Liste over relevante statistik standarder Betegnel se Nummer Status Udga Udga ve nr. ve År titel Dansk titel DS/ 2602 P 2 1981 Statistical interpretation of test results - Estimation of the mean - Statistisk fortolkning af prøvnings Estimation af - Confidence interval middelværdi. Konfidensinterval DS/ 2854 P 1 1976 Statistical interpretation of data - Techniques of estimation and tests relating to means and variances Statistisk fortolkning af data. Estimationsmetoder og test for middelværdier og varianser DS/ 2859-0 T 1 1995 Sampling procedures for inspection by attributes Metoder for stikprøveinspektion ved alternativ variation - Part 0 : Introduction to the 2859 attribute sampling system Del 0:Introduktion til -systemet af stikprøveplanerfor inspektion ved alternativ variation DS/ 2859-1 P 2 1999 Sampling procedures for inspection by attributes Metoder for stikprøveinspektion ved alternativ variation - Part 1 : Sampling plan indexed by acceptable quality level (AQL) for lot-by-lot inspection Del1: Puljer af stikprøveplaner opstillet efter kvalitetsniveau for godkendelse (AQL) for inspektion af på hinanden følgende partier DS/ 2859-1 C 1 2001 Technical corrigendum 1 : 2001 DS/ 2859-1 Dam 1 2010 d DS/ 2859-2 P 1 1992 Sampling procedures for inspection by attributes Metoder for stikprøveinspektion ved alternativ variation - Part 2 : Sampling plans indexed by limiting quality (LQ) for isolated lot inspection Del 2: Stikprøveplaner opstillet efter utilfredsstillende kvalitet (LQ) for inspektion af enkeltstående partier DS/ 2859-3 P 2 2005 Sampling procedures for inspection by attributes Metoder for stikprøveinspektion ved alternativ variation - Part 3 : Skip-lot sampling procedures Del 3: Procedurer for overspringelse af på hinanden følgende partier DS/ 2859-4 P 2 2002 Sampling procedures for inspection by attributes Metoder for stikprøveinspektion ved alternativ variation - Part 4 : Procedures for assessment of declared quality levels Del 4: Stikprøveplaner til vurdering af overensstemmelse med givne kvalitetsniveauer DS/ 2859-5 P 1 2006 Sampling procedures for inspection by attributes Metoder for stikprøveinspektion ved alternativ variation - Part 5: System of sequential sdampling plans indexed by AQL for lot-by-lot inspection Del 5: System af sekventielle stikprøveplaner opstillet efter kvalitetsniveau for godkendelse (AQL) for inspektion af på hinanden følgende partier DS/ 2859-10 P 1 2007 Sampling procedures for inspection by attributes - Part 10: Introduction to the 2859 series of standards for sampling for inspection by attributes Metoder for stikprøveinspektion ved måling med alternativ variation - Del 10: Introduktion til 2859-systemet af stikprøveplaner
DS/ 3207 P 1 1975 Statistical interpretation of data -- Determination of a statistical tolerance interval DS/ 3301 P 1 1975 Statistical interpretation of data - Comparison of two means in the case of paired observations DS/ 3494 P 1 1980 Statistical interpretation of data - Power of tests relating to means and variances DS/ 3534-1 Part 1 : Probability and general statistical terms DS/ 3534-2 Part 2 : Statistical quality control DS/ 3534-3 Part 3 : Design of experiments DS/ 3534-4 CD 1 Statistics -- Vocabulary and symbols -- Part 4: Survey sampling Statistisk fortolkning af data. Styrke af test vedrørende middelværdier og varianser P 2 2007 Statistics - Vocabulary and symbols Statistik. Ordliste og symboler. Generelle statistiske termer og termer for sandsynlighedsteori P 2 2007 Statistics - Vocabulary and symbols Statistik. Ordliste og symboler. Del 2: Anvendt statistik P 1 2000 Statistics - Vocabulary and symbols Statistik. Ordliste og symboler. Del 3: Forsøgsplanlægning DS/ 3951-1 P 2 2007 Sampling procedures for inspection by variables - Part 1 : Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL DS/ 3951-2 P 2 2007 Sampling procedures for inspection by variables - Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics DS/ 3951-2 AMD 1 2009 DS/ 3951-3 P 2 2007 Sampling procedures for inspection by variables - Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection DS/ 3951-4 DIS 1 Sampling procedures