Large main line filter

Transkript

1 F5000 (oil free) Components preparation and pressure adjustment / main line unit / air Overview For oil free compressor, stainless steel vessel is used to eliminate anxiety of rust occurrence, and to supply perfect clean high quality air. Features (1) SUS vessel provided For oil free, SUS304 is used for all models. (2) Incorporated energy saving element (3) Unique drainage Forcible discharge method, while new automatic drain with air loss zero is used. (4) Remote control possible Element replacement information is issued by differential pressure switch outputting alarm signal. (5) Simple element replacement Remove the top flange, and just turn the screw on the element. CONTENTS Product introduction 198 pplicable circuit 200 Safety precautions 202 Pre- (F5000P) 204 Oil removing (F5000S) 208 High performance oil removing (F5000M) 212 ctivated charcoal (F5000X) 2 nic sensor Pressure 197

2 F5000 Series Providing total oil-free specifications from refrigerating air dryer to by incorporating stainless steel vessel Stainless steel vessel incorporated for all models (SUS304) Truly clean air is supplied without rust forming. Light weight (10 to 20% (CKD comparison)) Easily replace element screw method is used for element installation, so the element is replaced by removing the upper flange. Stainless steel is used for threads, so it does not stick due to rust. nic sensor Pressure Remote control possible n indicator with a differential pressure switch is standard, installed on the front. The element replacement interval is confirmed beforehand. n alarm signal is output from the differential switch, providing an accurate reading and enabling remote control. Easy installation Installation legs have been prepared as a standard, making piping work easy. (Excluding F50) The legs are removed when not required. utomatic drain with no air loss sensor prevents wasted air consumption (Provided as standard on P and S types) The highly reliable drain lower end sensor and solenoid valve have been integrated in this new energy-saving drain discharger. While air is discharged with the drainage when using the float type or disk type drain discharger, this product detects the lower water level during drainage discharge, so air is not wasted and discharged when discharging the drainage. n alarm signal is output, enabling remote control. (200 VC power supply is required) Drain Drain sensor Tank Lower water level is detected, and discharge starts after set time has elapsed Diaphragm Drainage Lower water level is detected again and drainage stops 198

3 Long life, low pressure loss element Element service life curve p Conventional products New type Element replacement One year or more in normal state The pressure loss is half of the conventional. F5000 Series The element is replaced when the pressure drops to The element life is one year or longer when used under normal conditions. New CKD main line powerfully repels water and oil. "Polysilicate glass microfibers" used in the filtration layer powerfully repel water and oil, allowing the pressure drop and running costs to be minimized. PType B Conventional Conventional glass microfibers absorb water and oil, so pressure easily drops, filtration performance decreases, and operation costs increase. Main line Oil mist Oil mist Oil mist (Pre-) (Oil removing ) (High performance oil removing ) (ctivated charcoal ) For air dryer pre Protecting expensive components For oil inhibited circuit For odor inhibited circuit Contaminating substances 3μm or larger are removed Water drip separation rate 95% Conventional absorbs water and oil. SType Contaminating substances 0.3μm or larger are removed Oil up to secondary side oil concentration of 0.5mg/m 3 (21 C) is removed The high 96% gap rate in the element fibers realizes a low pressure loss and long life MType Contaminating substances 0.01μm or larger are removed Oil up to secondary side oil concentration of 0.01mg/m 3 (21 C) is removed XType bsorb particles with activated carbon Vapor oil and odors up to secondary side oil concentration of 0.003mg/m 3 (21 C) is removed nic sensor Pressure CKD's original chemical fiber structure permanent element has been adopted for the 3μm element. This structure dose not clog easily and realized long-life and low pressure-loss. Polysilicate micro fibers quickly separate oil and limit pressure loss. long life is realized with a 96% gap rate in element fibers. Cylindrically wound particle activated carbon absorbs oil vapor molecules and odor molecules with a low pressure loss. This is configured of a high concentration of activated carbon, so a long element life is realized. 199

