Project no.: 731114 Project title: Document file: DME-MWI Release Note for DME-MWI.doc Document Title: Release notes for DME-MWI No. Of Pages: 8 Print Date: 2015-07-08 Document Revision Record Rev. Date Author Pages Affected Brief Description of Change 01 040403 JMP All Original issue of document 041126 JH Ver 1.19 and ver 1.20 040331 JH Ver 1.20 -> 1.21 050429 JH Ver 1.21 -> 1.22 Ver 1.22 -> 1.23 Ver 1.23 -> 1.24 Ver 1.25 Ver 1.24 -> 1.26 Ver 1.26 -> 1.27 060126 JH Ver 1.27 -> 1.28 060224 JH Ver 1.28 -> 1.29 060421 JH Ver 1.30 -> 1.33 061113 JH Ver 1.34 -> 1.59 070327 JH Ver.1.62 -> 2.11 131216 HERP Ver 3.21 -> 4.00 140109 HERP Ver 3.21 -> 3.21.1 140109 HERP Ver 4.00 -> 4.01 140129 HERP Ver 3.21.1 -> 3.21.2 140129 HERP Ver 4.01 -> 4.02 140207 HERP Ver 4.02 -> 4.03 140217 HERP Ver 4.03 -> 4.04 140228 HERP Ver 4.04 -> 4.05 140318 HERP Ver 4.05 -> 4.06 140324 HERP Ver 4.06 -> 4.07 140402 HERP Ver 4.07 -> 4.08 140403 HERP Ver 3.21.2 -> 3.21.3 140408 HERP Ver 4.08 -> 4.09 140512 HERP Ver 4.09 -> 4.10 140519 HERP Ver 4.10 -> 4.11 140528 HERP Ver 4.11 -> 4.12 140603 HERP Ver 4.12 -> 4.13 140605 HERP Ver 4.13 -> 4.14 140625 HERP Ver 4.14 -> 4.15 140626 HERP Ver 4.15 -> 4.16 140701 HERP Ver 4.16 -> 4.17
Document Revision Record Rev. Date Author Pages Affected Brief Description of Change 140707 HERP Ver 4.17 -> 4.18 140710 HERP Ver 4.18 -> 4.19 140813 HERP Ver 4.19 -> 4.20 140818 HERP Ver 4.20 -> 4.21 140818 HERP Ver 4.21 -> 4.22 140819 HERP Ver 4.22 -> 4.23 140903 HERP Ver 4.23 -> 4.24 141020 HERP Ver 4.24 -> 4.25 141023 HERP Ver 4.25 -> 4.26 141028 HERP Ver 4.26 -> 4.27 141103 HERP Ver 4.27 -> 4.28 141219 HERP Ver 4.28 -> 4.29 150206 HERP Ver 4.29 -> 4.30 150226 HERP Ver 4.30 -> 4.31 150304 HERP Ver 4.31 -> 4.32 150505 HERP Ver 4.32 -> 4.33 150506 HERP Ver 4.33 -> 4.34 150519 HERP Ver 4.34 -> 4.35 150630 HERP Ver 4.35 -> 4.36 150703 HERP Ver 4.36 -> 4.37 150708 HERP Ver 4.37 -> 4.38 DISTRIBUTION: R&D (4) Service (1) Customers using this version (>= 1 / customer) APPROVED BY: Poul Tarp A/S Technical Manager Poul Tarp 1 DME MWI Release History Release Date Description and Main functions 1.00 26-06-2001 First release for field test 1.12 15-11-2001 AD converter activated. Total counter added. Digital IN activated with SW filter. Remote buttons for tare and end weighing supported. External light indication for weighing status. (steady, tare) Site ID added. Printer support added. Multilanguage added. 1.16 20-11-2001 Special release for MWS-King Pin Only Release notes for DME-MWI Page 2 of 8
1.12 1.17 17-02-2003 Based on Ver. 1.12 Bug fix, language stays after reset. Ver number changed to 1.12 Rev number now showed with date. 1.12 1.18 01-04-2003 Full key pad support added. Gross weight added. Various display text changes. Alibi backup in flash 64kb. Day total printout added. Product ID added. Default site and product ID added. Power-up ON/OFF. Password protection on Service and Calibration. User defined load alarm. Default Calibration/Configuration choice. 1.12 1.19 26-01-2004 Two display type Tilt output Min time between weighing removed. Print number of receipt copy. 1.12 1.20 03-06-2004 Slip printer added. 1.20 1.21 31-03-2005 FTP622 printer added. Change baud rate for printer 1.21 1.22 29-04-2005 Add output to control a pump after pre selected amount 1.22 1.23 2x20 digit display Test program rs485 TAG reader 1.23 1.24 Add profile = 1 Data com. cabindisplay Industri type Add message Shift display type from calib. to service.. 1.22 1.25 NB 1.22 1x16 digit display languages swedish Add new calibration function. 1.24 1.26 Add profile 2 dayreno. Add new calibration function. New I/O expanse board 1.26 1.27 Some bug for profile 1 1.27 1.28 Printing konfic. Cabindisplay 1.28 1.29 1.29 1.30 Storspand 1.30 1.31 Add datanøgle Profil 3 med ny dataformat 1.31 1.32 Bug ved udskrift løbenr. 1.32 1.33 Extern tara ikke aktiv under afslutning af vejning 1.33 1.34 Bug ved tarering 1.35 1.36 Test programmer Release notes for DME-MWI Page 3 of 8