for inspection by variables - Part 4: Procedures for assessment of declared quality levels Metoder for stikprøveinspektion ved måling med kontinuert variation. Del 1: Specifikation af enkelte stikprøveplaner opstillet efter kvalitetsniveau for godkendelse (AQL) for inspektion af på hinanden følgende partier vedr. en kvalitetsparameter og en AQL-værdi Procedurer for stikprøveinspektion ved måling med kontinuert variation - Del 2: Generel specifikation for enkelt stikprøveplaner opstillet efter kvalitetsniveau for godkendelse (AQL) til inspektion af på hinanden følgende partier gældende for uafhængige kvalitetsegenskaber Procedurer for stikprøveinspektion ved måling med kontinuert variation - Del 3: Dobbelt-stikprøveplaner opstillet efter kvalitetsniveau for godkendelse (AQL) til inspektion af på hinanden følgende partier Procedurer for stikprøveinspektion ved måling med kontinuert variation - Del 4: Procedurer for vurdering af erklærede kvalitetsniveauer
DS/ 3951-5 P 1 2007 Sampling procedures for inspection by variables - Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation) DS/ 5479 P 2 2004 Statistical interpretation of data - Tests for departure from the normal distribution DS/ 5725-1 P 1 1995 Accuracy (trueness and precision) of measurement methods Part 1 : General principles and definitions DS/ C 1 2000 Technical corrigendum 1: DS/ 5725-2 P 1 1995 Accuracy (trueness and precision) of measurement methods Part 2 : Basic method for the determination of repeatability and reproducibility of a standard measurement method DS/ C 1 2002 Technical corrigendum 1: 2002 DS/ 5725-3 P 1 1995 Accuracy (trueness and precision) of measurement methods Part 3 : Intermediate measures of the precision of a standard measurement method DS/ C 1 2002 Technical corrigendum 1: 2002 DS/ 5725-4 P 1 1995 Accuracy (trueness and precision) of measurement methods Part 4 : Basic methods for the determination of the trueness of a standard measurement method Sampling procedures for inspection by variables - Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation) Statistisk fortolkning af data - Test for afvigelse fra normalfordeling Del 1: Generelle principper og definitioner Del 2. Grundlæggende metode til bestemmelse af repeterbarhed og reproducerbarhed for en standardiseret målemetode Del 3. Mellemliggende mål for præcision af en standardiseret målemetode Del 4: Grundlæggende metoder til bestemmelse af en standardiseret målemetodes korrekthed Del 5: Alternative metoder til bestemmelse af præcisionen for en standardiseret målemetode DS/ 5725-5 P 1 1998 Accuracy (trueness and precision) of measurement methods Part 5 : Alternative methods for the determination of the precision of a standard measurement method DS/ C 1 2005 Technical corrigendum 1: 2005 DS/ 5725-6 P 1 1995 Accuracy (trueness and precision) of measurement methods Part 6 : Use in practice of accuracy values DS/ C 1 2010 Technical corrigendum 1: 2010 DS/ 7870-1 P 2 2007 Control charts - General guide and introduction Kontrolkort - Del 1: Generel vejledning Del 6: Praktisk brug af værdier for nøjagtighed
7870-2 CD 1 Control charts -- Part 2: Shewhart control charts DS/ 7870-3 DIS 1 Control charts - Part 3: Acceptance control charts Kontrolkort - Del 3: Metode for godkendelse af kontrolkort DS/ 7870-4 DIS 1 Control charts - Part 4: Cumulative sum charts Kontrolkort - Del 4: Kumulativ kort 7871 TR 1 1997 Cumulative sum charts - Guidance on quality control and data analysis using CUSUM techniques DS/ 7873 P 1 2009 Control charts for arithmetic average with warning limits Kontrolkort til aritmetisk gennemsnit med advarselsgrænser DS/ 7966 P 1 1993 Acceptance control charts Godkendelseskontrolkort DS/ 8258 P 1 1991 Shewhart control charts Shewhart-kontrolkort DS/ 8258 C 1 1993 Technical corrigendum 1: 1993 DS/ 8422 P 2 2007 Sequential sampling plans for inspection by attributes Stikprøveplaner for sekventiel stikprøveudtagning ved måling med alternativ variation DS/ 8423 P 2 2008 Sequential sampling plans for inspection by variables for percent nonconforming (known standard deviation) Stikprøveplaner for sekventiel stikprøveudtagning