Transcutaneous Electrical Nerve Stimulation (TENS): TENS is a clinically proven, safe and effective method of providing pain relief.

Introduction Dear Customer Thank you for choosing the Neurotech Recovery - Back. This product was developed by Neurotech to provide a uniquely, convenient way to help manage pain, prevent muscle wastage and aid in muscle rehabilitation. Neurotech Recovery - Back is designed to deliver Transcutaneous Electrical Nerve Stimulation (TENS) for pain management or Neuromuscular Electrical Stimulation (NMES) for muscle rehabilitation. Transcutaneous Electrical Nerve Stimulation (TENS): TENS is a clinically proven, safe and effective method of providing pain relief. INTRODUCTION & CONTACT DETAILS Neuromuscular Electrical Stimulation (NMES): When muscles are not used, they weaken. Weakened muscles can make it difficult to move around and patients can experience difficulty performing certain tasks or worsen the risk of injury. Strengthening these muscles is an important step in a patient s rehabilitation. The following provides instructions for use of both the conductive garments and the controller. Please ensure that you read all of the instructions carefully before using Neurotech Recovery - Back. If you have further questions regarding this product, please contact your health care professional, the distributor who provided you with the Neurotech Recovery - Back, or Neurotech at the address/phone number below. Yours sincerely, The Neurotech Team If you have questions or require further information please contact: neurotech Rep of Ireland: Freephone - 1800 11 11 Bio-Medical Research Ltd. Northern Ireland/UK: Lo-call - 084 600 1332 Parkmore Business Park West, International Tel.: +33 (0)91 774 377 Galway, Web: www.neurotechgroup.com Ireland. 2

Table of Contents 1.0 Safety Information.................................................... 4 1.1 Contraindications, Warnings and Precautions............................. 2.0 Frequently Asked Questions............................................ 8 3.0 Pack Contents........................................................ 10 3. 1 Neurotech Plus Controls................................................ 11 3.2 Neurotech Plus Controller Display....................................... 13 4.0 Neurotech Recovery - Back Garments.................................. 14 4. 1 Preparing a Back Treatment............................................ 14 4.2 Back Garment Placement............................................... 1 4.3 Preparing an Abdominal Treatment...................................... 16 4.4 Abdominal Garment Placement......................................... 17.0 Using the Neurotech Plus Controller................................... 18 6.0 Problem Solving Guide................................................ 20 6. 1 System Maintenance & Storage.......................................... 21 6.2 Caring for the Garment................................................ 22 6.3 Caring for the Electrodes.............................................. 22 7.0 Technical Information & Accessories................................... 23 7. 1 Electrical Specifications................................................ 2 7.2 Warranty............................................................. 2 8.0 Program Information................................................. 26 TABLE OF CONTENTS 3

1.0 Safety Information Validity The information and technical data contained in this document relates to the Neurotech Recovery - Back product supplied with this manual. The information and technical data disclosed in this document are proprietary to Neurotech and may be used and disseminated only for the purposes and to the extent specifically authorised in writing by the company. Disclaimers All equipment manufactured and sold by Neurotech is rigorously checked and tested prior to shipment. However, the use of this equipment is outside of the control of the company. Neurotech only accept responsibility for the safety, reliability and performance of the equipment when it is operated in accordance with the instructions herein and within the given specifications. Therefore, the user must bear full responsibility for any actions arising out of the use or misuse of this equipment. Any modifications, repairs or servicing must be undertaken by authorized Neurotech personnel. The sale and/or operation of this equipment is subject to the legislation in a number of localities. Compliance with this legislation rests with the importer, dealer or user of the equipment, as appropriate. SAFETY INFORMATION Transcutaneous Electrical Nerve Stimulation (TENS) TENS is a pain therapy based on the stimulation of the nerve fibres, via the application of electrical stimuli to the skin. There are two methods: the pain gate theory, which blocks the pain signals to the brain and through the increased release of endorphins, which inhibits the emergence of pain. Neuromuscular Electrical Stimulation (NMES) NMES may be defined as the application of electrical stimulation to the peripheral nervous system to contract a muscle, either through the direct activation of the motor neurons in the mixed peripheral nerve, or indirectly through reflex recruitment. Indications For Use - Neurotech Recovery - Back The device is intended to deliver therapeutic electrical stimulation to the back and abdominal muscles to: Provide symptomatic relief in the treatment of acute and chronic back pain. Prevent or delay the onset of disuse muscle atrophy. Increase muscle strength of the lumbar and abdominal muscles. Aid rehabilitation in back pain patients. 4

