DANSK INSTALLATIONSVEJLEDNING DS Pro Lærred med motor Udpakningsinstruktioner Åben indpakningen forsigtigt og læg indholdet på et stykke pap eller en anden beskyttende overflade for at undgå beskadigelse. Kontroller at pakkens indhold stemmer overens med tilbehørsoversigten på næste side. Kontroller også om de medfølgende komponenter er modtaget ubeskadiget. Brug ikke beskadigede eller defekte dele. Vigtige sikkerhedsoplysninger Montér og brug dette produkt med varsomhed. Læs venligst vejledningen inden påbegyndelse af montering og følg nøje alle instruktioner. Benyt passende sikkerhedsudstyr under montering. Kontakt venligst en kvalificeret håndværker for hjælp hvis du ikke forstår vejledningen eller er i tvivl om sikkerheden ved montering. Hvis du er i tvivl om din vægkonstruktion bedes du konsultere en kvalificeret installatør. Brug ikke dette produkt til andre formål, eller i andre konfigurationer end de udtrykkeligt angivne i denne vejledning. Vi fraskriver os hermed ethvert ansvar eller skade som følge af forkert montering eller forkert brug af dette produkt. ADVARSEL! Dette lærred skal være forsvarligt fastgjort til væggen. Hvis det ikke er monteret korrekt, kan det resultere i, at lærredet falder ned og eventuelt beskadiger personer eller udstyr. DS-DISPLAY A/S SKELMARKSVEJ 6 2605 BRØNDBY WWW.DS-DISPLAY.DK TELEFON 36 720 720 FAX 36 720 722 1
DANSK TILBEHØRSOVERSIGT (2) Vægbeslag (1) Kassette (1) Fjernbetjening (1) IR-modtager (1) Kontrolpanel (1) Strømkabel Om brug af lærred 1. Under op- og nedrulning må lærreddugen ikke komme i kontakt med andre genstande. 2. Lærredet skal være fri for støv og snavs før lærredet rulles op. 3. Vær opmærksom på at lærredet rulles korrekt op i kassetten. 4. Lærredet må ikke monteres i fugtige lokaler. 5. Lærredet kan rengøres med en fugtig klud. MONTERINGSSKRUERNE MÅ IKKE OVERSPÆNDES. BRUG AF FORKERT SKRUEDYBDE KAN BESKADIGE KASSETTEN TIL LÆRREDET. 2
DANSK JUSTERING AF STOP Step 1 Justering af stop - nedadgående retning 1. Justeringsskrue (a) benyttes til at justere autostoppet i nedadgående retning. Hvis autostoppet skal være højere oppe (lærredhøjden bliver mindre) skal du dreje mod pilen/uret. For at justere autostoppet, skal du bruge en umbraco nøgle størrelse 5 mm. a Step 2 Justering af stop - opadgående retning 2. Justeringsskrue (b) benyttes til at justere autostoppet i opdadgående retning. Drej mod urets retning, hvis du vil have stoppet længere op mod kassetten. For at justere autostoppet skal du bruge en umbraco nøgle 5 mm. b 3
TAK FORDI DU HAR VALGT ET AF VORES PRODUKTER. DS-DISPLAY A/S SKELMARKSVEJ 6 2605 BRØNDBY WWW.DS-DISPLAY.DK TELEFON 36 720 720 FAX 36 720 722 4
ENGLISH INSTALLATION INSTRUCTION DS Pro electric screen Unpacking Instructions Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. Important Safety Information Install and operate this product with care. Please read this instruction before beginning the installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation. Please call a qualified installation contractor for help if you don t understand these directions or have any doubts about the safety of the installation. If you are uncertain about the nature of your ceiling, consult a qualified installation contractor. Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaims any and all liability or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product. CAUTION! This screen must be securely attached to the wall. If the screen is not properly installed it may fall, resulting in possible injury and/or damage. DS-DISPLAY A/S SKELMARKSVEJ 6 2605 BRØNDBY WWW.DS-DISPLAY.DK TELEFON 36 720 720 FAX 36 720 722 5
ENGLISH SUPPLIED PARTS LIST (2) Wall bracket (1) Screen cassette (1) Remote control (1) IR-receiver (1) Control box (1) Power cord How to use the screen 1. During up and lowering the screen should not come into contact with other objects. 2. The screen must be free of dust and dirt before rolled up. 3. Please note that the screen is rolled up properly in the screen cassette. 4. The screen should not be installed in damp rooms. 5. The screen can be cleaned with a damp cloth. DO NOT OVER-TIGHTEN THE SCREWS. USING THE INCORRECT SCREW DEPTH MAY CAUSE DAMAGE TO YOUR SCREEN CASSETTE. 6
ENGLISH Step 1 Adjusting the stop - downward direction 1. Adjustment screw (a) is used to adjust the auto stop in a downward direction. If auto stop must be further up (screen height becomes less), turn toward the arrow/counter-clockwise. For this operation use an Allen key size 5 mm. a Step 2 Adjusting the stop - upward direction 2. Adjustment screw (b) is used to adjust the auto stop in an upward direction. Turn counter-clockwise if you would like the stop further up towards the cassette. For this operation use an Allen key size 5 mm. b 7
ENGLISH THANKS FOR CHOOSING ONE OF OUR PRODUCTS. DS-DISPLAY A/S SKELMARKSVEJ 6 2605 BRØNDBY WWW.DS-DISPLAY.DK TELEFON 36 720 720 FAX 36 720 722 8