4 nic sensor Pressure F5000 Series Typical circuit used in main line Oil-free compressor Turbo type Screw type Lubrication type compressor Screw type Main line P type Main line P type *1 *1 *1 *1 *1 *1 S type S type M type Heatless M type Heatless dryer dryer Main line P type Main line P type S type S type M type M type X type X type *2 Oil free general dry air JIS grade (3).6.6 Oil free dry clean air JIS grade Oil free Food industry dry odorless Pharmaceutical industry clean air gitation / transport / dry / packing / brewing air JIS grade Oil free ultra dry clean air JIS grade *2 General dry air JIS grade(3).6.6 Oil removal dry clean air JIS grade Oil removal dry odorless clean air JIS grade Oil removal ultra dry clean air JIS grade tool air drill / air screw driver Labor saving device / components Pneumatic jigs and tools chuck / air vice Precision part cleaning air blow Instrumentation Measurement Logic control movable element / pure fluid element industry Luxury painting Furnace gas dry Ozone generator High voltage generator insulation gas dry High voltage breaker injection air dry Central control instrumentation tool air drill / air screw driver Labor saving device / components Pneumatic jigs and tools chuck / air vice Precision part cleaning air blow Instrumentation Measurement Logic control movable element / pure fluid element industry Food industry Pharmaceutical industry gitation / transport / dry / packing / brewing air Luxury painting Furnace gas dry Ozone generator High voltage generator insulation gas dry High voltage breaker injection air dry Central control instrumentation *1. Use rust proof pipes (zinc plating, lining and stainless steel pipes, etc.). If there is a high probability that a lot of rust and peelings could be generated in the inside of pipe, install a main F5000 Series P type to the primary side of dryer. *2. Install a removing impurities and contaminants generated in the pipe just before components. Compressed air quality grade JIS B : 2000 Grade Max. particle diameter (μm) Minimum pressure dew point ( C) Max. oil concentration (mg/m 3 ) For example, Grade shows the grade that solid particle 0.1μm, pressure dew point +3 C and oil content density 0.01mg/m

5 Wide variation 4 types 40 models are available. The appropriate model can be selected per flow rate and air quality. F50P-50 F5000 Series pplicable circuit 0 Flow rate code m 3 /min. (NR) Element type P P type 50 Flange 2B m 3 /min. (NR) 48m 3 /min. (NR) 64m 3 /min. (NR) S M X S type M type X type Flange 3B Flange 4B m 3 /min. (NR) 96m 3 /min. (NR) 128m 3 /min. (NR) 0m 3 /min. (NR) 192m 3 /min. (NR) 256m 3 /min. (NR) 200 Easy design equipment Each series with same flow rate has same dimension and same port size to enable easy design and installation. Type can be changed only with changing the element. nic sensor Pressure 201

6 Main line component (main line ) Safety precautions lways read this section before starting use. Refer to Intro 67 for general precautions. F5000 Series WRNG The manufacturer cannot be held liable in the following cases: WRNG void direct sunlight and rain water. The resin parts, etc., could deteriorate and break. void use in the area containing corrosive gas. Use this product within the range of working temperature. Do not use the product where it could freeze. The accumulated drainage could freeze and damage the product. Do not use in dangerous places (atmosphere with risk of explosions, etc.). The inlet temperature should be kept as low as possible. The oil removing rate will drop if the temperature is high. Manufacturer's Liability Working environment Serious errors in use occur due to the operator. Illegal modifications or repairs using nonstandard parts by user. 0 C 61 C nic sensor Pressure CUTION "Class 2 pressure vessel" according to "safety regulation of boiler and pressure vessel" in Occupational Safety Sanitation Laws is applied in model no. F5032 to F5256. Model F5032 to F5256 have a Class 2 pressure vessel withstand pressure proof certificate. This certificate must be kept in safe-keeping while using this product. (pplications to the Labor Standards Supervision Office are no longer required in Japan.) This product may be used only in Japan. (Consult with CKD for use overseas.) Install this product on a stable, flat surface not subject to vibration. Do not step onto this product. When piping, remove cutting oil and rust proof oil, etc. Secure enough space for maintenance and inspection. Installation mm and over 202

7 F5000 Series Individual Precautions The element and differential pressure indicator could be damaged if air is passed suddenly. When installing valves, etc., before and after this product, do not operate the valves suddenly. Do not install this in a where a reverse flow could occur or where impact could be applied easily. Flash the drain piping before installing to remove any foreign matter from inside. Connect a tube pipe, etc., to the drain port. Drainage is discharged with pressure, so securely fix the piping at the drain port so that drainage does not splatter. If the drain port piping slopes upward, the minimum working pressure will increase by 0.01 per 1m. Make sure that the upward sloping piping does not exceed 5m. CUTION differential pressure indicator is provided as standard. Use this to judge element life. Do not flow air in reverse. Do not pressurize suddenly. Otherwise, original performance may not be attained. Sudden pressurization Reverse Operation (utomatic drain) Use within a range of ±10% of the rated voltage 200 VC. Use this product within working pressure range. The drain outlet closes when the power is OFF, so drainage will not be discharged. Drainage will be discharged only when power is ON, so leave the power ON at all times during use. CUTION The air life is spent when the pressure drops to or after one year of use, whichever is sooner. Change the all elements when the life span is reached. X Series can not control service life with the differential pressure. Replace the after 1000 hours of use or when the deodorizing effect is lost. Inspection and maintenance (utomatic drain: DBV1003) Check whether the Power indicator is ON. Check whether the larm indicator is OFF. Press the TEST button, and confirm that drainage is discharged. Note that the alarm mode is entered if the button is held down for more than a minute. (larm is output) nic sensor Pressure larm Power Maintenance and repairs must always be done in nonpressurized state with power turned OFF. Use only genuine repair parts. 203

