Hahn KT-EV / KT-EN For front and side entry doors n For all common upstand dimensions from 15 to 3 mm
Hahn KT-EN Universal hinge with upstand fastening option for front and side entry doors Features n For optimal function: snug fit of all bearing and adjustment elements eliminating play and wear. n Lowering and lifting spindle with transport lock. n For all common upstand dimensions from 15 to 3 mm. n Individual parts are securely positioned in hinge bodies therefore, no problems during transport or door assembly. n Efficient adjustment, a single person can make all adjustments. n Greater security thanks to integrated anti-intruder system without additional parts. n Greater comfort due to variable adjustment of sealing pressure without having to raise or remove the door. n KT-EN with upstand fastening option for extra stability. n NEW: also available with self-tapping screws. 0 41,5/44,5 for standard frames
Hahn KT-EV Universal hinge for front and side entry doors Areas of application: For light-weight plastic doors with slender sections: n Main entrance doors n Side entrance doors n Interior doors n Exterior doors n Entrance doors for flats n Opening inwards and outwards n Universally usable Materials n Hinge bodies of extruded aluminium n Rust-proof, wear-resistant bearing pin n KS bearing bushings with teflon additive n No maintenance thanks to self-lubricating properties of the special bearing material used and its outstanding running characteristics n High-quality surface finish n Resistance of bearing to dirt and moisture 1 15 0 41,5 41,5/44,5 41,5/44,5 for very slender frames for slender frames for standard frames 3
Installation instructions 1 Easy to position, drill holes in frame and door (figure shows door with hinges on left). Place hinge on frame and screw down (max. 4 Nm). Install hinge part of the door frame! For self-tapping screws Ø 5 mm 1 1 Easy to position, drill holes in frame and door (figure shows door with hinges on left). Place hinge on frame and screw down (max. 4 Nm).! For standard screws Ø 5 mm 1 1 Insert bearing pin with marking to centre (zero position) in the door hinge part. Secure pin with special screw (max. 4 Nm). Mount door hinge part Screw on door hinge. Use two additional screws if necessary. 3 KT-EN: screw on angle stop at the upstand of the door. 4 Place and slip on hinge cover in the cut-out. Snap cap in place. Screw in lock screw. 1 3 4 4
Adjustment instructions Sealing-pressure adjustment 1.5 mm 4 1 Remove cap. Slightly loosen special screw. 3 Adjust sealing pressure and hold in position. 4 Tighten special screw (max. 4 Nm) and slip on cap. +.5 mm 3 Horizontal adjustment 1 3 1 Loosen lock screw. Remove cover strip. 3 Variable adjustment. 4 Slip on cover strip and tighten lock screw. 4 ± 5 mm Height adjustment Vertical adjustment, variable + 3 mm + 3 mm Carry out height adjustment only on bottom hinge readjust only upper hinges. 5
Load capacity with various degrees of armouring Maximum door weight 8 for very slender frames for slender frames for standard frames for standard frames In case of sections with prechambers, direct installation of screws may cause deformation of the prechamber. mm Steel / Fe 60 kg 80 kg 10 kg 10 kg mm Aluminium 1 mm Steel / Fe 60 kg 80 kg 80 kg 80 kg 68 mm Bridge prechamber in case of direct installation with Hahn step screw. mm Steel / Fe 60 kg 80 kg 10 kg 10 kg mm Aluminium 1 mm Steel / Fe 60 kg 80 kg 80 kg 80 kg With braced