DANSK INSTALLATIONSVEJLEDNING DS Pro Lærred Premium Med og uden motor Udpakningsinstruktioner Åben indpakningen forsigtigt og læg indholdet på et stykke pap eller en anden beskyttende overflade for at undgå beskadigelse. Kontroller at pakkens indhold stemmer overens med tilbehørsoversigten på næste side. Kontroller også om de medfølgende komponenter er modtaget ubeskadiget. Brug ikke beskadigede eller defekte dele. Vigtige sikkerhedsoplysninger Montér og brug dette produkt med varsomhed. Læs venligst vejledningen inden påbegyndelse af montering og følg nøje alle instruktioner. Benyt passende sikkerhedsudstyr under montering. Kontakt venligst en kvalificeret installatør for hjælp hvis du ikke forstår vejledningen, er i tvivl om din væg- eller loftkonstruktion eller om sikkerheden ved montering. Brug ikke dette produkt til andre formål, eller i andre konfigurationer end de udtrykkeligt angivne i denne vejledning. Vi fraskriver os hermed ethvert ansvar eller skade som følge af forkert montering eller forkert brug af dette produkt. Kontakt venligst din forhandler ifm. reparation. ADVARSEL! Dette lærred skal være forsvarligt fastgjort til væg eller loft. Hvis det ikke er monteret korrekt, kan det resultere i, at lærredet falder ned og eventuelt beskadiger personer eller udstyr. Bemærk: De skruer og beslag, der følger med denne indpakning, er ikke beregnet til montering i gibsvæg, og du bedes derfor kontakte den lokale isenkræmmer for vejledning om hvilket tilbehør, som egner sig bedst til dette formål. DS-DISPLAY A/S SKELMARKSVEJ 6 2605 BRØNDBY WWW.DS-DISPLAY.DK TELEFON 36 720 720 FAX 36 720 722 1
DANSK BRUGSANVISNING Om brug af lærredet 1. Lærredet skal så vidt muligt køres op i kabinettet, når det ikke er i brug. Sørg for, at der ikke sidder insekter, støv og lignende på lærredet, når det rulles op. 2. Den igangværende rulle-operation må ikke overstige fire minutter. Gør den det vil motoren automatisk stoppe for at undgå overophedning. Efter nedkøling (ca. 10-15 minutter) virker rullefunktionen igen. 3. For at sikre optimal projektions-effekt, skal du være opmærksom på følgende: 3.1 Undgå at kradse og ridse lærredet 3.2 Undgå at røre overfladen på lærredet med dine hænder 3.3 Brug en tør ren klud eller blød børste til rengøring af lærredet 4. Lærredet må ikke monteres i fugtige lokaler. Lærred med motor: VIGTIGT! Tilslut ikke strømmen, før du er helt færdig med monteringen af lærredet Kontrolenhed Fjernbetjening Illustration: Justering af stop Betjening: Du kan bruge enten kontrolenheden eller fjernbetjeningen, når du skal rulle lærredet op og ned. Benyt de tre knapper (Op, Ned, og Stop ). Begge løsninger har tidskontrol under op- og nedrulning, og begge stopper automatisk når endepunktet er nået. Begge løsninger har integreret intelligent powerfunktion, der automatisk træder i kraft, hvis op- og nedrulning overstiger fire minutter. Lærredet stopper med at køre, indtil motoren er nedkølet igen. Justering af automatisk stop (se illustration) For at justere automatisk stop, skal lærredet være fuldt udrullet Nedre grænse: Drej mod uret og bunden af lærredet justeres mod gulvet Øvre grænse: Drej mod uret og bunden af lærredet justeres op mod kassetten 2
DANSK MONTERINGSVEJLEDNING TILBEHØRSOVERSIGT 8x35 mm 5x40 mm 4x8 mm Beslag - 2 stk. Krog - 2 stk Ring - 2 stk. Rawplug - 4 stk. Skrue - 4 stk. Skrue - 2 stk. Step 1 A Vægophæng og montering af kassette B 1. Marker de steder hvor hullerne til beslaget skal placeres. Sørg for at de er i vatter. 2. Forbor hullerne og indsæt rawplugs. Sørg for at rawplugs bankes helt ind i muren. 3. Monter vægbeslaget på væggen med skruer. 1. Tegningen viser vægbeslaget monteret på væggen. C D 1. Tilt kassetten og monter vægbeslaget i skinnen på bagsiden af kassetten, samtidig med at du indsætter låseskruen i bunden af vægbeslaget. 1. Stram skruerne i bunden af vægbeslagene. Det er vigtigt, at skruerne er monteret og spændt korrekt, da lærredet ellers kan falde ned. 3
DANSK Step 2 Loftophæng og montering af kassette E F 1. Ophængsskinnen er fastspændt i korrekt position i henhold til den anbefalede afstand. Fjern den, fra fabrikken, fastspændte skrue og skru i stedet ringene i ophængsskinnerne. 2. Sørg for, at de ikke kan bevæge sig. 1. Tilt kabinettet for nemmere montering. Krogen må ikke placeres for tæt på væggen. Der skal være ca. 50 mm mellem væg og krog. G Strømforsyning: 1. Ved korrekt montering skal der være ca. 10 mm mellem kabinet og væg. Spænding: 100V - 120 V 60Hz / 220-240V 50Hz Power: 130 W (max) 4
