ENGLISH/DANSK OWNERS MANUAL VLMC1800 Projector bracket 180 cm
ENGLISH PAGE 1 WARNING Please be sure to read this owner s manual and use your product only in accordance with the instructions. During installation take care to adhere to workplace health and safety laws Attach the bracket to a rated load-bearing structure. NEVER MOUNT CAGE OR BRACKET DIRECTLY TO A FALSE CEILING! Do not cut or drill any parts above head height. This should all be done using the correct safety equipment at floor level. Avoid overstretching which might result in the ladder tipping over. SWL (safe working load): 20kg If you are unsure about the load-bearing capacity of the structure you are attaching the bracket to, we recommend testing it with your body weight by hanging off it gently. If you are uncomfortable doing this, it is probably not safe.
ENGLISH PAGE 2 CONTENTS 1 x Manual 1 x Assembled Bracket x Pole Trim Disk 1 x Spanner 1 x Fall-arrest safety cable 4 x M10 bolts with plastic rawl plugs for ceiling attachment 1 x Hex Key 4 x M8x8 Pin Hex Bolts 4 x M8x14 Pin Hex Bolts 4 x Threaded sleeves 4 x M5x43 bolts for projector attachment 4 x M4x43 bolts for projector attachment 4 x M3x43 bolts for projector attachment 4 x M2.5x43 pan slot bolts for projector attachment 1 x Drilling jig 1 x Bottom yoke cover 1 x Tilting top mechanism
ENGLISH PAGE 3 BRACKET PARTS 1. Top plate 2. Ceiling Yoke. Top Coupler 3. 1.6m Pole 4. Bottom Yoke 5. Universal Spider Fitting ALTERNATIVE ASSEMBLY CONFIGURATIONS: Option A Option B Option C Standard configuration Sloped ceiling fitting installed Close-coupled without a pole
ENGLISH PAGE 4 INSTALLATION INSTRUCTIONS To make installation quick and easy, this product has already been partially assembled. This bracket is designed to be modular, and interchange with brackets that use the same 2 (51mm) pole standard. Assembly for the standard configuration (A) and sloped ceiling configuration (B): Use the M8 bolts and Rawl plugs included to fix top yoke to the ceiling. For concrete ceilings use appropriate fixings. 1. Ceiling 2. Rawl plug 3. M10x25 Bolt 4.Top Yoke 5. Ceiling bolt Hold the pole in place and measure the length required. For best results the lens of the projector should have a few inches above the axis with the top of the screen. 4. Projector 5. Screen
ENGLISH PAGE 5 Cut pole to length at ground level using a pipe cutter. You will need to drill new holes in the end of the pole a. Fit the drilling jig onto the end of the pole which has just been cut b. Use the included Hex key to tighten jig onto the pole. c. Place the jig and pole on the ground. Hold down with one foot and drill. d. Remove jig. 1. Pole 2. Hex Bolt 3. Drilling jig
ENGLISH PAGE 6 For the standard configuration attach the pole to the top coupler, then attach the top coupler directly to the ceiling yoke. For the sloped ceiling configuration attach the pole to the top coupler, then connect the top coupler to the tilting mechanism, then connect all to the ceiling yoke. Option A: Option B: Attach the projector to the spider/bottom yoke fitting to the projector, and attach all to the pole. 1. Universal Spider Fitting 2. Projector 3. Pole
ENGLISH PAGE 7 Thread the input and power cables through the bracket s cable management system. Input and Power Cables If you have a false ceiling, fit the included trim disk. 1. False Ceiling 2. Trim Disk
ENGLISH PAGE 8 Fix one end of fall-arrest cable to pole, and the other end to projector. 1. Bottom pole fitting 2. Fall-arrest cable 3. Projector Turn on the projector on to calibrate image and adjust tilt. Lock off bottom yoke bolts. Fit the included cover over the swivel yoke. 1. Cover Assembly for Option C 1. Use the M8 bolts and Rawl plugs included to fix top yoke to the ceiling. For concrete ceilings use appropriate fixings. 2. Ceiling 3. Rawl plugs 4. M10x25 Bolt 5. Top Yoke 6. Ceiling bolt
2 ENGLISH PAGE 9 Attach the projector to the spider/bottom yoke fitting to the projector, and attach all to the top piece of the tilting mechanism. Fix one end of fall-arrest cable to pole, and the other end to projector. OWNERS MANUAL 1.Universal Spider Fitting 2.Projector 3.Top piece of tilting mechanism 4.Input cables 5. Fall-arrest cable
DANSK MONTAGEVEJLEDNING VLMC1800 Projector bracket 180 cm Er du usikker på monteringsstedets bæreevne, foreslår vi, at du tester det med din kropsvægt ved forsigtigt at hænge ned i armene på det pågældende sted. Er du ikke tryg ved at gøre dette er det formodentlig ikke sikkert.