prechambers, it is no longer necessary to use lining material as long as the fastening screw goes through the web or just to the side of it. 60 kg 80 kg 10 kg 10 kg 8 Do not install a hinge to sections that do not have any armouring! Even with a third hinge, installed in the middle, it is not possible to use heavier doors. The third hinge only helps to ensure a uniform sealing pressure. The cited door weights pertain to doors that are 1000 x 000 mm and which are exposed to normal stress when mounted on two hinges. This information is subject to proper installation of door and general installation scenarios and therefore we accept no responsibility. If in doubt, contact us. We would gladly advise you. 6
Parts 3 K00F00 1 Item number available on request K00B0040 7 Item number available on request 6 K00E0011 4 K00B0037 5 K00E0009 8 K00K0011 (white) K00K0010 (black) 9 K00E001 EF900051 K700E0004 E330080 1 Frame hinge part Door hinge part KT-EN, adjustment unit pre-assembled with angle stop 3 Door hinge part KT-EV 4 Adjustment unit KT-EV 5 Bearing pin 6 Special screw 7 Bearing bushing with lowering and lifting spindle 8 Cap 9 Cover strip Countersunk head tapping screw 6 x 40 Self-tapping screw Locking screw for cover strip (small) Accessories Drilling jig without tensioner for KT-EV / KT-EN Drilling jig with tensioner for KT-EV / KT-EN Drilling jig without tensioner for KT-EV FIX (FIX in wing and frame) Drilling jig with tensioner for KT-EV FIX (FIX in wing and frame) Automatic bar drilling template for KT-EV / KT-EN, length,300 mm Automatic bar drilling jig for KT-EV FIX, length,300 mm Saw-resistant bearing pin (1 PU = 4 pieces) No. T315A0000 No. T315A0001 No. T315A0F06 No. T315A0F07 No. T415A0001 No. T415A0F07 No. K50A004 Bearing bushes made of maintenance-free PVC containing Teflon do NOT lubricate! 7
Stock numbers KT-EV for standard frame (0 mm hinge base) Upstand range I with self-tapping 15 0 mm screws 15 0 mm 0 mm White RAL 9010 Nr. K07EV000 Nr. K07EV050 White RAL 9016 Nr. K07GV000 Nr. K07GV050 Brown RAL 8077 Nr. K075V000 Nr. K075V050 Upstand range II 18 3 mm 18 3 mm 0 mm White RAL 9010 Nr. K07EV008 Nr. K07EV051 White RAL 9016 Nr. K07GV008 Nr. K07GV051 Brown RAL 8077 Nr. K075V008 Nr. K075V051 KT-EV for slender frames (15 mm hinge base) Upstand range I 15 0 mm 15 0 mm 15 mm White RAL 9010 Nr. K07EV01 Nr. K07EV05 White RAL 9016 Nr. K07GV01 Nr. K07GV05 Brown RAL 8077 Nr. K075V01 Nr. K075V05 Upstand range II 18 3 mm 18 3 mm 15 mm White RAL 9010 Nr. K07EV031 Nr. K07EV053 White RAL 9016 Nr. K07GV031 Nr. K07GV053 Brown RAL 8077 Nr. K075V031 Nr. K075V053 KT-EV for very slender frames (1 mm hinge base) Upstand range I 15 0 mm 15 0 mm 1 mm White RAL 9010 Nr. K07EV003 Nr. K07EV054 White RAL 9016 Nr. K07GV003 Nr. K07GV054 Brown RAL 8077 Nr. K075V003 Nr. K075V054 KT-EN for standard frame (0mm hinge base) Upstand range I 15 0 mm 15 0 mm 0 mm Upstand range II 18 3 mm 18 3 mm 0 mm White RAL 9010 Nr. K06EV000 Nr. K06EV050 White RAL 9016 Nr. K06GV000 Nr. K06GV050 Brown RAL 8077 Nr. K065V000 Nr. K065V050 White RAL 9010 Nr. K06EV008 Nr. K06EV051 White RAL 9016 Nr. K06GV008 Nr. K06GV051 Brown RAL 8077 Nr. K065V008 Nr. K065V051 Dr. Hahn GmbH & Co. KG Trompeterallee 16 170 D-41189 Mönchengladbach Postfach 40 01 09 D-41181 Mönchengladbach Phone + 49 (0) 166 / 954-3 Fax + 49 (0) 166 / 954-444 Internet www.dr-hahn.com E-Mail sales@dr-hahn.com Prsp KT-EV/KT-EN / GB / D-PRO0119 / 04.16 / Subject to technical changes.