1.37 Flash bedre skrive rutiner 1.38 Underspænding andet bit i status pakker 1.39 Flash bug 1.40 Nye opsætning. Vent start. Tømmetid. Delay på indgange. Indgang neveau. 1.41 Håndbremse og profil 2 ikke lave registreringer 1.42 Gentag tastetur variabel tid Vent start, fjernet Start tømmetid fra indgang Bug ved læsning af tags som starter med et bogstav. 1.43 MWI uden vejesignal. Tagtype Tiris. 1.44 Spand føler deaktiv under tømning 1.45 Tænd fejllampe ved veje spand hvis vejning ikke er startet. 1.46 Indtastning af meddeelse nummer 1.47 Gem spand nummer på tid. Anvendes til dobbelt tømning. Spørge om sække /dunke. 1.48 Dobbelt tømning i display. Højre pil ikke aktiv sammen med en spand på liften. Ved veje spande, fortæl hvilken spand der skal fjernes. 1.49 Bug ved meddeelser 1.50 Bug ved store spande. 1.51 Bloker M tasten Skriv i display hvilken spand der skal fjernes. 1.52 Blink med lampe hvilken spand der skal fjernes. 1.53 Kunde nummer Bloker tag læsning under antal sække. 1.54 Bloker lift under afslutning af vejning. 1.55 Beep under afslut vejning. Ingen meddeelser på sække. Ikke afslutte vejning med en mand på trinbræt. 1.56 Udgang blokker lift kan inviteres. Tag type kan sættes til ingen. Konfiguration indstilles efter kunde nummer. 1.57 Veje celler analog / digital. RS485 port 3 kan indstille paritet. 1.58 Ved modtagelse af ny industri spand laves en ny tarering. 1.59 Service menu delt op i flere under menuer. 1.62 Frakoble vejning. Udgang hejs aktiv, kan inviteres. Gemmer stop vægt Skjul indtastet password I/O test styre varmen 1.63 Default værdier Release notes for DME-MWI Page 4 of 8
2.06 RTX indført T-Net Lift styring Finsk sprog Tiris 4100 taglæser 2.10 Mink foder styring Nye pakketyper fra TOC. 2.11 Tiris 2000 taglæser Gemplus taglæser uden application software + DME application software. 2.12 M tast tænder udgang6 Lift. Registrering med oplysning om ID kommer fra TAG 2.13 Blokering af lift hvis ID ikke findes. Bug i 485 protokol Datanøgle med 48K 2.14 Taglæser Agrid indført. 2.15 Defekt 2.16 Med udvidelses print version D 2.17 Tapio Lammi funktioner 2.18 HCS profil. Shift 6 nulstil total 2.19 Lift styring med product fraktion 2.20 Gen init serie port. TAG type P013 2.21 TAG type Agrid, 10 regel, disable H4002 Bug produkt fraktion 2.22 Konfig altid veje 2.23 Nulstil ID ved valg af sække 2.24 Ålborg profil. Esit veje enhed 2.25 BIR Reset 4* shift 2.26 BIR: IR pack. Stor container Opdater DR liste efter færdig modtaget data Overroll. Frakoble vejning Tekster til lift Autotune agrid Udvidelse af test I/O 2.27 Modtag TAG ved indtastning af ID 2.28 Gensending af registreringer 2.29 TAG Agrid slave request 2.30 JOAB lift styring 2.31 Hurtigere lift styring. Ikke anbefalet til TOC 2.32 Bug ved TOC rettet. 2.33 Timer på analog vejesignal 2.34 Lift: storspand tara uden slet information om stor spand Lift: Slet med SHIFT Lift: afbryd vejning hvis ingen tag læst og vægt er for lille Autotune antenner vent 15min efter power op 3.15 Styring af TILT tekst på display 3.16 06-08-2013 TiltLimit% tilføjet Level Comp. menu Release notes for DME-MWI Page 5 of 8
4.00 16-12-2013 Calibration parameters moved to write protected EEprom locations. Affected parameters are: AKTIV 1-10, NODE N 1-10, "DEFLECTION", "Tiltlimit%", "VEJECELLE", "NR VINDUER", "OFFSET", "COM. PORT" and "AD CONVE. RATE" 3.21.1 09-01-2014 This is a 3.21 Branch! Bug fix of lockup situation, when starting a weighing from the "TOC" during TILT 4.01 09-01-2014 Bug fix of lockup situation, when starting a weighing from the "TOC" during TILT 3.21.2 29-01-2014 This is a 3.21 Branch! Bug fix of: weighing returns 0 when initiated from TOC 4.02 29-01-2014 Bug fix of: weighing returns 0 when initiated from TOC 4.03 07-02-2014 COMlogger support implemented 4.04 17-02-2014 Bug fix of weighing returns 0 when initiated from Actions menu 4.05 28-02-2014 "Verification" parameter moved to not protected EEprom Null calibration parameter for cells subtracted after calibration factor correction 4.06 18-03-2014 Bug fix t-net not working since 4.03 4.07 24-03-2014 Support for remote display type: ESIT RD102 Load cell values with cell zero subtracted will be send to debug out if node host is set to 888 4.08 02-04-2014 Keep site ID when taring is initiated by external input, configurable in I/O menu by: Keep Site ID. Keep Site ID and Free running added to configuration print 3.21.3 03-04-2014 This is a 3.21 Branch! Keep site ID when taring is initiated by external input, configurable in I/O menu by: Keep Site ID. Keep Site ID added to configuration print 4.09 08-04-2014 Auto Zero cells now works even if number of analog windows is set. 4.10 12-05-2014 Detection and notification of comport conflicts implemented. For 1xxx profiles: Request for load cell configuration is implemented Bug fix of the situation when Tarp load cell amp. channel selection is not in pairs. Bug fix of product number missing in feed registrations Bug fix of TOC communication indicator blinking when comlogger enabled. 4.11 19-05-2014 Bug fix of missing ACK for comlogger since revision 4.10 Enable load cell data on com port for debug added to debug menu. Release notes for DME-MWI Page 6 of 8