1.1 Contraindications, Warnings and Precautions Contraindications You have an electronic implant (e.g. cardiac pacemaker or defibrillator) or suffer from any other heart problem. You are pregnant. You suffer from cancer, epilepsy or are under medical supervision for cognitive dysfunction. The unit is in close proximity (e.g. 1m) to shortwave or microwave therapy equipment. You are connected to high-frequency surgical equipment. Wearing the device necessitates placement over areas at which drugs/medicines are administered by injection (short term or long term) e.g. hormone treatment. Warnings The long-term effects of chronic electrical stimulation are unknown. Place the electrodes and garments ONLY on the lower back or abdomen, as indicated in this manual. Avoid placing the electrodes or belt on the front or sides of the neck, across or through the heart (i.e. one electrode on the front of the chest and one on the back), in the genital region or on the head. Application of electrodes near the thorax may increase the risk of cardiac fibrillation. Avoid any recent scars, broken or inflamed skin, areas of infection or susceptibility to acne, thrombosis or other vascular problems (e.g. varicose veins), or any parts of the body where feeling is limited. Avoid areas of injury or restricted movement (e.g. fractures or sprains). Avoid placing the electrodes directly over metal implants. For hygiene reasons the electrodes and garments are for use only by one person. Do not share with anyone else. Electrodes should be replaced if they no longer stick to the skin. Do not use the abdominal garment if you are wearing a belly-button ring. Remove the ring before you begin a session. Do not use your unit at the same time as any other device which transfers an electrical current into the body (e.g. another muscle stimulator). Cease using your unit if you are feeling light headed or faint. Consult your clinician if this happens. Do not touch the electrodes or metal studs while the unit is switched on. Do not use while driving, operating machinery or cycling. CONTRAINDICATIONS, WARNINGS AND PRECAUTIONS

CONTRAINDICATIONS, WARNINGS AND PRECAUTIONS Precautions - Please wait before using your product until: At least six weeks after the birth of your baby (you must consult your clinician first). One month after an IUD contraceptive device (e.g. coil) has been fitted. At least three months after having a Caesarean (you must consult your clinician first). The heavy days of your period have finished. To reposition electrodes during a session, always pause the programme currently running, unfasten the belt and then refasten it once the position of the electrodes has been adjusted. Caution should be used in the presence of the following: - When there is a tendency to haemorrhage following acute trauma or fracture; - Following recent surgical procedures when muscle contraction may disrupt the healing process; - Over areas of the skin which lack normal sensation. Powered muscle stimulators and garments should be kept out of the reach of children. Powered muscle stimulators should be used only with the garments and electrodes recommended for use by the manufacturer. Stimulation should not be applied when in the bath or shower. The studs and electrodes must not be connected to other objects. Possible Adverse Reactions A small number of isolated skin reactions have been reported by people using muscle stimulation devices, including allergies, a prolonged reddening of the skin and acne. On very rare occasions, first-time users of NMES have reported feeling light-headed or faint. We recommend that you use the product while seated until you become accustomed to the sensation. Contact the careline if: Your unit is not working correctly. Do not use it in the meantime. You experience any irritation, skin reaction, hypersensitivity or other adverse reaction. You should, however, note that some reddening of the skin can appear under the belt during and for a short time after a session. Note: An effective treatment should not cause undue discomfort. 6