ved måling med kontinuert variation (kendt standardafvigelse) 8550-01 TR 2 2007 Guidance on the selection and usage of acceptance sampling systems for inspection of discrete items in lots - Part 1: Acceptance sampling 8550-02 TR 1 2007 Guidance on the selection and usage of acceptance sampling systems for inspection of discrete items in lots - Part 2: Sampling by attributes Vejledning i valg og brug af system til godkendelsesinspektion af enkelte emner i et parti - Del 1: Godkendelsesinspektion Vejledning i valg og brug af system til godkendelsesinspektion af enkelte emner i et parti - Del 2: Måling med alternativ variation 8550-01 TR 1 2007 Guidance on the selection and usage of acceptance sampling systems for inspection of discrete items in lots - Part 3: Sampling by variables Vejledning i valg og brug af system til godkendelsesinspektion af enkelte emner i et parti - Del 3: Måling med kontinuert variation DS/ 10017 TR 2 2003 Vejledning ved valg af hensigtsmæssige statistiske metoder i Guidance on statistical techniques for 9001:2000 forbindelse med 9001:2000 DS/ 10576-1 P 1 2003 Statistiske metoder - Retningslinjer for vurdering af Statistical methods - Guidelines for the evaluation of conformity overensstemmelse med specificerede krav - Del 1: Almene with specified requirements- Part 1 : General principles principper DS/ 10725 P 1 2000 Acceptance sampling plans and procedures for the inspection of bulk materials Stikprøveplaner og procedurer for godkendelsesinspektion af bulkmaterialer DS/ 11095 P 1 1996 Linear calibration using reference materials DS/ 11453 P 1996 Statistical interpretation of data - Tests and confidence intervals relating to proportions DS/ 14253-1 C 1 2000 Technical corrigendum 1 DS/ 11462-1 P 2 2007 Statistical process control system standards -Part 1 : Guideline for implementation of statistical process control Statistisk fortolkning af data.prøvninger og konfidensintervaller for relative hyppigheder Retningslinier for implementering af statistisk processtyring (SPC) - Del 1: Forudsætninger og aktiviteter
DS/ 11462-2 P 1 2010 Guidelines for implementation of statistical process control (SPC) - Part 2: Catalogue of tools and techniques Retningslinjer for implementering af statistisk processtyring (SPC) - Del 2: Katalog over værktøjer og teknikker DS/ 11648-1 P 1 2003 Statistical aspects of sampling from bulk material - Statistiske forhold i forbindelse med stikprøveudvælgelse fra bulkmateriale Part 1 : General introduction Del 1 Grundlæggende principper DS/ 11648-2 P 1 2002 Statistiske forhold i forbindelse med stikprøveudvælgelse fra Principles of sampling and statistical principles - Bulk material - bulkmateriale - Del 2 Stikprøveudtagning fra materialer på Part 2 : Sampling of particulate materials partikelform DS/ 11843-1 P 1 2003 Decision limit, detection limit, capability of detection Detektionsevne. Del 1: Termer og definitioner Capability of detection -Part 1 : Terms and definition DS/ 11843-1 C 1 2004 Technical corrigendum 1 DS/ 11843-2 P 1 2003 Capability of detection -Part 2 : Methodology - Linear calibration Detektionsevne case DS/ 11843-2 C 1 2007 Technical corrigendum 1 DS/ 11843-3 P 1 2003 Capability of detection - Part 3 : Methodology for determination of the critical value for the response variable when no calibration data are used DS/ 11843-4 P 1 2004 Capability of detection - Part 4 : Methodology for comparing the minimum detectable value with a given value DS/ 11843-5 P 1 2008 Capability of detection - Part 5: Methodology in the linear and non-linear calibration cases DS/ 11843-6 DIS 1 Capability of detection - Part 6: Methodology for the determination of the critical value and the minimum detectable values in Poisson distribution measurements DS/ 11843-7 DIS 1 Capability of detection - Part 7: Methodology based on stochastic properties of instrumental noise DS/ 12845 TR 1 2010 Selected illustrations of fractional factorial screening experiments 12888 DTR 1 Selected illustrations of gauge repeatability and reproducibility studies DS/ 13053-1 DIS 1 Quantitative methods in process improvement - Six Sigma - Part 1: DMAIC