FØDEVARE EGNEDE PLASTPOSER, SAMT EMBALLAGE FOLIER. N.H. Emballage A/S fremstiller plastposer samt emballagefolier til emballering af fødevarer. Den primære produktion af plastposer bestemt til direkte kontakt med fødevarer består af følgende: Spidsposer til konfekture, som fremstilles i henholdsvis Polyethylene, ( LD-PE ) samt Polypropylene ( CPP ) Engangs sprøjteposer, som fremstilles udelukkende i Polyethylene ( LD-PE ) Pakkefilm fremstilles udelukkende i monofolier, bestående af : LD-PE. CPP, samt Orienteret Polypropylene ( BOPP ). Dokumentation for fødevaregodkendelse af ovennævnte produkter foreligger fra vore leverandører. Trykfarverne som anvendes i virksomheden indkøbes fra Flint Group, og er godkendt til indirekte kontakt med fødevarer. Indirekte kontakt betyder at tryksiden skal være udvendig på emballagen. Råvarerne til produktionen indkøbes i form af færdig extruderede folier. Alle folier som indkøbes hos N.H. Emballage er dokumenteret fødevare egnede, i henhold til FDA ( USA ) og EEC ( EU ), folierne overholder ligeledes specifikationerne i bekendtgørelse nr. 1102 af 9/11 2006, der er den danske bekendtgørelse for de europæiske direktiver såsom Commision Directive 2002/72/EC, 2004/1/EC, 2004/19/EC og 2005/79/EC, 1935/2004, og 2007/19EC, og bekendtgørelse nr. 167 af 3. marts 2009. Specifikationer for anvendelse af produkterne. Produkter fremstillet af LD-PE, samt CPP er egnede til tørre, vandholdige, samt fede fødevarer, og kan anvendes til opbevaring ved køl, frys, samt stuetemperatur. Produkterne må ikke anvendes i ovn eller microovn. De af N.H. Emballage fremstillede produkter lever op til reglerne i forordning 2023/2006 om god fremstillings praksis ( GMP ) Mærkning: Alle produkter fremstillet af N.H. Emballage, som er bestemt til kontakt med fødevarer, er mærket med glas-gaffel symbol Mærkningen indeholder ligeledes et produktions ordre nr. PO. Xxxxx, samt fremstillingstidspunkt i form af uge / år. Kontrol / Egenkontrol N.H. Emballage A/S er naturligvis underlagt kontrol besøg fra fødevarestyrelsen, og har ligeledes egenkontrol i henhold til gældende regler. Rapporter fra fødevarestyrelsens kontrol besøg kan findes på nettet, under www.fvst.dk, samt på vores hjemmeside under spids og sprøjteposer. Nebel den. 17. marts 2009 Direktør Torben Thomasen
Spannebaek 25 DK-4300 Holbaek Denmark E-mail: ulfoss@ulfoss.dk Telephone: +45 59 43 57 00 Telefax: +45 59 43 71 40 Polyethylene film type specification Type: 32226 Application: Treated for printing Quality: LDPE Melt Index: ca./approx. 0.8 g/10 min 190 C, 2.16 Kg ASTM 1238 Density: ca./approx. 0.92 g/cm 3 ASTM-D 1505 Thickness: 0.040 0.050 mm Coefficient of friction 0.18 0.05 ASTM-D 1894 Raw material documentation The above product meet the requirements for food packaging material of the following Recommendations / Legislations: LDPE part: BfR Bedarfsgegenständeverordnung 23.12.1997, Änderungen 21. Dezember 2000, 7. April 2003, 13. Juli 2005, 30. November 2006 und 20. Dezember 2006 sowie BfR-Empfehlungen A III, Polyethylen, Stand. 1.4.2006. FDA EU CFR, Title 21 (2007), 177.1520 (a)(2), (b) and (c)2.1 Olefin Polymers. Regulation (EC) No 1935/2004 and Commission Directives 2002/72/EC, amended by 2004/1/EC, 2004/19/EC, 2005/79/EC and 2007/19/EC. Page 1
EEC directive 2002/72 states that the overall migration from plastic materials into foodstuffs must not exceed 10 mg/dm 2 (at 40 C after 10 days). According to test procedure DS/ENV 1186 the overall migration measured on 3 % acetic acid, olive oil and 15 % ethanol (at 40 C after 10 days) of this product is much lower than the stated limit. In accordance with Directive 2004/19/EC shall additives, which are authorised as food additives and flavourings, not migrate into foodstuff in quantities exceeding the restriction in Directive 89/107/EEC and 88/388/EEC. This product contains alpha-tocopherol (CAS No. 10191-41-0), which is authorised as a food additive with restriction mentioned in Directive 89/107/EEC or 88/388/EEC. Because of the physical characteristics of the product we assume, that the components do not migrate into the foodstuff. This product complies with the EC Directive 2001/95/EC concerning General Product Safety. We hereby confirm, that the contents of Lead, Cadmium, Mercury and Hexavalent Cronium in the product don t exceed the value of 100 ppm, which is valid according to the Packaging and Waste Directive 94/62/EEC as per 30 th June 2001. The product does not contain substances labelled as eco-toxic (danger symbol N ). We can also confirm that there is no presence of BADGE, BFDGE or NOGE in our materials, which are of concern in Commission Regulation (EC) No 1895/2005. Please note that it is the responsibility of the manufactures of finished food contact articles to make sure that these articles are in compliance with the migration requirements. Holbaek d. 25-04-2008 Ulfoss Plastic A/S Maria Ekelund, Quality Coordinator Page 2