8 Main line F5000P Series Pre- of air dryer Flow rate range: to 256m 3 /min. (NR) JIS symbol Specifications nic sensor Pressure Model no. Descriptions Treating air flow rate Working fluid Working pressure Withstanding pressure mbient temperature range Filtration rating Pressure drop Initial Regular Element change (Note 2. Note 3.) m3/min. (NR) C μm Element quantity (Note 1) Flange Product weight kg Differential pressure switch Operating differential pressure Contact Maximum contact current Maximum contact voltage VDC Maximum contact capacitance W Maximum contact resistance (including reed switch) mω utomatic drain (model no.: DBV1003) Drain port size Power supply F50P B 38 F5032P B 76 F5048P B 78 F5064P B 107 F5080P B 140 F5096P Compressed air 0.08 to to 60 3 Within B ± pole a contact F5128P B 223 (Note 4) G1/4 or 8 to 10mm hose joint Single phase 200 VC 50/60Hz Note 1. Flange is 10K flange. Note 2. Treating air flow rate is the atmospheric pressure conversion value where inlet pressure is 0.7 and initial pressure drop is Note 3. NR shows conditions where 20 C atmospheric pressure and relative humidity 65%. Note 4. G1/4 allows R1/4 connection. Flow rate compensation coefficient If working pressure is other than 0.7, multiply treated air flow rate by following coefficient. Pressure () Compensation coefficient F50P F5192P F5256P

9 F5000P Series How to order How to order F5 0 P 50 X1 Flow rate code B C Option Note on model no. selection <Example of model number> F50P-50-X1 Model: Main line F5000P Series Flow rate code : m 3 /min. (NR) B : Flange 2B C Option : - reverse direction Note 1 Note 2 Note 3 Note 5 Note 1: "D" automatic drain c is recommended for a working environment where unable to electric wire. Note 2: "L" and "L1" are applicable to F5032P to F5256P. Note 3: Viewed from the front, a standard product has air inlet on the left port, while air outlet on the right port. For "X1", air inlet is provided on the right port, while air outlet is provided on the left port. Note 4: The required performance may not be attained if using at a level less than the selected pressure. lways select the model with the working pressure. Note 5: When ordering several options, indicate the required options in alphabetical order. Symbol Descriptions Flow code m 3 /min. (NR) B Flow rate code Flange 2B 80 Flange 3B 100 Flange 4B C Option Blank Standard products D utomatic drain C (Note 1) E Without automatic drain K Coupling flange attached H English documentation H1 Export packing H2 SUS name L nchor bolt, nut attached (SS400) (Note 2) L1 nchor bolt, nut attached (SUS304) (Note 2) X1 - reverse direction (Note 3) Y2 Product photo nic sensor Pressure 205

10 F5000P Series Dimensions F50P F5032P to F5256P (1202) and over (997) ø x B flange D terminal box Pg7 C G B D F E D terminal box Pg7 utomatic drain DBV1003 utomatic drain DBV1003 G1/4 (parallel male thread) G1/4 (parallel male thread) With ø8 hose joint With ø8 hose joint H nchor bolt hole dimension J 4-øK nic J sensor Pressure Model no. F5032P-80 F5048P-100 F5064P-100 F5080P-150 F5096P-150 F5128P-150 F50P-200 F5192P-200 F5256P-200 Flange 3B Flange 4B Flange 4B B C D ø400 ø400 ø445 ø490 ø560 ø620 ø620 ø675 ø745 E 12-M22 x M22 x 80 -M22 x 80 -M22 x 80 -M24 x M24 x M24 x M24 x M30 x 110 F M M24 G H ø380 ø380 ø440 ø480 ø540 ø610 ø610 ø670 ø730 J K 206