4.12 28-05-2014 Load cell data on comport for debug now means of 30. Default values changed for Tarp load cell costumers. New values are: o FREERUNNING = ON o NO WINDOW = 30 o NO STEADY = 12 4.13 03-06-2014 Bug fix of load cell data on comport for debug containing wrong data. 4.14 05-06-2014 Support for FAUN lift weight. 4.15 25-06-2014 TAG reader sync. on MWI via expansion board output 0 and input 8 and specific timing for T-net node one. For Cont./Request set to OFF 4.16 26-06-2014 Use of dynamic password implemented. Password duration timeout set to two min. 4.17 01-07-2014 Bug fix of dynamic password timeout. Changed default settings for costumer LIFT TARP 1103 and NO BIN TARP 1115. No of windows = 25, No of steady windows = 4, Steady e * = 0.5, active cells = 1-3, cell 3 cal. value = -1.0 4.18 07-07-2014 Route no. and driver no. added to registrations when ComLogger enabled. Capital letters A-Z available when entering side-id 4.19 10-07-2014 Bug fix of comlogger format for profile 3 (Marius Pedersen) 4.20 13-08-2014 Bug fix of wrong measurements for feed trucks. Timeout implemented for TOC get configuration ( - W A I T - text) New commands added for calibration tool. 4.21 18-08-2014 Bug fix of Timeout for TOC get configuration for feed trucks Activate stream command added for calibration tool. Bug fix Comlogger not working since 4.20 4.22 18-08-2014 Activate stream command for calibration tool corrected. Comlogger now available on COM2 as well. 4.23 19-08-2014 Bug fix TOC not working correctly since 4.20 4.24 03-09-2014 Update linearization table after remote configuration. The TOC command PR now returns configuration even if there has been no changes. First version of dynamic weighing I/O control = DYN Release notes for DME-MWI Page 7 of 8
4.25 20-10-2014 Remote display E changed to show stop weight when not in verification mode. Controle command RR added to reset configuration sequence for PR command Configuration parameter cleanup for PR command. Modifications for dynamic weighing. Partially implemented ref. cell for dynamic weighing Possibility of enabling volume measurement on Fin4 (K34-35) Done in the I/O menu!note From this MWI firmware version ComLogger needs firmware version 2014-10-20 or later. 4.26 23-10-2014 For I/O control = JOAB a hold time is implemented for up and down input signals. Set by SERVICE -> I/O -> INPUT ms. 4.27 28-10-2014 AD converter rate set to 0 always. Volume measurement correction. 4.28 03-11-2014 New customer no. 1250 for suction vehicles 4.29 19-12-2014 All Modifications for dynamic weighing removed. Bug fix. - Gross weighing of big bucket 4.30 06-02-2015 Bug fix. Gross weighing with site id set to off or mix stops the lift on bucket down. 4.31 26-02-2015 Site id with zero entered as the firs digit will contain an * as delimiter between the entered zero/zeroes and the auto added zeroes. New site id mode added: PRE This mode use the default id value as prefix for the site id. Bug fix. Remote configuration of parameters with same first word. 4.32 04-03-2015 Remote configuration interface modifications. 4.33 05-05-2015 Support for tilt sensor on input I2 added. Enable by selecting level compensation type I2 4.34 06-05-2015 Level compensation type I2 changed to work together with TARP load cell amp. compensation (same as Level compensation type ANA but with tilt warning disabled) To disable a tilt direction set the CAL 1 or CAL 2 value to 1000000. 4.35 19-05-2015 Bug fix BIR lift control registrations with ID entered manually only works first time. 4.36 30-06-2015 Remote configuration interface bug fix. Remote TARE command added. 4.37 03-07-2015 Get configuration command (PR) restrictions removed. 4.38 08-07-2015 Possible to select NONE for printer in main menu. Release notes for DME-MWI Page 8 of 8