DANSK SIDE 2 INDHOLD 1x Manual 1 x Samlet Beslag x Trimskive 1 x Spændenøgle 1 x Faldsikringskabel 4 x M10 bolte med plastik rawl plugs til loftmontering 1 x Nøgle 4 x M8x8 bolte 4 x M8x14 bolte 4 x Gevindskårne bøsninger 4 x M5x43 bolte til fastgørelse af projektor 4 x M4x43 bolte til fastgørelse af projektor 4 x M3x43 bolte til fastgørelse af projektor 4 x M2.5x43 pan slot bolte til fastgørelse af projektor 1 x Boreskabelon 1 x Bundcover 1 x Top vippemekanisme
DANSK SIDE 3 BESLAGETS DELE 1. Loftbeslag 2. Top samlebeslag 3. 1.6m stang 4. Bund styr 5. Universal Spider Fitting ALTERNATIVE SAMLINGSKONFIGURATONER: Mulighed A Mulighed B Mulighed C Standardkonfiguration Top vippemekanisme installeret Montering uden stang
DANSK SIDE 4 INSTALLATIONSINSTRUKTIONER For at gøre installationen nem og hurtig er dette produkt allerede delvist samlet. Beslaget er designet modulært og vil fungere sammen med beslag, der anvender den samme 2 (51mm) stang standard. Samlevejledning for standard konfiguration (A) og skråt loft konfiguration (B): Anvend M8 boltene og de medfølgende Rawl plugs til at fastgøre loftbeslaget til loftet. I tilfælde af betonloft, anvend da passende fastgørelsesmaterialer. 1. Loft 2. Rawl plug 3. M10x25 Bolt 4. Loftbelag 5. Loft bolt Hold stangen fast og mål den nødvendige længde. For at opnå det bedste resultet bør projektorens linse befinde sig 5-10 cm over midteraksen af lærredet. 1. Projektor 2. Lærred
DANSK SIDE 5 Tilskær stangen i den ønskede lændge med en rørskærer. Efter tilskæring er det nødvendigt at bore nye huller i stangens endea. Sæt boreskabelonen på enden af den stang, der er blevet tilskåret.: A. Anvend den medfølgende nøgle til fastgøring af boreskabelonen på stangen. B. Placér skabelon og stang på gulvet. Hold fast med en fod og bor hullet. C. Afmontér boreskabelonen. 1. Stang 2. Bolt 3. Boreskabelon I standardkonfigurationen, fastgør stangen til top samlebeslaget og fastgør efterfølgende Top samlebeslaget direkte til Loftbeslaget. I skråt loft konfigurationen, fastgør stangen til Top samlebeslaget, derefter sammensættes Top samlebeslag og Top vippemekanisme og efterfølgende fastgøres det hele til Loftbelaget. Mulighed A: Mulighed B:
DANSK SIDE 6 Fastgør projektoren til Spider-Fitting-beslaget og fasgør det hele til stangen.universal Spider Fitting 1. Projektor 2. Stang
DANSK SIDE 7 Før input- og strømkabler gennem beslagets kabelføringssystem. Såfremt du har nedsænket loft, montér den medfølgende Trimskive. 1. Nedsænket loft 2.Trimskive
DANSK SIDE 8 Fastgør den ene ende af faldsikringskablet til stangen og den anden ende til projektoren. 1. Bundstyr 2. Faldsikringskabel3. Projektor Tænd projektoren, kalibrer billedet og justér hældningen. Lås bundjusteringsboltene. Sæt det medfølgende cover over bundstyret. 1. Cover
DANSK SIDE 9 Samlevejledning for montering uden stang (C) 1.Anvend M8 boltene og de medfølgende Rawl plugs til at fastgøre loftbeslaget til loftet. I tilfælde af betonloft, anvend da passende fastgørelsesmaterialer. 1. Loft 2. Rawl plugs 3. M10x25 Bolte 4. Loftbeslag 5. Loft bolt Fastgør projektoren til Spider-Fitting-beslaget og fasgør det hele til Top vippemekanismen. Fastgør den ene ende af faldsikringskablet til stangen og den anden ende til projektoren. MANUAL OWNERS MANUAL 1.Universal Spider Fitting 2.Projektor 3.Top vippemekanisme 4.Input kabler 5.Faldsikringskabel