Important: For first time users, muscle stimulation can be an unusual sensation. We recommend that you begin with low stimulation intensities to familiarise yourself with the sensation before progressing to higher stimulation intensities. Do not over exert yourself when using muscle stimulation. Any workout should be at a level comfortable for you. Neurotech will not accept responsibility if the guidelines and instructions supplied with this unit are not followed. Although compliant with applicable EMC requirements, this device may still interfere with more sensitive equipment, please move away or switch off. Neurotech NMES and TENS devices can be used safely and effectively at home without medical supervision. Please read the instructions carefully, in particular the guidance on contra-indications and other precautions. We recommend that you consult a qualified medical professional before first starting a treatment regime with TENS or NMES, to ensure there is nothing about your specific medical condition which would affect safety of use. Similarly, if your health status deteriorates in any way, we recommend you check back with your medical professional to see if it is safe to continue to use TENS or NMES. CONTRAINDICATIONS, WARNINGS AND PRECAUTIONS 7

2.0 Frequently Asked Questions Q: What is Neurotech Recovery - Back? A: The Neurotech Recovery - Back consists of a back garment, an abdominal garment and a controller. It is an innovative, garment-based solution specifically designed to facilitate the frequent and correct positioning and repositioning of multiple electrodes for the treatment of the lower back and abdominal muscles. The Neurotech Plus Controller is a unique, innovative Neuromuscular Electrical Stimulator, which offers both NMES for muscle rehabilitation and TENS stimulation for pain management. Q: What should Neurotech Recovery - Back feel like when operating? A: Using NMES: When you switch the Neurotech Plus controller on and gradually increase the intensity, you will feel a mild, comfortable tingling or buzzing sensation in your muscles. As you increase the intensity, the muscles will begin to contract. Using TENS: When you switch the Neurotech Plus controller on and gradually increase the intensity, you will feel a mild, comfortable tingling or tapping sensation in your muscles. There will be no muscle contraction when using TENS. FREQUENTLY ASKED QUESTIONS 8 Q: How often should I use Neurotech Recovery Back garments? A: Your prescribing physician will advise you on the duration of your treatment program. Q: What should I do if treatment becomes uncomfortable? A: Effective treatment should not cause undue discomfort. If treatment becomes painful, try lowering the intensity level slightly, then gradually build back up to the previous level. If discomfort persists, Neurotech recommends that you contact a member of the Neurotech team or your clinician who will advise you on usage of Neurotech Recovery-Back to minimize discomfort. Q: How often should I replace the electrodes? A: With time the electrodes pick up skin debris and may need to be replaced as this makes the treatment less effective and less comfortable. If you notice the signal is weakening, even if the batteries are OK, this usually indicates that the electrodes are wearing and will soon need replacing. New electrodes can be ordered from Neurotech or your local distributor. Q: Can Neurotech Recovery - Back be used in conjunction with other forms of therapy? A: Neurotech Recovery - Back can be used as an adjunct to most forms of therapy for lower back injuries. See page for Contraindications (situations when Neurotech Recovery - Back should not be used). Q: Can I use the Abdominal Garment for post natal exercises? A: Yes, but you must wait a minimum of 6 weeks after childbirth before you begin using and you must consult your clinician first. If you ve had a caesarean in the past 3 months, consult your clinician for approval before using the garment. Q: Can Back Garments be used on other body parts? A: No. The garments should only be used as directed in this manual and not applied to any other body parts.

