8.2 Initial type testing... 11 8.3 Factory production control (FPC)... 12 9 Marking... 14 10 Dangerous substances... 14 Annex A (informative) Guidelines for further treatment (including heat treatment) in fabrication... 34 Annex B (normative) Applicable dimensional standards... 38 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/106/EEC, EU Construction Products Directive... 39 Bibliography... 45 Page 2
DS/EN 10088-4:2011 Indholdsfortegnelse Forord... 3 1 Anvendelsesområde... 5 2 Normative referencer... 5 3 Termer og definitioner... 6 4 Betegnelse og bestilling... 6 4.1 Betegnelse af ståltyper... 6 4.2 Oplysninger i købsaftalen... 6 5 Klassifikation af ståltyper... 7 6 Krav... 8 6.1 Stålfremstillingsproces... 8 6.2 Leveringstilstand... 8 6.3 Kemisk sammensætning... 8 6.4 Korrosionskemiske egenskaber... 8 6.5 Mekaniske egenskaber... 8 6.6 Overfladebeskaffenhed... 9 6.7 Indre beskaffenhed... 9 6.8 Deformerbarhed ved rumtemperatur... 9 6.9 Dimensioner og dimensions- og formtolerancer... 9 6.10 Beregning af masse og tolerancer for masse... 9 7 Inspektion og prøvning... 9 7.1 Generelt... 9 7.2 Aftale om prøvninger og inspektionsdokumenter... 10 7.3 Specifik inspektion og prøvning... 10 7.4 Prøvningsmetoder... 10 7.5 Omprøvninger... 11 8 Vurdering af overensstemmelse... 11 8.1 Generelt... 11 8.2 Førstegangsprøvning... 11 8.3 Fabrikkens egen produktionskontrol (FPC)... 12 9 Mærkning... 14 10 Farlige stoffer... 14 Anneks A (informativt) Retningslinjer for yderligere behandling (herunder varmebehandling) under fremstilling... 34 Anneks B (normativt) Relevante dimensionsstandarder... 38 Anneks ZA (informativt) Sammenhæng mellem denne europæiske standard og de væsentlige krav i direktiv 89/106/EØF, byggevaredirektivet... 39 Bibliografi... 45 Side 2 (da)
EN 10088-4:2009 (E) Foreword This document (EN 10088-4:2009) has been prepared by Technical Committee ECISS/TC 23 Steels for heat treatment, alloy steels and free-cutting steels - Qualities and dimensions, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by January 2011. EN 10088, under the general title "Stainless steels", consists of the following parts: Part 1: List of stainless steels (including a table of European Standards, in which these stainless steels are further specified, see Annex D); Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes; Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes; Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes; Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes. The European Committee for Standardisation (CEN) draws attention to the fact that it is claimed that compliance with this document may involve the use of patents concerning two steel grades. The holder of these patent rights has assured the CEN that he/she is willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with CEN [and/or] CENELEC. Information may be obtained from: Sandvik AB SE-811 81 SANDVIKEN Sweden for grade 1.4477 Outokumpu Stainless AB SE-77480 AVESTA Sweden for grade 1.4162 CEN takes no position concerning the evidence, validity and scope of this patent right. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). 3
DS/EN 10088-4:2011 Forord Dette dokument (EN 10088-4:2009) er udarbejdet af teknisk komité ECISS/TC 23, Steels for heat treatment, alloy steels and free-cutting steels Qualities and dimensions, hvis sekretariat varetages af DIN. Denne europæiske standard skal inden oktober 2009 have status som national standard, enten ved at der udgives en identisk tekst, eller ved formel godkendelse, og modstridende nationale standarder skal være trukket tilbage senest januar 2011. EN 10088 med den generelle titel "Rustfrie stål" består af følgende dele: Del 1: Liste over rustfrie stål (med en tabel over europæiske standarder, hvori disse rustfrie stål er specificeret yderligere, se anneks D). Del 2: Tekniske leveringsbetingelser for plader og bånd af korrosionsbestandige stål til generelle formål. Del 3: Tekniske leveringsbetingelser for halvfabrikata, stænger, valsetråd, tråd, profiler og blankstål af korrosionsbestandige stål til generelle formål. Del 4: Tekniske leveringsbetingelser for plader og bånd af korrosionsbestandige stål