methodology DS/ 13053-2 DIS 1 Quantitative methods in process improvement - Six Sigma - Part 2: Tools and techniques Del 2: Metodik i forbindelse med lineær kalibrering Detektionsevne. Del 3: Metodik til bestemmelse af påvisningsgrænsen for en responsvariabel uden brug af kalibreringsdata Detektionsevne Del 4: Metodik til sammenligning af den mindste detekterbare værdi med en given værdi Detektionsevne - Del 5: Metodik i forbindelse med lineær og ikke lineær kalibrering Detektionsevne - Del 6: Metodik for bestemmelse af kritisk værdi og mimimum sporbare værdier i Poisson målinger Detektionsevne - Del 7: Metodik baseret på varierende instrumental støj Udvalgte illustrationer af fraktionelle faktorforsøg Kvantitative metoder i procesforbedring - Six Sigma - Del 1: DMAIC metodik Kvantitative metoder i procesforbedring - Six Sigma - Del 2: Værktøjer og teknikker
13195 NPT R Selected illustrations of response surface method DS/ 13425 TR 2003 Guide for the selection of statistical methods in standardization and specification Vejledning i forbindelse med valg af statistiske metoder i standarder og specifikationer DS/ 13448-1 P 1 2005 Acceptance sampling procedures based on the allocation of priorities principle (APP) - Part 1 : Guidelines for the APP approach Procedurer for godkendelsesinspektion baseret på princippet om allokering af prioriteter (APP) - Del 1: Vejledning i APP-metoden DS/ 13448-2 P 1 2005 Procedurer for godkendelsesinspektion baseret på princippet om Acceptance sampling procedures based on the allocation of priorities principle (APP) - Part 2 : Coordinated single sampling plans for acceptance sampling by attributes allokering af prioriteter (AAP) - Del 2: Samordnede enkeltstikprøveplaner for godkendelsesprøvning ved måling med alternativ variation 13519 NP 1 Guidance on the development and use of statistical publications supported by software DS/ 13528 P 1 2005 Statistical methods for use in proficiency testing by interlaboratory comparisons Statistiske metoder til brug ved præstationsprøvning baseret på laboratoriesammenligninger 13587 NPT R 1 Three statistical paradigms for the assessment and interpretation of measurement uncertainty 14468 DTR 1 2010 Selected illustrations of attribute agreement analysis Udvalgte illustrationer af overensstemmelsesanalyser DS/ 14560 P 1 2004 Acceptance sampling procedures by attributes - Specified quality levels in nonconforming items per million Metoder for stikprøveinspektion ved måling med alternativ variation - Specificeret kvalitetsniveau i afvigende enheder per million enheder 15725-1? DS/ 16269-4 P 1 2010 Statistisk fortolkning af data - Del 4: Påvisning og behandling af Statistical interpretation of data - Part 4: Detection and treatment outliere of outliers DS/ 16269-5 1 DS/ 16269-6 P 1 2005 Statistical interpretation of data Statistisk fortolkning af data - Part 6 : Determination of statistical tolerance intervals Del 6: Bestemmelse af statistiske toleranceintervaller DS/ 16269-7 P 1 2001 Statistical interpretation of data Statistisk fortolkning af data - Part 7: Median: Estimation and confidence intervals Del 7: Median - Estimation og konfidensintervaller DS/ 16269-8 P 1 2005 Statistical interpretation of data Statistisk fortolkning af data - Part 8: Determination of a prediction interval Del 8: Bestemmelse af prediktionsinterval 16336 NP 1 Robust parameter design (RPD) 16355 NP 1 Quality function deployment DS/ 18414 P 1 2006 Acceptance sampling procedures by attributes - Accept-zero sampling system based on credit principle for controlling outgoing quality Procedurer for stikprøveinspektion ved måling med alternativ variation - System af stikprøveplaner med godkendelsestal nul til kontrol af udgående kvalitet baseret på et kreditprincip