ENGLISH INSTALLATION INSTRUCTION DS Pro Screen Premium Manual and electric Unpacking Instructions Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. Important Safety Information Install and operate this product with care. Please read this instruction before beginning the installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation. Please call a qualified installation contractor for help if you don t understand these directions or have any doubts about the safety of the installation. If you are uncertain about the nature of your wall or ceiling, consult a qualified installation contractor. Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaims any and all liability or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product. CAUTION! This screen must be securely attached to the wall or ceiling. If the screen is not properly installed it may fall, resulting in possible injury and/or damage. Note: The mounting components and hardware supplied in this package are not designed for installations on plasterboard walls. If the hardware you need for your installation is not included, please consult your local hardware store for proper mounting hardware for the application. DS-DISPLAY A/S SKELMARKSVEJ 6 2605 BRØNDBY WWW.DS-DISPLAY.DK TELEFON 36 720 720 FAX 36 720 722 5
ENGLISH USER INSTRUCTION About the canvas 1. The screen must, as far as possible, be driven up into the cassette when not in use. Make sure that there are no insects, dust and durt on the canvas when it is rolled up. 2. The current scroll operation must not exceed four minutes. If so, the engine goes off automatically to prevent overheating. After cooling (about 10-15 minutes) the roller function works again. 3. To ensure optimal projection effect, you should be aware of the following: 3.1 Avoid scratching the screen 3.2 Avoid touching the surface of the screen by hand 3.2 Use a dry, clean cloth or soft brush to clean the screen 4. The screen should not be installed in damp rooms. Electric screen: CAUTION! Do not turn on the power before the complete installation of the screen is done. Control unit Remote control Illustration: Adjusting the stop Operation: You can use either the control unit or remote control to operate the screen. Use the three buttons (Up, Down and Stop ) to operate the screen. Both solutions have time control during ups and downs, and both will stop automatically when the end point is reached. Both solutions have integrated intelligent power function that automatically comes into force if the ups and downs operation are going on for more than four minutes. The canvas will stop running until the engine has cooled down again. Adjusting the stop (see illustration) The canvas must be fully extended, to adjust the stop. Lower limit: Turn counterclockwise and the screen is adjusted towards the floor Upper limit: Turn counterclockwise and the screen is adjusted upwards the cassette 6
ENGLISH SUPPLIED PARTS LIST 8x35 mm 5x40 mm 4x8 mm Bracket - 2 pcs. Hook - 2 pcs. Ring - 2 pcs. Plug - 4 pcs. Screw - 4 pcs. Screw - 2 pcs. Step 1 Wall mounting instruction A B 1. Mark the places where the holes for the bracket must be placed. Make sure they are leveled. 2. Drill holes and insert rawlplugs. Make sure no plug is left outside the wall. 3. Mount the wall bracket to the wall with screws. 1. Wall bracket mounted on the wall. C D 1. Tilt the cassette and mount the wall bracket into the slot at the back of the housing while inserting the screw at the bottom of the wall bracket. 1. Tighten the screws in the bottom of the wall bracket. It is important that the screws are installed and tightened properly. Otherwise the screen may fall down. 7
ENGLISH Step 2 Hanging installation - ceiling mounting E F 1. The mounting track is secured with a screw in the correct position according to the recommended distance. Remove the fixed screw and replace it with the ring. 2. Make sure that the mounting track can not move. 1. Tilt the screen housing upward for easy installation. The hook should not be placed too close to the wall. There should be approx. 50 mm between the wall and the hook. G Power supply: 1. For correct installation, there should be approx 10 mm between the housing and the wall. Voltage: Power: 100V - 120V 60Hz / 220V - 240V 50Hz 130 W (max) 8