til konstruktionsformål. Del 5: Tekniske leveringsbetingelser for stænger, valsetråd, tråd, profiler og blankstål af korrosionsbestandige stål til konstruktionsformål. Den europæiske standardiseringsorganisation CEN henleder opmærksomheden på, at overensstemmelse med dette dokument kan betyde, at der anvendes to patenterede ståltyper. Patenthaverrne har forsikret CEN om, at de er villige til at forhandle licenser under rimelige og ikke-diskriminerende vilkår og betingelser med ansøgere over hele verden. Erklæringer fra patenthaveren er i denne forbindelse registreret hos CEN [og/eller] CENELEC. Oplysninger kan fås ved henvendelse til: Sandvik AB SE-811 81 SANDVIKEN Sverige for type 1.4477 Outokumpu Stainless AB SE-77480 AVESTA Sverige for type 1.4162 CEN tager ikke stilling til bevis, gyldighed og anvendelsesområde for denne patentrettighed. Der gøres opmærksom på muligheden for, at dele af dette dokument kan være genstand for andre patentrettigheder end rettighederne nævnt ovenfor. CEN kan ikke drages til ansvar for at identificere sådanne rettigheder. Denne europæiske standard er udarbejdet af CEN i henhold til et mandat fra Europa-Kommissionen og EFTA, og den underbygger væsentlige krav i ét eller flere EF-direktiver. 3 (da)
EN 10088-4:2009 (E) For relationship with EC Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. 4
DS/EN 10088-4:2011 Sammenhængen med evt. EF-direktiver er angivet i anneks ZA, der er en integreret del af dette dokument. I henhold til CEN/CENELEC s interne regler er de nationale standardiseringsorganisationer i følgende lande forpligtet til at implementere denne europæiske standard: Belgien, Bulgarien, Cypern, Danmark, Estland, Finland, Frankrig, Grækenland, Irland, Island, Italien, Letland, Litauen, Luxembourg, Malta, Nederlandene, Norge, Polen, Portugal, Rumænien, Schweiz, Slovakiet, Slovenien, Spanien, Storbritannien, Sverige, Tjekkiet, Tyskland, Ungarn og Østrig. 4 (da)
EN 10088-4:2009 (E) 1 Scope The scope of this part of EN 10088 is to specify the technical delivery conditions for hot or cold rolled sheet/plate and strip of standard and special grades of corrosion resisting stainless steels for construction purposes in addition to the general technical delivery conditions specified in EN 10021. This European Standard does not apply to components manufactured by further processing of the product forms listed above with quality characteristics altered as a result of such further processing. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10002-1, Metallic materials - Tensile testing - Part 1: Method of test at ambient temperature EN 10002-5, Metallic materials - Tensile testing - Part 5: Method of testing at elevated temperature EN 10021, General technical delivery requirements for steel products EN 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10045-1, Metallic materials - Charpy impact test - Part 1: Test method EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definition of steel products EN 10088-1:2005, Stainless steels - Part 1: List of stainless steels EN 10088-2, Stainless steels Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10163-2, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plates and wide flats EN 10168:2004, Steel products Inspection documents List of information and description EN 10204, Metallic products - Types of inspection documents CEN/TR 10261, Iron and steel Review of available methods of chemical analysis EN 10307, Non-destructive testing - Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method) EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels - Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulphuric acid (ISO 3651-2:1998) EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2005) 5