DS/ 18532 TR 1 2009 Guidance on the application of statistical methods to quality and Vejledning i brug af statistiske metoder inden for kvalitetsledelse to industrial standardization og industriel standardisering DS/ 21247 P 1 2005 Combined accept-zero sampling systems and process control procedures for product acceptance Kombinerede stikprøveplaner for godkendelsesprøvning med accepttal nul og proceskontrolprocedurer for produktgodkendelse DS/ 21747 P 1 2006 Statistical methods Process performance and capability statistics for Statistiske metoder Metoder til beregning af proces-performance measured quality characteristics og kapabilitet for målte kvalitetsegenskaber 21748 P 1 2004 Guide to the use of repeatability, reproductibility and trueness estimates in measurement uncertainty estimation 21749 P 1 2005 Measurement uncertainty for metrological applicaions : simple replication and nested experiments DS/ 22514-1 P 1 2009 Statistical methods in process management - Capability and performance - Part 1: General principles and concepts 22514-2 CD 1 Statistical methods in process management -- Capability and performance -- Part 2: Process capability and performance of time-dependent process models DS/ 22514-3 P 1 2009 Statistical methods in process management - Capability and performance - Part 3: Machine performance studies for measured data on discrete parts DS/ 22514-4 TR 1 2007 Statistical methods in process management - Capability and performance - Part 4: Process capability estimates and performance measures 22514-5 NWI Statistical methods in process management - Capability and performance - Part 4: Process capability estimates for attribute data DS/ 22514-6 DIS 1 Statistical methods in process management -- Capability and performance -- Part 6: Process capability statistics for characteristics following a multivariate normal distribution DS/ 22514-7 DIS 1 Statistical methods in process management Capability and performance Part 7: Capability of measurement processes DS/ 22971 TR 1 2005 Accuracy (trueness and precision) of measurement methods - Practical guidance for the use of 5725-2 : 1994 in designing, implementing and statistically analysing interlaboratory repeatabiliby and reproducibility results Statistical methods in process management - Capability and performance - Part 1: General principles and concepts Statistiske metoder i procesledelse - Kapabilitet og performance - Del 3: Analyse af maskinperformance for måleværdier på (diskrete) emner Statistiske metoder i procesledelse - Kapabilitet og performance - Del 4: Beregning af proceskapabilitet og performancemål Statistiske metoder i procesledelse - Kapabilitet og performance - Del 6: Statistisk proceskapabilitet for karakteristikker der følger normal fordeling Statistiske metoder i procesledelse - Kapabilitet og performance - Del 7: Måleprocessers kapabilitet resultater - Praktisk vejledning i brug af 5725-2:1994 ved forsøgsplanlægning, implementering og statistisk analyse i forbindelse med resultater for interlaboratoriel repeterbarhed og reproducerbarhed
DS/ 24153 P 1 2009 Random sampling and randomization procedures Metoder til tilfældig stikprøvetagning og randomisering DS/ 28801 FDIS Double sampling plans by attributes with minimal sample sizes, Prøveudtagningsegenskaber - Dobbelt prøveudtagningsplan med indexed by producer's risk quality (PRQ) and consumer's risk quality (CRQ) minimal prøvningsstørrelse kategoriseret efter producents risikokvalitet (PRQ) og forbrugers risikokvalitet (CRQ) DS/ 28808 P 1 2009 Random variate generation methods Metoder til generering af tilfældige variable DS/ 28037 TR 1 2010 Determination and use of straight-line calibration functions Bestemmelse og anvendelse af lineære kalibreringsfunktioner DS/ 29901 TR 1 2008 Selected illustrations of full factorial experiments with four factors Udvalgte eksempler på fuldfaktorforsøg med fire faktorer DS/ 29901 C 1 2009 Technical corrigendum 1 DS/ 61649 P 1 2008 Weibull analysis Weilbull-analyse DSINF 66 BOG - statistisk processtyring Guide 33 G 2 2000 Uses of certified reference materials Guide 34 G 3 General requirements for the competence of reference material 2009 producers Guide 35 G 3 Reference materials -- General and statistical principles for 2006 certification Guide 98 G 1 2008 Guide to the expression of the uncertainty of measurement Retningslinier for at udtrykke måleusikkerhed (GUM) Guide 99 G 2 International vocabulary of metrology Basic and general 2007 concepts and associated terms (VIM)