11 Repair parts list F5000P Series Repair parts list Ordering method Gasket Flow rate code m 3 /min. (NR) 32 Gasket F50P-GSKET F5032P-GSKET Element kit F50P-ELEMENT-KIT F5032P-ELEMENT-KIT utomatic drain Element kit F5048P-GSKET F5064P-GSKET F5080P-GSKET F5096P-GSKET F5128P-GSKET F50P-GSKET F5192P-GSKET F5256P-GSKET F5048P-ELEMENT-KIT F5064P-ELEMENT-KIT F5080P-ELEMENT-KIT F5096P-ELEMENT-KIT F5128P-ELEMENT-KIT F50P-ELEMENT-KIT F5192P-ELEMENT-KIT F5256P-ELEMENT-KIT F-DBV C200V utomatic drain nic sensor Pressure 207

12 F5000S Series Protecting expensive components Flow rate range: to 256m 3 /min. (NR) JIS symbol Specifications nic sensor Pressure Model no. Descriptions Treating air flow rate Working fluid Working pressure Withstanding pressure mbient temperature range Filtration rating Secondary side oil concentration Pressure drop Initial Regular Element change (Note 2. Note 3.) m3/min. (NR) C μm mg/m 3 Element quantity (Note 1) Flange Product weight kg Differential pressure switch Operating differential pressure Contact Maximum contact current Maximum contact voltage VDC Maximum contact capacitance W Maximum contact resistance (including reed switch) mω utomatic drain (model no.: DBV1003) Drain port size Power supply F50S B 38 F5032S B 76 F5048S B 78 F5064S B 107 F5080S B 140 F5096S B 7 F5128S Compressed air 0.08 to to (at inlet air 21 C or less) ± pole a contact B 223 (Note 4) G1/4 or ø8 to 10mm hose joint Single phase 200 VC 50/60Hz Note 1. Flange is 10K flange. Note 2. Treating air flow rate is the atmospheric pressure conversion value where inlet pressure is 0.7 and initial pressure drop is Note 3. NR shows conditions where 20 C atmospheric pressure and relative humidity 65%. Note 4. G1/4 allows R1/4 connection. F50S F5192S F5256S Flow rate compensation coefficient If working pressure is other than 0.7, multiply treated air flow rate by following coefficient. Pressure () Compensation coefficient

13 How to order F5 0 S 50 X1 Flow rate code B C Option Note 1 Note 2 Note 3 Note 5 Symbol Descriptions Flow rate code m 3 /min. (NR) C Option Blank D E K H H1 H2 L L1 X1 Y F5000S Series How to order B Flow rate code Flange 2B 80 Flange 3B 100 Flange 4B Standard products utomatic drain C (Note 1) Without automatic drain Coupling flange attached English documentation Export packing SUS name nchor bolt, nut attached (SS400) (Note 2) nchor bolt, nut attached (SUS304) (Note 2) - reverse direction (Note 3) Product photo nic sensor Note on model no. selection Note 1: "D" automatic drain c is recommended for a working environment where unable to electric wire. Note 2: "L" and "L1" are applicable to F5032S to F5256S. Note 3: Viewed from the front, a standard product has air inlet on the left port, while air outlet on the right port. For "X1", air inlet is provided on the right port, while air outlet is provided on the left port. Note 4: The required performance may not be attained if using at a level less than the selected pressure. lways select the model with the working pressure. Note 5: When ordering several options, indicate the required options in alphabetical order. <Example of model number> F50S-50-X1 Model: Main line F5000S Series Flow rate code : m 3 /min. (NR) B : Flange 2B C Option : - reverse direction Pressure 209

14 F5000S Series Dimensions F50S F5032S to F5256S (1202) and over (997) ø x B flange D terminal box Pg7 C G B D F E D terminal box Pg7 utomatic drain DBV1003 utomatic drain DBV1003 G1/4 (parallel male thread) G1/4 (parallel male thread) With ø8 hose joint With ø8 hose joint H nchor bolt hole dimension J 4-øK nic J sensor Pressure Model no. B C D E F G H J K F5032S-80 F5048S-100 F5064S-100 Flange 3B Flange 4B Flange 4B ø400 ø400 ø M22 x M22 x 80 -M22 x 80 M ø380 ø380 ø F5080S-150 F5096S-150 F5128S-150 F50S-200 F5192S ø490 ø560 ø620 ø620 ø675 -M22 x 80 -M24 x M24 x M24 x M24 x 100 ø480 ø540 ø610 ø610 ø F5256S ø M30 x 110 M24 ø