DS/EN 10088-4:2011 1 Anvendelsesområde Denne del af EN 10088 har til formål at specificere de tekniske leveringsbetingelser for varm- eller koldvalset plade og bånd af standardtyper og specielle typer af korrosionsbestandige rustfrie stål til konstruktionsformål ud over de generelle tekniske leveringsbetingelser i EN 10021. Denne europæiske standard gælder ikke for komponenter fremstillet ved videreforarbejdning af produktformerne angivet ovenfor med ændrede kvalitetskarakteristika som følge af denne yderligere forarbejdning. 2 Normative referencer Følgende dokumenter er absolut nødvendige for anvendelsen af dette dokument. For daterede referencer gælder kun den nævnte udgave. For udaterede referencer gælder den nyeste udgave af det pågældende dokument (med tillæg). EN 10002-1, Metallic materials Tensile testing Part 1: Method of test at ambient temperature EN 10002-5, Metallic materials Tensile testing Part 5: Method of testing at elevated temperature EN 10021, General technical delivery requirements for steel products EN 10027-1, Designation systems for steels Part 1: Steel names EN 10027-2, Designation systems for steels Part 2: Numerical system EN 10045-1, Metallic materials Charpy impact test Part 1: Test method EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definition of steel products EN 10088-1:2005, Stainless steels Part 1: List of stainless steels EN 10088-2, Stainless steels Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10163-2, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 2: Plates and wide flats EN 10168:2004, Steel products Inspection documents List of information and description EN 10204, Metallic products Types of inspection documents CEN/TR 10261, Iron and steel Review of available methods of chemical analysis EN 10307, Non-destructive testing Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method) EN ISO 377, Steel and steel products Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in media containing sulphuric acid (ISO 3651-2:1998) EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1:2005) 5 (da)
EN 10088-4:2009 (E) EN ISO 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2005) EN ISO 6508-1, Metallic materials - Rockwell hardness test - Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-1:2005) EN ISO 9001:2008, Quality management systems - Requirements (ISO 9001:2008) EN ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 stainless steels the definition in EN 10088-1:2005 applies 3.2 corrosion resisting steels steels with at least 10,5 % Cr and max. 1,20 % C if their resistance to corrosion is of primary importance 3.3 product forms the definitions in EN 10079:2007 apply 3.4 types of heat-treatment the definitions in EN 10052:1993 apply 3.5 standard grades grades with a relatively good availability and a wider range of application 3.6 special grades grades for special use and/or with limited availability 4 Designation and ordering 4.1 Designation of steel grades The steel names and steel numbers (see Tables 1 to 4) are allocated in accordance with EN 10027-1 and EN 10027-2 respectively. 4.2 Order designation The complete designation for ordering a product according to this European Standard shall contain the following information: a) the desired quantity; b) the product form (e.g.: strip or sheet/plate); 6
DS/EN 10088-4:2011 EN ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method (ISO 6507-1:2005) EN ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-1:2005) EN ISO 9001:2008, Quality management systems Requirements (ISO 9001:2008) EN ISO 14284, Steel and iron Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996) 3 Termer og definitioner I dette dokument gælder følgende termer og definitioner. 3.1 rustfrie stål definitionen i EN 10088-1:2005 gælder 3.2 korrosionsbestandige stål stål med mindst 10,5 % Cr og højst 1,20 % C, hvis korrosionsbestandigheden er den væsentligste egenskab 3.3 produktformer definitionerne i EN 10079:2007 gælder 3.4 typer af varmebehandling definitionerne i EN 10052:1993 gælder 3.5 standardstål ståltyper med relativt god tilgængelighed og et bredt anvendelsesområde 3.6 specialstål ståltyper til speciel anvendelse og/eller med begrænset tilgængelighed 4 Betegnelse og bestilling 4.1 Betegnelse af ståltyper Stålnavnene og stålnumrene (se tabel 1 til 4) er tildelt i overensstemmelse med henholdsvis EN 10027-1 og EN 10027-2. 4.2 Oplysninger i købsaftalen Den fuldstændige betegnelse ved bestilling af et produkt i henhold til denne europæiske standard skal indeholde følgende oplysninger: a) ønsket mængde b) produktform (fx bånd eller plade) 6 (da)