Q: How should I care for my Neurotech Recovery - Back? A: See page 22 for full instructions on caring for your Neurotech Recovery - Back. Q: Who should I contact if I have additional queries? A: Contact your prescribing clinician, the distributor who provided you with the Neurotech Recovery - Back or your Neurotech team if you have any questions regarding usage of Neurotech Recovery - Back. Q: What should I do if I experience an adverse reaction? A: If any irritation, skin reaction, hypersensitivity or other adverse reaction is experienced, discontinue use and contact your prescribing clinician, the distributor who provided you with the product or your Neurotech team. A slight reddening of the skin is normal under the electrodes during and for a short time after treatment. This should disappear within approximately 30 minutes. If the redness is excessive, you may have the intensity too high. This may increase the reddening in sensitive skin. Try using a lower intensity for a few days. If the problem persists, you should stop using the unit. Q: The stimulation is uncomfortable. How can I improve this? A: Make sure the electrodes are positioned correctly and that they are pressed firmly against your skin. Switch off your unit and reposition the belt if necessary. Ensure the metal studs are fully covered by the electrodes. Ensure the electrodes don t need to be changed. Q: I can feel a tingling sensation in my legs when using the abdominal garment. What should I do? A: This indicates that the electrodes are over your hip-bones. Moving the two smaller electrodes upwards and inwards on your waist (i.e. towards the centre of your body) should prevent this. Remember to pause or switch off your unit before adjusting the belt or electrodes. Q: I can feel my waist muscles exercising but not my stomach muscles when using the abdominal garment. A: Pause the programme and reposition the central electrode slightly lower on your stomach. If this doesn t help, move the 2 small electrodes to a smaller figure setting on the belt (towards the central electrode). Q: I can feel my stomach muscles exercising but not my waist muscles when using the abdominal garment. A: Pause the programme and reposition the central electrodes slightly higher on your stomach. If this doesn t help, move the 2 smaller electrodes to a larger figure setting on the belt (away from the central electrode). FREQUENTLY ASKED QUESTIONS 9

3.0 Pack Contents 1. Neurotech Plus Controller The Controller generates signals which are sent, via electrodes to your muscles or central nervous system, to cause your muscles to contract or help manage pain. Your Controller is rechargeable and takes approximately 3 hours to charge fully. 1 2 2. Battery Charger Neurotech Plus is supplied with a charger. To charge the battery pack, connect the Controller to the charger and plug the charger into an electrical socket. 4 3. Back Garment This conductive garment fastens around your lower back, for quick and easy use. It contains a connector socket, into which the Controller is plugged. 3 4. Abdominal Garment Universally sized garment, which fastens around your abdomen. It contains a connector socket, into which the Controller is plugged. Important: Only one garment can be used at a time. 7 PACK CONTENTS. Electrodes The electrodes are placed on the garments to conduct signals from the Controller to the lower back or abdominal muscles. Important: Ensure the correct electrodes are used with the correct garment. 6. Belt Extension This can be attached to one end of a belt to extend the waist size range up to 6 / 142cm. This is supplied with the Medium/ Large belt only. 7. Instruction Manual The Neurotech Recovery - Back Instruction Manual provides a guide to product use and safety information. 6 10

3.1 Neurotech Plus Controls The Neurotech Plus Controller is a portable, two-channel stimulator, which can be used either as a Neuromuscular Electrical Stimulator (NMES) or a Transcutaneous Electrical Nerve Stimulator (TENS). It is an easy to use solution, specifically designed for home use. The controller is powered by a 3.6V NiMH rechargeable battery. A battery charger is included with the product. Please refer to pages 18-19 for complete information on how to use the controller. 1. On/Off Button ( ) and Pause: Press and hold this button for 2 seconds to turn your controller on or off. During a treatment session, you can pause the stimulation by briefly pressing this button. To un-pause, briefly press this button again. 2. Intensity Buttons ( / ): Press and hold these buttons to increase and decrease the intensity of the stimulation. The right-hand buttons control the stimulation level from the right side of the garment. The left-hand buttons control the stimulation level on the left side. 3. Program Button ( P ) also Mute & Lock Functions Press and hold this button for 2 seconds before starting a treatment session to change to the desired stimulation program. To change the pre-set program during or between treatments, press and hold Program button ( P ) at anytime. After 2 seconds, the Controller will advance to the next pre-set program. Continue to hold down the (P) button until you reach your desired program number and then release. When you change the program, your treatment session will start again from the beginning. You must increase the intensity by pressing the up arrows again to the desired level. Note: See pages 26-29 for program details. 3a. Lock Function To activate/deactivate the intensity lock function, press the P button immediately followed by the left intensity up button ( ) during a treatment session. You can use this function to prevent accidental changes of intensity during a treatment session. 3b. Mute Function Press the P button immediately followed by the right intensity up ( ) button to activate/ deactivate the mute function. 1 2 3 4 NEUROTECH PLUS CONTROLS 11