15 Repair parts list F5000S Series Repair parts list Ordering method Gasket Element kit Flow rate code m 3 /min. (NR) Gasket F50P-GSKET F5032P-GSKET F5048P-GSKET F5064P-GSKET F5080P-GSKET F5096P-GSKET F5128P-GSKET F50P-GSKET F5192P-GSKET F5256P-GSKET Element kit F50S-ELEMENT-KIT F5032S-ELEMENT-KIT F5048S-ELEMENT-KIT F5064S-ELEMENT-KIT F5080S-ELEMENT-KIT F5096S-ELEMENT-KIT F5128S-ELEMENT-KIT F50S-ELEMENT-KIT F5192S-ELEMENT-KIT F5256S-ELEMENT-KIT utomatic drain F-DBV C200V utomatic drain nic sensor Pressure 211

16 F5000M Series For oil inhibited circuit Flow rate range: to 256m 3 /min. (NR) JIS symbol Specifications Model no. Descriptions Treating air flow rate Working fluid Working pressure Withstanding pressure mbient temperature range Filtration rating Secondary side oil concentration Pressure drop Initial Regular Element change Element quantity Product weight Differential pressure switch Operating differential pressure Contact (Note 2. Note 3.) m3/min. (NR) C μm mg/m 3 (Note 1) Flange kg F50M B 38 F5032M B 76 F5048M B 78 F5064M-100 F5080M-150 F5096M-150 F5128M Compressed air 0.08 to to (at inlet air 21 C or less) B 6B 6B 6B ± pole a contact F50M F5192M F5256M Maximum contact current Maximum contact voltage Maximum contact capacitance VDC W nic Maximum contact resistance (including reed switch) mω utomatic drain (model no.: C) Drain port size 300 Rc 1/4 sensor Pressure Note 1. Flange is 10K flange. Note 2. Treating air flow rate is the atmospheric pressure conversion value where inlet pressure is 0.7 and initial pressure drop is Note 3. NR shows conditions where 20 C atmospheric pressure and relative humidity 65%. Flow rate compensation coefficient If working pressure is other than 0.7, multiply treated air flow rate by following coefficient. Pressure () Compensation coefficient

17 How to order F5 0 M 50 X1 Flow rate code B Port size C Option Note on model no. selection Note 1 Note 2 Note 4 Note 1: "L" and "L1" are compatible with F5032M to F5256M. Note 2: Viewed from the front, a standard product has air inlet on the left port, while air outlet on the right port. For "X1", air inlet is provided on the right port, while air outlet is provided on the left port. Note 3: The required performance may not be attained if using at a level less than the selected pressure. lways select the model with the working pressure. Note 4: When ordering several options, indicate the required options in alphabetical order. <Example of model number> F50M-50-X1 Model: Main line F5000M Series Flow rate code : m 3 /min. (NR) B : Flange 2B C Option : - reverse direction Symbol Flow code m 3 /min. (NR) C F5000M Series How to order Descriptions B Flow rate code Flange 2B 80 Flange 3B 100 Flange 4B Option Blank E K H H1 H2 L L1 X1 Y2 Standard products Without automatic drain Coupling flange attached English documentation Export packing SUS name nchor bolt, nut attached (SS400) (Note 1) nchor bolt, nut attached (SUS304) (Note 1) - reverse direction (Note 3) Product photo nic sensor Pressure 213

18 F5000M Series Dimensions F50M F5032M to F5256M (1261) and over (1056) ø x B flange D terminal box Pg7 C G B D F E D terminal box Pg7 utomatic drain C Drain port Rc1/4 H utomatic drain C Drain port Rc1/4 nchor bolt hole dimension J 4-øK nic J sensor Pressure Model no. F5032M-80 F5048M-100 F5064M-100 F5080M-150 F5096M-150 F5128M-150 F50M-200 F5192M-200 F5256M-200 Flange 3B Flange 4B Flange 4B B C D ø400 ø400 ø445 ø490 ø560 ø620 ø620 ø675 ø745 E 12-M22 x M22 x 80 -M22 x 80 -M22 x 80 -M24 x M24 x M24 x M24 x M30 x 110 F M M24 G H ø380 ø380 ø440 ø480 ø540 ø610 ø610 ø670 ø730 J K 214

19 Repair parts list F5000M Series Repair parts list Ordering method Gasket Element kit Flow rate code m3/min. (NR) Gasket F50P-GSKET F5032P-GSKET F5048P-GSKET F5064P-GSKET F5080P-GSKET F5096P-GSKET F5128P-GSKET F50P-GSKET F5192P-GSKET F5256P-GSKET Element kit F50M-ELEMENT-KIT F5032M-ELEMENT-KIT F5048M-ELEMENT-KIT F5064M-ELEMENT-KIT F5080M-ELEMENT-KIT F5096M-ELEMENT-KIT F5128M-ELEMENT-KIT F50M-ELEMENT-KIT F5192M-ELEMENT-KIT F5256M-ELEMENT-KIT utomatic drain C utomatic drain nic sensor Pressure 215

20 F5000X Series For odor inhibited circuit Flow rate range: to 256m 3 /min. (NR) JIS symbol Deodorization Specifications Model no. Descriptions Treating air flow rate (Note 2. Note 3.) m 3 /min. (NR) Working fluid Working pressure Withstanding pressure mbient temperature range C Filtration method Secondary side oil concentration mg/m3 Initial pressure drop Element quantity (Note 1) Flange Product weight kg F50X B 38 F5032X B 76 F5048X B 78 F5064X B 107 F5080X B 140 F5096X B 7 F5128X Compressed air 0.08 to to 30 bsorption by activated charcoal (at inlet air 21 C or less) Within Note 1. Flange is 10K flange. Note 2. Treating air flow rate is the atmospheric pressure conversion value where inlet pressure is 0.7 and initial pressure drop is Note 3. NR shows conditions where 20 C atmospheric pressure and relative humidity 65%. 8 6B 223 F50X F5192X F5256X nic sensor Pressure Flow rate compensation coefficient If working pressure is other than 0.7, multiply treated air flow rate by following coefficient. Pressure () Compensation coefficient

21 F5000X Series How to order How to order F5 0 X 50 X1 Flow rate code B Port size C Option Note on model no. selection <Example of model number> F50X-50-X1 Model: Main line F5000X Series Flow rate code : m 3 /min. (NR) B : Flange 2B C Option : - reverse direction Note 1 Note 2 Note 4 Note 1: "L" and "L1" are applicable to F5032X to F5256X. Note 2: Viewed from the front, a standard product has air inlet on the left port, while air outlet on the right port. For "X1", air inlet is provided on the right port, while air outlet is provided on the left port. Note 3: The required performance may not be attained if using at a level less than the selected pressure. lways select the model with the working pressure. Note 4: When ordering several options, indicate the required options in alphabetical order. Symbol Descriptions Flow rate code m 3 /min. (NR) B Flow rate code Flange 2B 80 Flange 3B 100 Flange 4B C Option Blank Standard products K Coupling flange attached H English documentation H1 Export packing H2 SUS name L nchor bolt, nut attached (SS400) (Note 1) L1 nchor bolt, nut attached (SUS304) (Note 1) X1 - reverse direction (Note 2) Y2 Product photo nic sensor Pressure 217

22 F5000X Series Dimensions F50X F5032X to F5256X (1028) and over (823) 315 ø x B flange C G B D F E Rc1/2 Rc1/2 H nchor bolt hole dimension J 4-øK nic J sensor Pressure Model no. B C D E F G H J K F5032X-80 F5048X-100 F5064X-100 F5080X-150 F5096X-150 F5128X-150 F50X-200 F5192X-200 F5256X-200 Flange 3B Flange 4B Flange 4B ø400 ø400 ø445 ø490 ø560 ø620 ø620 ø675 ø M22 x M22 x 80 -M22 x 80 -M22 x 80 -M24 x M24 x M24 x M24 x M30 x 110 M M24 ø380 ø380 ø440 ø480 ø540 ø610 ø610 ø670 ø

23 Repair parts list F5000X Series Repair parts list Ordering method Gasket Flow rate code m 3 /min. (NR) Gasket F50P-GSKET F5032P-GSKET F5048P-GSKET F5064P-GSKET F5080P-GSKET Element kit F50X-ELEMENT-KIT F5032X-ELEMENT-KIT F5048X-ELEMENT-KIT F5064X-ELEMENT-KIT F5080X-ELEMENT-KIT Element kit Note 1. utomatic drain F5000X: None F5096P-GSKET F5128P-GSKET F50P-GSKET F5192P-GSKET F5256P-GSKET F5096X-ELEMENT-KIT F5128X-ELEMENT-KIT F50X-ELEMENT-KIT F5192X-ELEMENT-KIT F5256X-ELEMENT-KIT nic sensor Pressure 219