4. Trigger/ Burst Button The ( i ) Button has multiple functions. The following section details these functions: 4a. Using ( i ) as a Trigger Button (NMES programs only) Once the NMES program has started press the ( i ) button to start a contraction. This contraction continues for as long as the ( i ) button is being pressed. When the ( i ) button is released, the unit goes in to relaxation mode. This will continue until the ( i ) button is pressed again. You may wish to consult your clinician on the proper use of this function. The trigger function is deactivated by pressing any of the intensity buttons. The Controller then returns to the normal program contraction/ relaxation cycle. 4b. Using ( i ) as a Burst Button (TENS programs only) When the ( i ) button is pressed during a TENS program, alternate program settings are activated so the stimulation will feel different (see pages 26-29). These program settings are maintained until the ( i ) button is pressed a second time. You may wish to consult your clinician on the proper use of this function. NEUROTECH PLUS CONTROLS. Total Treatment Time When the controller is powered on, the Total Treatment Time you have used your unit for is shown in hours and minutes. To reset the Total Treatment Time to zero, press and hold the Program ( P ) Button and Trigger/Burst Button ( i ) together for 2 seconds. 12

3.2 Neurotech Plus Controller Display Shows when the stimulation intensity is being changed, when the Trigger/Burst feature is activated and also during each contraction. Stimulation intensity from the left-hand side of the garment. Stimulation intensity from the right-hand side of the garment. Counts down the time left in the current NMES session in minutes and seconds. Counts up the time during the TENS programs. Indicates that the session has been paused. (You must press the on/off button briefly to restart the program). Indicates that the mute function is activated. This warning symbol indicates a poor contact between the unit and the electrodes or between the electrodes and the skin. Shows the battery power remaining. Shows the program currently running. Intensity lock is active you cannot change the intensity levels or the program accidentally. This symbol appears around the edge of the display during each contraction phase. CONTROLLER DISPLAY 13

4.0 Neurotech Recovery - Back Garments Neurotech Recovery - Back includes one garment for use on your back and a second garment for use on your abdomen. These are designed to help with the correct and repeatable positioning of electrodes for treating your back or abdominal muscles. Adhesive electrodes are required to use both the back and abdominal garments. Once you have placed the electrodes on the garment, you can leave them in place for future use or until they need replacing. Do not use either garment without electrodes. Back Garment sizes: Small (Waist 2-34 / 64cm-86cm) Medium/ Large (Waist 34-46 / 86cm-117cm) with a belt extension to allow fitting up to 6 / 142cm. Fig. a Abdominal Garment sizes: The abdominal garment is one size fits all - up to a waist size of 47 / 119cm. The belt extension can be used to allow fitting up to 6 / 142cm. Fig. b 4.1 Preparing a Back Treatment Ensure you use the set of four electrodes with the back garment. The inside of the garment has been printed with white electrode placement guides, showing you exactly where to place the four electrodes. Fig. c BACK TREATMENT Step 1: Place the garment on a flat surface with the inner side facing you (Fig. a). Step 2: Remove the clear plastic liners from the patterned side of the four oval electrodes (Fig. b). Step 3: Place the electrodes, patterned side down, firmly onto the garment on top of the white printed areas (Fig. c). Step 4: Remove the liners from the black side of all four electrodes (Fig. d). Do not throw these liners away as you will need to put them back on to the electrodes at the end of your session. Fig. d 14

4.2 Back Garment Placement Fig. e This section explains how to apply the back garment before using it for the first time. Electrodes should be applied to the garment before putting it on. Step 1: The back garment should always be centered over the spine. Place the peak of the curved section (pointing down) directly against your spine to align the garment and then hold the ends in both hands as shown. (Fig. e). Ensure the garment is spread equally on both sides of the body. Fig. f You can check the horizontal positioning by putting your finger into the die-cut circle on the back of the garment and feel for your spine (Fig. f). The die-cut hole should be centered low and over your spine. Step 2: Place your fingers inside the pockets at either end of the garment and pull the two ends around to meet in front of you. Wrap the left-hand side around your body first (Fig. g). Fig. g Step 3: Next, wrap the right-hand side over the left and press the two ends together so that the belt fastens comfortably. Press the ends of the garment against your body to ensure it is securely fastened. Fig. h Step 4: Then simply press the outer layer against the inner layer to fasten. (Fig. h) Step : Connect the controller to the back garment connector as shown (Fig. i) and operate as described on pages 18-19. The controller must be connected to the back or abdominal garment to work. Fig. i BACK TREATMENT 1

4.3 Preparing an Abdominal Treatment Ensure you use the set of three electrodes with the abdominal garment. The inside of the garment has been printed with white lines to indicate where the large central electrode should be placed and a further 3 placement guides either side of this, showing you exactly where to place the 2 smaller electrodes to suit your waist size. In the example below, the smaller electrodes are placed nearest to the large, central electrode. This is for a user whose waist size is 24-32. Use the sizing guidelines below to help you choose your correct electrode location. Fig. a For waist sizes 24" - 32" (61-81cm) For waist sizes 32" - 40" (81-106cm) For waist sizes 40" - 47" (106-119cm) - Extending to 6 / 142cm with belt extension Fig. b ABDOMINAL TREATMENT Step 1: Place the garment on a flat surface with the inner side facing you (Fig. a). Step 2: Remove the liners from the patterned side of the large electrode (Fig. b) and place it, patterned side down, over the central silver stud and between the white lines (Fig. c). Step 3: Next remove the liners from the patterned side of the two smaller electrodes and place them onto the garment, either side of the large electrode in the location which matches your waist size (Fig. d). Important: Before you progress, make sure that all 3 silver studs are completely covered. Press the edges of the electrodes firmly onto the belt before use. Fig. c Fig. d 16

4.4 Abdominal Garment Placement Fig. e Step 1: Remove the liners from the black side of all three electrodes (Fig. e). Do not throw these liners away as you will need to put them back onto the electrodes at the end of your session. Step 2: Hold the belt with the 3 electrodes facing towards you (Fig. f) and position the abdominal garment around your waist with the large square electrode directly over your navel (belly button). Fig. f Step 3: Stretch the ends of the belt around your waist (Fig. g), until the small electrodes are between your hip bone and ribs on either side of your body. The electrodes should be positioned as shown in Fig. h. Fig. g Step 4: Fasten the belt tightly around your waist, but not so tight as to cause discomfort. The electrodes are water-based, so you may find they are cool when placed on your skin. Step : Connect the Neurotech Plus Controller to the garment and operate as described on pages 18-19 (Fig. i). Fig. h Fig. i ABDOMINAL TREATMENT 17

.0 Using the Neurotech Plus Controller Fig. a USING THE NEUROTECH PLUS CONTROLLER Step 1: Connect the controller to the charger (Fig. a) and plug the charger into an electrical socket. You will know the battery pack is charging when the unit display shows a battery symbol with 3 bars that turn on and off. It will take approximately 2-3 hours to fully charge. The controller is fully charged when the battery symbol and its 3 bars remain on. To remove the controller from the charger, press the buttons on each side of the unit connector and pull apart. Notes: Do not leave your controller connected to the charger when the battery is fully charged. Do not leave your charger plugged into an electrical outlet when not in use. Step 2: Ensure that the controller is switched off and connect it to the garment, by plugging it into the garment socket (Fig. b). The controller and conductive garment must be correctly connected for the garment to work - this is a safety feature. Step 3: Switch on the controller by pressing the On/Off ( ) button for 2 seconds (Fig. c). When the screen changes to the timer, press the 2 down intensity buttons ( ) to verify your controller is connected to the correct garment type. This is indicated by the U-number which appears on screen for 3 seconds (see page 29 for garment types). Step 4: Select your desired program by pressing the program button (P - Fig. d) until your program number appears on the display. Then start the treatment by increasing the intensity (Fig. e). Step : As you increase the left or right intensity buttons (Fig. e) you will feel the stimulation increasing on the corresponding side of the garment. You will also see the intensity level for that side increasing on the controller s display. Increase the intensity on both sides until you feel a firm, comfortable contraction. This will vary from person to person. If you are using a TENS program, increase intensity to a comfortable level, but not one that will cause a muscle contraction. The intensity level ranges from 0-99. Step 6: Continue increasing the intensity throughout the session if possible. For NMES programs, you will feel the muscle contractions getting stronger as the intensity increases. Always reduce the intensity if you feel any discomfort. You can utilise the intensity lock function when you find a comfortable level of stimulation. Fig. b Fig. c Fig. d Fig. e 18

Pausing a session If you wish to pause a session before it is finished, simply press the on/off button briefly (Fig. f). The display will show that the unit is paused ( ). To resume the session, briefly press the on/off button again. The display will return to its normal mode. Step 6: On NMES programs the treatment session is completed when the counter reaches zero. The controller will also beep to indicate the end of the session. Switch the controller off by pressing the On/ Off button for 2 seconds ( ). Should you forget to do this, the controller will switch off automatically after 20 seconds anyway. Fig. f Fig. g Step 7: Disconnect the controller from the garment by pressing the buttons on either side of the connector and pulling the two sections apart (Fig. g). Remove the garment by carefully peeling the garment off your back or abdomen. Ensure that the electrodes remain attached to the garment. Then place the garment on a flat surface with the electrodes facing you and replace the liners on the black side of each one. If the electrodes have lifted slightly, press the edges back onto the garment. Fold the garment, ensuring that the electrodes remain flat and store the garment, with the electrodes still attached, on a flat surface in a cool dry place. USING THE NEUROTECH PLUS CONTROLLER 19

6.0 Problem Solving Guide Problem Possible cause Solution The display doesn t come on and there s no signal from the controller Controller not switched on Battery pack is fully discharged Press and hold the On/Off button for 2 seconds to switch the controller on Recharge the battery pack The battery symbol is flashing/ there s ineffective stimulation The battery charge is low Recharge the battery pack The contractions are very weak, even when the intensity is high Electrodes are not covering the metal studs Electrodes not fully in contact with the skin The battery charge is low Place the electrodes completely over the metal studs Fasten the garments more tightly Recharge the battery pack PROBLEM SOLVING GUIDE The warning symbol appears on the display Unpleasant feeling beneath the electrodes ERR has appeared on the display Electrodes not fully in contact with the garment or the skin Electrodes are worn Controller is not properly attached to the garment Electrodes not fully in contact with the skin Electrodes are worn Lotions, pigmented areas or dry spots are present on the skin Error message, indicating a problem with the controller Ensure the electrodes are pressed firmly against the garment and the skin Contact your local Neurotech supplier for replacement electrodes Ensure the controller and garment are properly connected Ensure the electrodes are pressed firmly against the skin Contact your local Neurotech supplier for replacement electrodes Remove any lotions or oils by washing the skin Switch the controller off and on again. It should now work without problems. If the error message persists, call your distributor 20